scholarly journals Analysis of Vibration of Roadheader Rotary Table Based on Finite Element Method and Data from Underground Coalmine

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Minjun Zhang ◽  
Fuyan Lyu ◽  
Xiushan Tang ◽  
Yang Yang ◽  
Xiaodong Ji ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Dynamic Properties ◽  
Single Point ◽  
Element Model ◽  
Rotary Table ◽  
Cutting Head ◽  
Cutting System ◽  
The Finite Element Model ◽  
Intense Vibration

The intense vibration of a roadheader rotary table damages the cutting system of the roadheader and reduces the efficiency. This paper analyzes the vibration of a rotary table by combining the finite element model with tested data from an underground coalmine. First, the force of the rotary table during the cutting procedure was analyzed, and the finite element model was built using Pro/E and ADAMS. The tested data were then imported into the model after selection, procession, and combination were conducted. Next, the six lowest-order parameters of the rotary table were calculated. A vibration analysis of the rotary table under certain working conditions was conducted, and the results were compared with those from a modal experiment using a single-point excitation method. According to the comparison between the simulation result and experiments, it is clear that this method is both reasonable and feasible. And it could supplement the theoretical foundation of the analysis of other roadheader components, providing reference for the improvement of the structure and dynamic properties of a roadheader. In addition, other vibration components of a roadheader such as the cutting head and the cutting arm could also be analyzed through the proposed method, with very reliable precision.

Study on Modal Analysis for Motorcycle Frame by CAE Method

2014 ◽  
Vol 496-500 ◽  
pp. 601-604
Author(s):  
Jing Wang ◽  
Yong Wang ◽  
Ying Hua Liao
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Modal Analysis ◽  
Experimental Method ◽  
Dynamic Properties ◽  
Element Model ◽  
Analytic Method ◽  
Motorcycle Frame ◽  
The Finite Element Model ◽  
Good Agreement

In this paper, the modal of motorcycle frame is analyzed by using the analytic method and experimental method. The results show that the dynamic properties of the finite element model are in good agreement with the experiment and the finite element model was reliable and accurate.

Dynamic Test and Analysis of Concrete Filled Steel Tube Arch Bridge

2010 ◽  
Vol 163-167 ◽  
pp. 2843-2847
Author(s):  
Li Xian Wang ◽  
Sheng Kui Di
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Yellow River ◽  
Dynamic Properties ◽  
Dynamic Test ◽  
Element Model ◽  
Steel Tube ◽  
Acceleration Signal ◽  
The Finite Element Model

Based on random vibration theory, virtual response is obtained from the measured acceleration signal of Yantan Yellow River Bridge of Lanzhou under ambient excitation, Yantan Yellow River bridge's modal parameters were identified by using the peak picking and stochastic subspace identification, analyzed from theoretical and experimental aspects, compared with the finite element model results and verified the reliability of recognition results. The identified dynamic properties can be served as the basis in the finite element model updating, damage detection, condition assessment and health monitoring of the bridge.

scholarly journals A Review of Research on Human-induced Vibration Serviceability and Dynamic Properties of Long-span Floor

2018 ◽  
Vol 38 ◽  
pp. 03012
Author(s):  
Li Lin Cao ◽  
Cheng Qian ◽  
Lan Zhe Chu ◽  
Guo Jun Yu
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Field Test ◽  
Model Test ◽  
Dynamic Properties ◽  
Element Model ◽  
Long Span ◽  
Vibration Serviceability ◽  
The Finite Element Model

Studies on the dynamic properties of long-span floor is an essential basis for a solution to the problem of human-induced vibration serviceability. According to the recent research, this review introduces the application of numerical simulation in the research of dynamic properties and summarizes the modeling method of sophisticated finite element model. The reliability of the finite element model is verified by the field test and model test. Comparing the application of studies on dynamic properties among numerical simulation and model test, the differences between numerical simulation and model test are summarized. Finally, some problems that need further study are proposed.

scholarly journals Sensitivity Analysis of the Influence of Structural Parameters on Dynamic Behaviour of Highly Redundant Cable-Stayed Bridges

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
B. Asgari ◽  
S. A. Osman ◽  
A. Adnan
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Structural Parameters ◽  
Element Model ◽  
Structural Behavior ◽  
Model Tuning ◽  
The Finite Element Model ◽  
Cable Stayed Bridges

The model tuning through sensitivity analysis is a prominent procedure to assess the structural behavior and dynamic characteristics of cable-stayed bridges. Most of the previous sensitivity-based model tuning methods are automatic iterative processes; however, the results of recent studies show that the most reasonable results are achievable by applying the manual methods to update the analytical model of cable-stayed bridges. This paper presents a model updating algorithm for highly redundant cable-stayed bridges that can be used as an iterative manual procedure. The updating parameters are selected through the sensitivity analysis which helps to better understand the structural behavior of the bridge. The finite element model of Tatara Bridge is considered for the numerical studies. The results of the simulations indicate the efficiency and applicability of the presented manual tuning method for updating the finite element model of cable-stayed bridges. The new aspects regarding effective material and structural parameters and model tuning procedure presented in this paper will be useful for analyzing and model updating of cable-stayed bridges.

