scholarly journals Structure, Mechanical Performance, and Dimensional Stability of Radiata Pine (Pinus radiata D. Don) Scrimbers

2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Jinguang Wei ◽  
Fei Rao ◽  
Yuxiang Huang ◽  
Yahui Zhang ◽  
Yue Qi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Pinus Radiata ◽  
Dimensional Stability ◽  
High Performance ◽  
Water Resistance ◽  
Mechanical Performance ◽  
Three Dimensional ◽  
Radiata Pine ◽  
Specific Strength ◽  
Shearing Strength

Natural wood has certain advantages such as good processability and high specific strength and thus has been used for millennium as a structural material. But the mechanical performance and water resistance, particularly for fast-growing species, are unsatisfactory for high-end applications. In this study, the “new-type” scrimber technology was introduced to radiata pine (Pinus radiata D. Don) scrimbers. The structure, mechanical properties, and dimensional stability of the scrimber panels were investigated. Results showed that OWFMs as basic units of scrimber had been very even in size and superior permeability. The scrimbers exhibited a three-dimensional porous structure, and the porosity had a decrease with increasing density. Both OWFMs and densification contributed to the high performance in terms of mechanical properties and water resistance. The flexural, compressive, and short-beam shearing strength were significantly enhanced with increasing density. As the density was 0.80 g cm−3, the flexural strength (MOR) was approximately 120 MPa, much larger than many selected wood-based panels. Moreover, the water resistance and dimensional stability also were closely related to the density. At the density of 1.39 g cm−3, the water absorption rate and thinness swelling rate of the panels in boiled water were only 19% and 5.7%, respectively.

scholarly journals 3D Printing of High Viscosity Reinforced Silicone Elastomers

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2239
Author(s):  
Nicholas Rodriguez ◽  
Samantha Ruelas ◽  
Jean-Baptiste Forien ◽  
Nikola Dudukovic ◽  
Josh DeOtte ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
New Technologies ◽  
Three Dimensional ◽  
High Viscosity ◽  
Layer By Layer ◽  
Silicone Elastomers ◽  
Uv Curable ◽  
Octet Truss ◽  
Tunable Mechanical Properties

Recent advances in additive manufacturing, specifically direct ink writing (DIW) and ink-jetting, have enabled the production of elastomeric silicone parts with deterministic control over the structure, shape, and mechanical properties. These new technologies offer rapid prototyping advantages and find applications in various fields, including biomedical devices, prosthetics, metamaterials, and soft robotics. Stereolithography (SLA) is a complementary approach with the ability to print with finer features and potentially higher throughput. However, all high-performance silicone elastomers are composites of polysiloxane networks reinforced with particulate filler, and consequently, silicone resins tend to have high viscosities (gel- or paste-like), which complicates or completely inhibits the layer-by-layer recoating process central to most SLA technologies. Herein, the design and build of a digital light projection SLA printer suitable for handling high-viscosity resins is demonstrated. Further, a series of UV-curable silicone resins with thiol-ene crosslinking and reinforced by a combination of fumed silica and MQ resins are also described. The resulting silicone elastomers are shown to have tunable mechanical properties, with 100–350% elongation and ultimate tensile strength from 1 to 2.5 MPa. Three-dimensional printed features of 0.4 mm were achieved, and complexity is demonstrated by octet-truss lattices that display negative stiffness.

