scholarly journals Experimental Investigation on Shear Strength and Liquefaction Potential of Rubber-Sand Mixtures

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Zhou Enquan ◽  
Wang Qiong
Keyword(s):  
Shear Strength ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Construction Materials ◽  
Horizontal Displacement ◽  
Triaxial Tests ◽  
Hyperbolic Model ◽  
Liquefaction Potential ◽  
Direct Shear Tests ◽  
Rubber Particles

The application of scrap tires as construction materials in civil engineering is one of the most promising ways to recycle this pollutant. The objective of this study was to investigate the shear strength and liquefaction potential of saturated rubber-sand mixtures. Direct shear tests and cyclic triaxial tests were conducted on rubber-sand mixtures at various rubber contents. It was found that the addition of rubber particles to sand changed the shear stress-horizontal displacement development. The addition of rubber particles to sand improved the shear strength slightly and improved resistance to liquefaction significantly. Additionally, a hyperbolic model was proposed to describe the pore water pressure generation. This study demonstrates the effect of rubber particles on the physical properties of sand.

EXPERIMENT STUDY ON DYNAMIC STRENGTH OF LOESS UNDER REPEATED LOAD

2008 ◽  
Vol 22 (31n32) ◽  
pp. 5825-5830 ◽  
Author(s):  
ZHENGHUA XIAO ◽  
BO HAN ◽  
HONGJIAN LIAO ◽  
AKENJIANG TUOHUTI
Keyword(s):  
Shear Strength ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Dynamic Strength ◽  
Triaxial Tests ◽  
Dynamic Shear ◽  
Anisotropic Consolidation ◽  
Dynamic Shear Strength

A series of dynamic triaxial tests are performed on normal anisotropic consolidation and over anisotropic consolidation specimens of loess. Based on the test results, the variable regularity of dynamic shear stress, axial strain and pore water pressure of loess under dynamic loading are measured and analyzed. The influences of the dynamic shear strength and pore water pressure at different over consolidation ratio are analyzed. The relationship between dynamic shear strength and over consolidation ratio of loess is obtained. The evaluating standard of dynamic shear strength of loess is discussed. Meanwhile, how to determine the effective dynamic shear strength index of normal anisotropic consolidated loess is also discussed in this paper. Several obtained conclusions can be referenced for studying the dynamic shear strength of loess foundation.

scholarly journals Evaluation of Sand-Shell Mixture Behaviour for Breakwater Foundation

2016 ◽  
Author(s):  
Abbass Tavallali ◽  
Justine Mollaert
Keyword(s):  
Internal Friction ◽  
Relative Density ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Triaxial Tests ◽  
Direct Shear Tests ◽  
Different Depths ◽  
Sand Material

The available sand material for a breakwater foundation is mixed with shells. The shell percentage of the sand material is variable and percentages up to even 50% are observed. It is essential to evaluate the properties and the behaviour of the sand-shell mixture as this will form the improved breakwater foundation. In reality the backfilled sand of the breakwater foundation has different relative densities in different depths. In this study the mechanical properties of the sand-shell mixture for different relative densities are evaluated. For different relative densities of sand-shell mixture the direct shear tests and the consolidated undrained triaxial tests are carried out on some samples. The results of the experiments showed that the samples with higher relative density show a higher internal friction angle. However, for the samples with even low relative density, an internal friction angle of less than 32° is not observed. The volume variation of the samples with different relative densities are monitored. Samples with low relative density showed a contraction behaviour; resulting in an increase of the pore water pressure, a reduction of the effective strength and finally the samples become susceptible to liquefaction. While the samples with high relative density showed a dilatancy behaviour.