Biodynamics of Human Thorax With Body Armors Subject to Bullet Impact

2001 ◽  
Author(s):  
Y. W. Kwon ◽  
J. A. Lobuono
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Body Armor ◽  
Projectile Impact ◽  
Human Thorax ◽  
Trachea And Bronchi ◽  
Armor System ◽  
The Finite Element Model

Abstract The objective of this study is to develop a finite element model of the human thorax with a protective body armor system so that the model can adequately determine the thorax’s biodynamical response from a projectile impact. The finite element model of the human thorax consists of the thoracic skeleton, heart, lungs, major arteries, major veins, trachea, and bronchi. The finite element model of the human thorax is validated by comparing the model’s results to experimental data obtained from cadavers wearing a protective body armor system undergoing a projectile impact.

Dynamic Analysis of a Turbocharger Centrifugal Compressor Impeller

1991 ◽  
Author(s):  
V. Ramamurti ◽  
D. A. Subramani ◽  
K. Sridhara
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Centrifugal Compressor ◽  
Element Model ◽  
Simplified Model ◽  
Cyclic Symmetry ◽  
Compressor Impeller ◽  
Cyclic Symmetric ◽  
The Finite Element Model

Abstract Stress analysis and determination of eigen pairs of a typical turbocharger compressor impeller have been carried out using the concept of cyclic symmetry. A simplified model treating the blade and the hub as isolated elements has also been attempted. The limitations of the simplified model have been brought out. The results of the finite element model using the cyclic symmetric approach have been discussed.

Analysis of Effective Pre-Stress of Continuous Rigid Frame Bridge in Service Based on Inversion Theory

2013 ◽  
Vol 671-674 ◽  
pp. 1012-1015
Author(s):  
Zhao Ning Zhang ◽  
Ke Xing Li
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Inversion Method ◽  
Vertical Deflection ◽  
Continuous Rigid Frame Bridge ◽  
Rigid Frame ◽  
Inversion Theory ◽  
Rigid Frame Bridge ◽  
The Finite Element Model

Due to the environment, climate, loads and other factors, the pre-stress applied to the beam is not a constant. It is important for engineers to track the state of the pre-stress in order to ensure security of the bridge in service. To solve the problem mentioned above, the paper puts forward a new way to analyze the effective pre-stress using the displacement inversion method based on the inversion theory according to the measured vertical deflection of the bridge in service at different time. The method is a feasible way to predict the effective pre-stress of the bridge in service. Lastly, taking the pre-stressed concrete continuous rigid frame bridge for example, the effective pre-stress is analyzed by establishing the finite element model.

scholarly journals Physical Principles of a Piezo Accelerometer Sensitive to a Nearly Constant Signal

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3258 ◽  
Author(s):  
Valery Gupalov ◽  
Alexander Kukaev ◽  
Sergey Shevchenko ◽  
Egor Shalymov ◽  
Vladimir Venediktov
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Frequency Band ◽  
Linear Acceleration ◽  
High Sensitivity ◽  
Element Model ◽  
Wide Frequency Band ◽  
Piezoelectric Accelerometer ◽  
The Finite Element Model ◽  
Physical Principles

The paper considers the construction of a piezoelectric accelerometer capable of measuring constant linear acceleration. A number of designs are proposed that make it possible to achieve high sensitivity with small dimensions and a wide frequency band (from 10−5 Hz). The finite element model of the proposed design was investigated, and its output characteristic and scale factor (36 mV/g) were obtained.

Analysis on sealing performance of VL seals based on mixed lubrication theory

2019 ◽  
Vol 71 (1) ◽  
pp. 54-60 ◽  
Author(s):  
Shixian Xu ◽  
Zhengtao Su ◽  
Jian Wu
Keyword(s):  
Finite Element ◽  
Film Thickness ◽  
Finite Element Model ◽  
Friction Factor ◽  
Contact Pressure ◽  
Element Model ◽  
Mixed Lubrication ◽  
Content Type ◽  
Deformation Mechanics ◽  
The Finite Element Model

Purpose This paper aims to research the influence of pressure, friction factors, roughness and actuating speed to the mixed lubrication models of outstroke and instroke. Design/methodology/approach Mixed lubrication model is solved by finite volume method, which consists of coupled fluid mechanics, deformation mechanics and contact mechanics analyses. The influence of friction factor on the finite element model is also considered. Then, contact pressure, film thickness, friction and leakage have been studied. Findings It was found that the amount of leakage is sensitive to the film thickness. The larger the film thickness is, the greater the influence received from the friction factor, however, the effect of oil film on the friction is negligible. The friction is determined mainly by the contact pressure. The trend of friction and leakage influenced by actuating velocity and roughness is also obtained. Originality/value The influence of friction factor on the finite element model is considered. This can make the calculation more accurate.

Sign in / Sign up

Export Citation Format

Share Document