Morphology of Rigid-Rod Molecular Composites: An Overview

1988 ◽  
Vol 134 ◽  
Author(s):  
Stephen J. Krause
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Morphological Characterization ◽  
High Ratio ◽  
Structure Property ◽  
Chain Polymer ◽  
Specific Strength ◽  
Composite Systems ◽  
Molecular Composites ◽  
Rigid Rod

ABSTRACTRigid-rod molecular composites are a new class of high performance structural polymers which have high specific strength and modulus and also high thermal and environmental resistance. A rigid-rod, extended chain polymer component is used to reinforce a matrix of a ductile polymer with the intent of achieving a “composite” on the molecular level. After synthesis, the key to producing a molecular composite is to control morphology to disperse the reinforcing rod molecules as finely as possible in the matrix polymer. Individual rod molecules or bundles of molecular rods must have dimensions which result in a high ratio of length to width (aspect ratio) for efficient reinforcement. To achieve this, the reinforcing rod component must not phase separate at any stage of processing. Morphological characterization techniques, which can measure the orientation and dispersion (or, conversely, the degree of phase separation) of rod molecules provide the tools for correlating theoretically predicted and experimentally observed mechanical properties. Various morphological techniques which have been applied to molecular composite systems will be reviewed, including wide angle x-ray scattering and scanning and transmission electron microscopy. Structure-property correlations for molecular composite systems will be discussed with regard to models for mechanical properties. Application of new morphological techniques will also be discussed.

scholarly journals Enhancement of the physical and mechanical properties of wood using a novel organo-montmorillonite/hyperbranched polyacrylate emulsion

Holzforschung ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Jianfeng Xu ◽  
Xiaoyan Li ◽  
Ling Long ◽  
Ru Liu
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Pinus Radiata ◽  
Wood Sample ◽  
Wood Cell Wall ◽  
Physical And Mechanical Properties ◽  
Radiata Pine ◽  
Compact Structure ◽  
Populus Cathayana ◽  
Modified Wood

AbstractIn this work, a novel waterborne hyperbranched polyacrylate (HBPA) dispersed organo-montmorillonite (OMMT) emulsion was synthesized and used for the treatment of wood in a vacuum environment in order to enhance the physical and mechanical properties of the wood. The sapwood of Cathay poplar (Populus cathayana Rehd.) and Radiata pine (Pinus radiata D.Don) were used as the samples for experimentation. The results showed that the physical and mechanical properties of the wood improved significantly due to the successful penetration of the OMMT and HBPA into the wood cell wall. From it was also observed that OMET completely exfoliated from the HBPA matrix and formed a hydrophobic film covering on the inside walls of the cell lumen. Further, it was observed that the poplar sample displayed better mechanical properties than the pine sample because the pine has a more compact structure when compared to poplar and contains rosin. Furthermore, it was also observed that the mechanical properties of the modified wood sample gradually improved with an increase in the concentration of the emulsion. However, excessive concentration (>4 wt%) did not lead to further improvement.

Improvement of water resistance, dimensional stability, and mechanical properties of poplar wood by rosin impregnation

2015 ◽  
Vol 74 (2) ◽  
pp. 177-184 ◽  
Author(s):  
Youming Dong ◽  
Yutao Yan ◽  
Kaili Wang ◽  
Jianzhang Li ◽  
Shifeng Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dimensional Stability ◽  
Water Resistance ◽  
Poplar Wood

scholarly journals Characterisation of a High-Performance Al–Zn–Mg–Cu Alloy Designed for Wire Arc Additive Manufacturing

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1610 ◽  
Author(s):  
Paulo J. Morais ◽  
Bianca Gomes ◽  
Pedro Santos ◽  
Manuel Gomes ◽  
Rudolf Gradinger ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
High Performance ◽  
Mechanical Performance ◽  
Fluorescence Analysis ◽  
Cold Metal Transfer ◽  
Direction Parallel ◽  
X Ray ◽  
Wire Arc Additive Manufacturing

