scholarly journals Wideband Printed Antenna Design Using a Shape Blending Algorithm

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Aiting Wu ◽  
Zhonghai Zhang ◽  
Boran Guan
Keyword(s):  
Optimization Method ◽  
Ultra Wideband ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Printed Antenna ◽  
Rectangular Slot ◽  
Design And Optimization ◽  
Shape Blending ◽  
The Impact ◽  
Good Agreement

The shape of the tuning stub of the wide slot printed antenna is an important factor which affects the antenna’s performances. In this paper, a new design and optimization method of wideband printed slot antenna using a shape blending algorithm is presented. The proposed antenna consists of a wide rectangular slot and a tuning stub, whose profile is formed by the shape blending outcome from a pie and a diamond shape. The method is used to design an ultra-wideband antenna. The impact on the impedance bandwidth through the antenna geometry change with the different shape blending results has been investigated and analyzed. To verify the proposed design, the antenna prototype was designed, fabricated, and measured. The measured results are compared with the simulation and show good agreement.

scholarly journals Reconfigurable 2×1 CPW-Fed Rectangular Slot Antenna Array (RSAA) Based on Graphene for Wireless Communications

2021 ◽  
Vol 36 (6) ◽  
pp. 788-795
Author(s):  
Dalia Elsheakh ◽  
Osama Dardeer
Keyword(s):  
Wireless Communications ◽  
Antenna Array ◽  
Coplanar Waveguide ◽  
Ultra Wideband ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Average Gain ◽  
Rectangular Slot ◽  
High Data ◽  
Peak Gain

This article presents a 2×1 CPW ultra wideband rectangular slot antenna array (UWB-RSAA) with a modified circular slot shape to support a high data rate for wireless communications applications. The proposed antenna array dimensions are 0.7λ×0.8λo×0.064λo at the resonant frequency 1.8 GHz. It is fabricated on Rogers RO4003 substrate and fed by using a coplanar waveguide (CPW). A graphene layer is added on one side of the substrate to realize frequency reconfigurability and improve the array gain. The proposed array acquires -10 dB impedance bandwidth of the RSAA that extends from 1.7 GHz to 2.6 GHz, from 3.2 to 3.8 GHz, and from 5.2 GHz to 7 GHz. The proposed array achieved a realized peak gain of 7.5 dBi at 6.5 GHz at 0 Volt bias with an average gain of 4.5 dBi over the operating band. When the graphene bias is increased to 20 Volt, the antenna bandwidth extends from 1 GHz to 4 GHz and from 5 to 7 GHz with a peak gain of 14 dBi at 3.5 GHz and an average gain of 7.5 dBi. The linearly polarized operation of the proposed array over the operating bands makes it suitable for short-range wireless communications .

Design of Ultra-Wideband Tapered Slot Antenna by Using Binomial Transformer with Corrugation

Frequenz ◽  
2017 ◽  
Vol 71 (5-6) ◽  
Author(s):  
Yosita Chareonsiri ◽  
Wanwisa Thaiwirot ◽  
Prayoot Akkaraekthalin
Keyword(s):  
Ultra Wideband ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Antenna Gain ◽  
Radiation Characteristics ◽  
Step Procedure ◽  
Flat Gain ◽  
Uwb Applications ◽  
Good Agreement

AbstractIn this paper, the tapered slot antenna (TSA) with corrugation is proposed for UWB applications. The multi-section binomial transformer is used to design taper profile of the proposed TSA that does not involve using time consuming optimization. A step-by-step procedure for synthesis of the step impedance values related with step slot widths of taper profile is presented. The smooth taper can be achieved by fitting the smoothing curve to the entire step slot. The design of TSA based on this method yields results with a quite flat gain and wide impedance bandwidth covering UWB spectrum from 3.1 GHz to 10.6 GHz. To further improve the radiation characteristics, the corrugation is added on the both edges of the proposed TSA. The effects of different corrugation shapes on the improvement of antenna gain and front-to-back ratio (F-to-B ratio) are investigated. To demonstrate the validity of the design, the prototypes of TSA without and with corrugation are fabricated and measured. The results show good agreement between simulation and measurement.

scholarly journals Reconfigurable 2×1 CPW-Fed Rectangular Slot Antenna Array (RSAA) Based on Graphene For Wireless Communications

2021 ◽  
Author(s):  
Dalia Elsheakh ◽  
Osama Dardeer
Keyword(s):  
Wireless Communications ◽  
Antenna Array ◽  
Coplanar Waveguide ◽  
Ultra Wideband ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Average Gain ◽  
Rectangular Slot ◽  
High Data ◽  
Peak Gain