The Mexico Earthquake of September 19, 1985—General Soil Conditions and Clay Properties in the Valley of Mexico

1988 ◽  
Vol 4 (4) ◽  
pp. 731-752 ◽  
Author(s):  
M. P. Romo ◽  
A. Jaime ◽  
D. Reséndiz
Keyword(s):  
Shear Modulus ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Damping Ratio ◽  
Free Field ◽  
Elastic Behavior ◽  
Triaxial Tests ◽  
Soil Conditions ◽  
Hyperbolic Model ◽  
Lake Zone

We present and discuss the results of resonant column and cyclic triaxial tests on clay samples obtained from different sites within the Lake zone in the Valley of Mexico. Of particular interest are the nearly elastic behavior and low damping ratio even for shear strain amplitudes as high as 0.3 (%). A hyperbolic model reproduces adequately well the resulting shear modulus vs strain curves. Degradation of shear modulus caused by load repetition is negligible for strains lower than about 1 (%) but increases significantly for higher strains. A power-type expression fits well the modulus degradation vs number of cycles curves. Results from static triaxial tests indicate that for compression stress paths the induced pore water pressure is uniquely related to axial strains. Analyses of ground motions show that one dimensional wave propagation models may be used to predict free field seismic motions in most parts of the Lake zone.

scholarly journals Shear strength characteristics of a sand clay liner

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Muawia Dafalla ◽  
Abdullah Shaker ◽  
Tamer Elkady ◽  
Abdullah Almajed ◽  
Mosleh Al-Shamrani
Keyword(s):  
Shear Strength ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Clay Content ◽  
Triaxial Tests ◽  
High Plasticity ◽  
Content Increase ◽  
Triaxial Cell

Abstract This study investigated shear strength behaviour of compacted sand–clay mixtures used as liners, with 10%, 20%, and 30% clay contents. A natural high-plasticity and highly expansive clay found in the eastern province of Saudi Arabia was used. A series of consolidated undrained triaxial tests and pore water pressure measurements of saturated samples with various clay contents and confining pressures was conducted using a computer-controlled Bishop and Wesley triaxial cell. The unit was equipped with pressure volume controllers and a pressure transducer for measuring sample volume changes and excess pore water pressure. The experimental test results indicate that clay content and confining pressure significantly affect stress strain response curves, pore water pressure generation curves, and steady-state shear strength. Sand–clay mixtures with clay content less than 10% showed a tendency toward contractive behaviour. The failure line slope increased in accordance with clay content increase. The deviator stress versus axial strain of saturated sand–clay mixtures indicated a hyperbolic trend. The stress ratio versus axial strain representation was more informative for the shear strength behaviour assessment. Clay content did not significantly affect critical-state friction angle. Scanning electron microscope images of the sand-clay mixtures with different clay contents are presented.

Shear strength of a compacted residual soil from consolidated drained and constant water content triaxial tests

2004 ◽  
Vol 41 (3) ◽  
pp. 421-436 ◽  
Author(s):  
Harianto Rahardjo ◽  
Ong Boo Heng ◽  
Leong Eng Choon
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Pore Water ◽  
Volume Change ◽  
Triaxial Test ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Tests ◽  
Residual Soil ◽  
Undrained Conditions

Rainfall-induced landslides in unsaturated residual soils can occur slowly under drained conditions or rapidly under undrained conditions. Consolidated drained (CD) and constant water content (CW) tests have been performed to simulate the stress paths followed by soil elements in a slope that fails under drained and undrained conditions. The study was carried out to investigate the shear strength characteristics of soils associated with rainfall-induced slope failures. The soil tested was residual soil from the Jurong sedimentary formation and was reconstituted using static compaction. The test results indicate that the shear strength of the compacted specimens obtained from the CW tests agrees well with the shear strength obtained from the CD tests for the specimens with initial matric suctions less than their air-entry values. The shear strength results from the CD and CW triaxial tests start to differ when the matric suction exceeds the air-entry value of the soil. The CD and CW triaxial tests also indicate that the compacted specimens behave as a normally consolidated soil at matric suctions below the air-entry value of the soil and as an overconsolidated soil at matric suctions above the air-entry value of the soil. Results of the CW triaxial tests show that the relationship between the response of pore-water pressure and the total volume change of the specimen is more complicated than that found in the saturated undrained triaxial tests. In other words, the change in pore-water pressure during shearing is not directly related to the overall volume change of the specimen.Key words: unsaturated soil, compacted soil, residual soil, consolidated drained triaxial test, constant water content triaxial test.