Ever-increasing demands of industrial manufacturing regarding mechanical properties require the development of novel alloys designed towards the respective manufacturing process. Here, we consider wire arc additive manufacturing. To this end, Al alloys with additions of Zn, Mg and Cu have been designed considering the requirements of good mechanical properties and limited hot cracking susceptibility. The samples were produced using the cold metal transfer pulse advanced (CMT-PADV) technique, known for its ability to produce lower porosity parts with smaller grain size. After material simulations to determine the optimal heat treatment, the samples were solution heat treated, quenched and aged to enhance their mechanical performance. Chemical analysis, mechanical properties and microstructure evolution were evaluated using optical light microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray fluorescence analysis and X-ray radiography, as well as tensile, fatigue and hardness tests. The objective of this research was to evaluate in detail the mechanical properties and microstructure of the newly designed high-performance Al–Zn-based alloy before and after ageing heat treatment. The only defects found in the parts built under optimised conditions were small dispersed porosities, without any visible cracks or lack of fusion. Furthermore, the mechanical properties are superior to those of commercial 7xxx alloys and remarkably independent of the testing direction (parallel or perpendicular to the deposit beads). The presented analyses are very promising regarding additive manufacturing of high-strength aluminium alloys.

Three-Dimensional Graphite Filled Poly(Vinylidene Fluoride) Composites with Enhanced Strength and Thermal Conductivity

2020 ◽  
Vol 842 ◽  
pp. 63-68
Author(s):  
Xiao Zhang ◽  
Jian Zheng ◽  
Yong Qiang Du ◽  
Chun Ming Zhang
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Energetic Materials ◽  
High Performance ◽  
Vinylidene Fluoride ◽  
3D Structure ◽  
Three Dimensional ◽  
3D Network ◽  
Poly Vinylidene Fluoride ◽  
Polymer Bonded Explosives

Three-dimensional (3D) network structure has been recognized as an efficient approach to enhance the mechanical and thermal conductive properties of polymeric composites. However, it has not been applied in energetic materials. In this work, a fluoropolymer based composite with vertically oriented and interconnected 3D graphite network was fabricated for polymer bonded explosives (PBXs). Here, the graphite and graphene oxide platelets were mixed, and self-assembled via rapid freezing and using crystallized ice as the template. The 3D structure was finally obtained by freezing-dry, and infiltrating with polymer. With the increasing of filler fraction and cooling rate, the thermal conductivity of the polymer composite was significantly improved to 2.15 W m-1 K-1 by 919% than that of pure polymer. Moreover, the mechanical properties, such as tensile strength and elastic modulus, were enhanced by 117% and 563%, respectively, when the highly ordered structure was embedded in the polymer. We attribute the increased thermal and mechanical properties to this 3D network, which is beneficial to the effective heat conduction and force transfer. This study supports a desirable way to fabricate the strong and thermal conductive fluoropolymer composites used for the high-performance polymer bonded explosives (PBXs).

Effect of Zr Diffusion Barrier Properties on the Irradiation Performance of U-10Mo Monolithic Fuel Plate

2019 ◽  
Author(s):  
Walid Mohamed ◽  
Hakan Ozaltun ◽  
Hee Seok Roh
Keyword(s):  
Mechanical Properties ◽  
Diffusion Barrier ◽  
High Performance ◽  
Mechanical Performance ◽  
Plate Thickness ◽  
Barrier Properties ◽  
Element Analysis ◽  
Uranium Fuel ◽  
High Enrichment ◽  
Irradiation Performance

Abstract The most recent design of U-Mo monolithic fuel as adopted by the U.S. for the conversion of its High Performance Research Reactors (USHPRR) from high enrichment uranium (HEU) to low enrichment uranium fuel (LEU, < 20% U235) consists of a high density (LEU) U-10Mo fuel sandwiched between Zirconium (Zr) diffusion barriers and encapsulated in aluminum (AA6061) cladding. In this work, finite element analysis (FEA) was used to evaluate effect of Zr diffusion barrier properties on the thermal and mechanical performance of a U-10Mo monolithic fuel plate by considering possible variation in thermal and mechanical properties of the Zr diffusion barrier. Possible variation in thermo-mechanical properties of the Zr diffusion barrier were determined and a simulation matrix was designed accordingly. Analyses of simulation results included determination of global peak stresses in the fuel, Zr diffusion barrier, and cladding sections as well as the plate thickness profile at a transverse section toward the top side of the plate. Results showed that variation in yield stress, elastic modulus and thermal conductivity of the Zr diffusion barrier has negligible effect on the thermal and mechanical performance of the monolithic fuel plate. The effect of variation in these properties was found to be limited to the barrier section itself, which may be attributed to the relatively smaller thickness of that section compared to the fuel and cladding sections of the fuel plate.