Abstract This article presents a 2×1 CPW ultra wideband rectangular slot antenna array (UWB-RSAA) with modified circular slot shape to support high data rate for wireless communications applications. The proposed antenna array dimensions are 0.7λo×0.8λo×0.064λo at the resonant frequency 1.8 GHz and it is fabricated on a commercially available rogers RO4003 substrate (with εr = 3.5), which is fed by using coplanar waveguide (CPW). A graphene layer is added on the other side of the substrate to achieve frequency reconfigurable and improve the antenna array gain. The -10 dB impedance bandwidth of the RSAA extends from 1.7 GHz to 2.6 GHz, from 3.2 to 3.8 GHz and from 5.2 GHz to 7 GHz with peak gain of 7.5 dBi at 6.5 GHz at 0 Volt bias over the operating band with average gain of 4.5 dBi. When the graphene bias is increased to 20 Volt, the antenna bandwidth extend from 1 GHz to 4 GHz and from 5 to 7 GHz with array peak gain 14 dBi at 3.5 GHz and average gain 7.5 dBi. The proposed array achieved linear polarized behaviour over the operating bands to be suitable for short range UWB wireless communications and object detection. All simulation carried out using 3D high frequency structure simulator (HFSS) Ansys ver. 15.

Dual Band Slot Antenna for 3.5 WiMAX and 5.8 WLAN

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Sahar Chagharvand ◽  
M. R. B. Hamid ◽  
M. R. Kamarudin ◽  
Mohsen Khalily
Keyword(s):  
Radiation Pattern ◽  
Coplanar Waveguide ◽  
Single Layer ◽  
Dual Band ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Antenna Gain ◽  
Dual Bandwidth ◽  
Electromagnetic Performance ◽  
Good Agreement

This paper presents a single layer planar slot antenna for dual band operation. The antenna is fed by a coplanar waveguide (CPW) with two inverted C-shaped resonators to achieve the dual band operation. The impedance bandwidth for ǀS11ǀ < -10dB is 14% in lower band and 7% in higher band. The antenna prototype’s electromagnetic performance, impedance bandwidth, radiation pattern, and antenna gain were measured. The proposed configuration offers a relatively compact, easy to fabricate and dual band performance providing gain between 2 and 4 dBi. The designed antenna has good dual bandwidth covering 3.5 WiMAX and 5.8 WLAN tasks. Experimental and numerical results also showed good agreement after comparison.

scholarly journals Bandwidth Improvement in Bow-Tie Microstrip Antennas: The Effect of Substrate Type and Design Dimensions

2020 ◽  
Vol 10 (2) ◽  
pp. 504 ◽  
Author(s):  
Halgurd N. Awl ◽  
Yadgar I. Abdulkarim ◽  
Lianwen Deng ◽  
Mehmet Bakır ◽  
Fahmi F. Muhammadsharif ◽  
...  
Keyword(s):  
Simulation Analysis ◽  
Microstrip Antennas ◽  
Ultra Wideband ◽  
The Novel ◽  
Substrate Type ◽  
Antenna Performance ◽  
Uwb Applications ◽  
The Impact ◽  
Bow Tie ◽  
Good Agreement

In this work, the impact of substrate type and design dimensions on bow-tie microstrip antenna performance and bandwidth improvement is presented both numerically and experimentally at 4–8 GHz. The finite integration technique (FIT)-based high-frequency electromagnetic solver, CST Microwave Studio, was used for the simulation analysis. For this purpose, four bow-tie microstrip antennas were designed, fabricated, and measured upon using different materials and substrate thicknesses. Precise results were achieved and the simulated and experimental results showed a good agreement. The performance of each antenna was analyzed and the impact of changing material permittivity, antenna dimensions and substrate thicknesses on antenna performance were investigated and discussed. The measured results indicated that the slot bow-tie antenna, which is one of the novel aspects of this study, is well matched and a 2-GHz bandwidth [5–7 GHz] is obtained, which is about 50% bandwidth in comparison with the wideband applications [4–8 GHz]. The proposed structure is useful in ultra-wideband (UWB) applications. This study provides guidance in selecting material types and thicknesses for microstrip antennas based on desired applications.

CPW-Fed 8-Shaped Monopole Antenna for Ultra Wideband Applications

Frequenz ◽  
2016 ◽  
Vol 70 (11-12) ◽  
Author(s):  
Sarthak Singhal ◽  
Amit Kumar Singh
Keyword(s):  
Group Delay ◽  
Coplanar Waveguide ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Radiation Patterns ◽  
Antenna Structure ◽  
Operating Frequency Range ◽  
Good Agreement ◽  
Delay Variation

AbstractA CPW-fed 8-shaped monopole antenna for ultra wideband applications is presented. It consists of a 8-shaped monopole and two quarter elliptical coplanar waveguide ground planes. An impedance bandwidth from 5.4 GHz to 23.83 GHz is achieved. The radiation patterns are observed to be omnidirectional and bidirectional in E-and H-plane respectively at lower resonances. At higher frequencies, the radiation patterns are found to be nearly omnidirectional in both planes. The group delay variation is also observed to be constant in the operating frequency range. A good agreement is found between the simulation and experimental results. The designed antenna structure has miniaturized dimensions and wider bandwidth as compared to other already reported monopole structures.

scholarly journals Achievement of Various Widebands: A Design of Wide-Slot Antennas Using Shape Blending

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Aiting Wu ◽  
Zhonghai Zhang ◽  
Boran Guan ◽  
Liang Peng
Keyword(s):  
Geometric Structure ◽  
Design Method ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Slot Antennas ◽  
Regular Trend ◽  
Shape Blending ◽  
New Process ◽  
Convenient Model ◽  
Good Agreement

When designing printed wide-slot antennas, the shape or profile of the tuning stub is a key geometric structure that affects the impedance bandwidth of the antenna. This article introduces a new process for designing tuning stub shapes, which are the blended results of a diamond and a circle. By using different geometry shapes, the design could generate a series of bandwidths with a regular trend. Detailed investigations and analysis were conducted on some key geometry parameters to explore their impact on the impedance bandwidth of the antenna. To certify the new design method, several prototypes were simulated, developed, and measured. The experimental and simulated results showed good agreement with each other. The results indicate that by properly selecting various blended shapes, a BW range from 80.1 to 117.3% for a VSWR of less than 2 could be obtained, which provides a convenient model for a wideband antenna design.

Novel wideband slot antenna having notch-band function for 2.4 GHz WLAN and UWB applications

2011 ◽  
Vol 3 (4) ◽  
pp. 451-458 ◽  
Author(s):  
Arumugam Chellamuthu Shagar ◽  
Shaik Davood Wahidabanu
Keyword(s):  
Frequency Band ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Slot Antenna ◽  
Area Network ◽  
Rectangular Slot ◽  
Notch Band ◽  
Uwb Applications

In this paper, the design, simulation, and fabrication of a novel printed rectangular slot antenna with a band-notched function suitable for 2.4 GHz wireless local area network (WLAN) and ultra-wideband (UWB) applications is presented and investigated. Two pairs of slits are introduced into the ground plane to realize band-notched function, by tuning the position, length, and width of which a suitable rejected frequency band can be obtained. To improve the impedance matching, a rectangular cut is also made in the ground plane so that the antenna can cover 2–12 GHz frequency range. According to the measured results, the proposed antenna has a large bandwidth totally satisfying the requirement of 2.4 GHz WLAN and UWB systems, while providing the required band-notch function from 5.1 to 5.9 GHz. The study of transfer function and time-domain characteristics also indicates the band-notched function of the antenna. The radiation patterns display nearly omni-directional performance and the antenna gain is stable except in the rejected frequency band (5.1–5.9 GHz). Moreover, group delays are within 1.5 ns except for the notch band. These features make it a promising candidate for UWB wireless applications. Details of this antenna are described, and the experimental results of the constructed prototype are given.

scholarly journals Cross-Slot Antenna with U-Shaped Tuning Stub for Ultra-Wideband Applications

2008 ◽  
Vol 2008 ◽  
pp. 1-6 ◽  
Author(s):  
Dawood Seyed Javan ◽  
Mohammad Ali Salari ◽  
Omid Hashemi Ghoochani
Keyword(s):  
Radiation Pattern ◽  
Ultra Wideband ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Design Procedures ◽  
Linearly Polarized ◽  
Dimensional Parameters ◽  
Simulation Results ◽  
Novel Design ◽  
Better Than

A novel design of an ultra-wideband (UWB) slot antenna is presented. This antenna operates as a transmitter and receiver antenna. Effects of the antenna dimensional parameters are studied through experimental and simulation results. Design procedures are developed and verified for different frequency bands. The experimental and simulation results exhibit good impedance bandwidth, radiation pattern, and relatively constant gain over the entire band of frequency. Antenna gain and directivity at boresight and in their maximum states are close to each other and indicate high radiation efficiency. To use the antenna as a linearly polarized antenna, the radiation pattern in E-plane is better thanthat inH-plane.

scholarly journals Design and analysis of dual dumbbell and rectangular slots SIW cavity-backed antenna at 2.45 GHz

2021 ◽  
Vol 18 (2) ◽  
pp. 211-224
Author(s):  
Velusamy Mekaladevi ◽  
Devi Nirmala ◽  
Madasamy Jayakumar
Keyword(s):  
Slot Antenna ◽  
Substrate Integrated Waveguide ◽  
Wideband Antenna ◽  
Rectangular Slot ◽  
Simulation Results ◽  
Good Agreement

The design and realization of a wideband substrate-integrated waveguide (SIW) cavity-backed slot antenna operating at 2.45 GHz for WLAN applications are presented. Dual dumbbell-shaped slots with rectangular slots are used to achieve increased bandwidth. The bandwidth observed is 160 MHz with the dumbbell-shaped slots. Further, it has been improved up to 9.2% by adding a rectangular slot. The wideband antenna is analyzed using ANSYS HFSS and fabricated on FR-4 substrate. The measured results of the proposed design are in good agreement with the simulation results and comparable with the reported results.

Sign in / Sign up

Export Citation Format

Share Document