scholarly journals Quantifying High-Performance Material Microstructure Using Nanomechanical Tools with Visual and Frequency Analysis

Scanning ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Emil Sandoz-Rosado ◽  
Michael R. Roenbeck ◽  
Kenneth E. Strawhecker
Keyword(s):  
Mechanical Properties ◽  
Frequency Analysis ◽  
Visual Processing ◽  
High Performance ◽  
Mechanical Performance ◽  
Structure Property ◽  
Spatially Resolved ◽  
Macro Scale ◽  
Organization Strategy ◽  
Stiffness Scanning

High-performance materials like ballistic fibers have remarkable mechanical properties owing to specific patterns of organization ranging from the molecular scale, to the micro scale and macro scale. Understanding these strategies for material organization is critical to improving the mechanical properties of these high-performance materials. In this work, atomic force microscopy (AFM) was used to detect changes in material composition at an extremely high resolution with transverse-stiffness scanning. New methods for direct quantification of material morphology were developed, and applied as an example to these AFM scans, although these methods can be applied to any spatially-resolved scans. These techniques were used to delineate between subtle morphological differences in commercial ultra-high-molecular-weight polyethylene (UHMWPE) fibers that have different processing conditions and mechanical properties as well as quantify morphology in commercial Kevlar®, a high-performance material with an entirely different organization strategy. Both frequency analysis and visual processing methods were used to systematically quantify the microstructure of the fiber samples in this study. These techniques are the first step in establishing structure-property relationships that can be used to inform synthesis and processing techniques to achieve desired morphologies, and thus superior mechanical performance.

scholarly journals Enhancing the Capillary Force of Binder-Jetting Printing Ti6Al4V and Mechanical Properties under High Temperature Sintering by Mixing Fine Powder

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1354
Author(s):  
Yang Tang ◽  
Zheguan Huang ◽  
Jianming Yang ◽  
Yonglin Xie
Keyword(s):  
Mechanical Properties ◽  
Capillary Force ◽  
High Performance ◽  
Three Dimensional ◽  
Fine Powder ◽  
Green Body ◽  
Mixed Powder ◽  
Powder Bed ◽  
Polymer Binders

Binder jet 3D printing (BJ3DP) is an additive manufacturing technology that selectively deposits binder on powder to form a three-dimensional green body followed by sintering process. The low strength of green body and metallurgical issues limit the manufacture of Ti6Al4V parts with high-performance and that are lightweight. In this study, thermal-bubble inkjet technology was used to print Ti6Al4V parts via jetting low-concentration in-situ polymer binders. In addition, a method for mixing fine powder was used to enhance the capillary force of the powder bed and mechanical properties of the parts. The results show that the capillary force was enhanced from 8.35 kPa for pure powder to 16.27 kPa for mixed powder by mixing fine powder. The compression strength of green body was enhanced from 1.5 MPa to 3.21 MPa. After sintering, the sample with mixed powder sintered at 1420 °C for 2 h had achieved a maximum density of 95.2%, microhardness of 316 HV, and yield stress of 589 MPa. The relative density of 95.2% of Ti6Al4V parts fabricated by BJ3DP technology in our study is significantly higher than the value reported in the existing literature. Finally, the porous structure with a size of 550 μm was fabricated. Results presented demonstrate that BJ3DP can produce Ti6Al4V parts with excellent properties.

Sign in / Sign up

Export Citation Format

Share Document