Conjectures, Hypotheses, and Theories of Drumlin Formation (In memory of Stanislaw Baranowski)

1981 ◽  
Vol 27 (97) ◽  
pp. 503-505 ◽  
Author(s):  
Ian J. Smalley
Keyword(s):  
Shear Strength ◽  
Pore Water ◽  
Stress Level ◽  
Critical Stress ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Glacial Till ◽  
Forming Process ◽  
Stress Levels

AbstractRecent investigations have shown that various factors may affect the shear strength of glacial till and that these factors may be involved in the drumlin-forming process. The presence of frozen till in the deforming zone, variation in pore-water pressure in the till, and the occurrence of random patches of dense stony-till texture have been considered. The occurrence of dense stony till may relate to the dilatancy hypothesis and can be considered a likely drumlin-forming factor within the region of critical stress levels. The up-glacier stress level now appears to be the more important, and to provide a sharper division between drumlin-forming and non-drumlin-forming conditions.

Study on Artificial Island Ground Improvement Method and Effect

2014 ◽  
Vol 1030-1032 ◽  
pp. 1037-1040
Author(s):  
Jin Fang Hou ◽  
Ju Chen ◽  
Jian Yu
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Ground Improvement ◽  
Soft Soil ◽  
Horizontal Displacement ◽  
Treatment Method ◽  
Surcharge Preloading ◽  
Porosity Ratio ◽  
Improvement Method ◽  
Consolidation Degree

The artificial island ground on an open sea is covered by thick soft soil. It must be improved before using. In accordance with a designing scheme, the ground treatment method is inserting drain boards on land and jointed dewatering surcharge preloading, the residual settlement is not more than 30cm after improvement and the average consolidation degree is more than 85%. In order to estimate ground improvement effect and construction safety, instruments are buried to monitor the whole ground improving processes. By monitoring settlement and pore water pressure, it is shown that the total ground settlement in construction is 2234mm, its final settlement is 2464mm, and consolidation degree and residual settlement respectively satisfy requirements. In ground improvement, horizontal displacement is small and construction is safe. Meanwhile, the results of soil properties and vane shear strength detection tests show the soft soil ground is greatly reduced in water content and porosity ratio, and improved in strength. It is named that the ground improvement method is reasonable and reaches expected effect.

Prediction of liquefaction potential and pore water pressure beneath machine foundations

2014 ◽  
Vol 4 (3) ◽  
Author(s):  
Mohammed Fattah ◽  
Mohammed Al-Neami ◽  
Nora Jajjawi
Keyword(s):  
Pore Water ◽  
Sandy Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soil Liquefaction ◽  
Elastic Model ◽  
Liquefaction Resistance ◽  
Overburden Pressure ◽  
Liquefaction Potential ◽  
Frequency Changes

AbstractThe present research is concerned with predicting liquefaction potential and pore water pressure under the dynamic loading on fully saturated sandy soil using the finite element method by QUAKE/W computer program. As a case study, machine foundations on fully saturated sandy soil in different cases of soil densification (loose, medium and dense sand) are analyzed. Harmonic loading is used in a parametric study to investigate the effect of several parameters including: the amplitude frequency of the dynamic load. The equivalent linear elastic model is adopted to model the soil behaviour and eight node isoparametric elements are used to model the soil. Emphasis was made on zones at which liquefaction takes place, the pore water pressure and vertical displacements develop during liquefaction. The results showed that liquefaction and deformation develop fast with the increase of loading amplitude and frequency. Liquefaction zones increase with the increase of load frequency and amplitude. Tracing the propagation of liquefaction zones, one can notice that, liquefaction occurs first near the loading end and then develops faraway. The soil overburden pressure affects the soil liquefaction resistance at large depths. The liquefaction resistance and time for initial liquefaction increase with increasing depths. When the frequency changes from 5 to 10 rad/sec. (approximately from static to dynamic), the response in displacement and pore water pressure is very pronounced. This can be attributed to inertia effects. Further increase of frequency leads to smaller effect on displacement and pore water pressure. When the frequency is low; 5, 10 and 25 rad/sec., the oscillation of the displacement ends within the period of load application 60 sec., while when ω = 50 rad/sec., oscillation continues after this period.

Studying the Geotechnical Properties of Clayey Soil Contaminated by Kerosene

2020 ◽  
Vol 857 ◽  
pp. 383-393
Author(s):  
Mahdi O. Karkush ◽  
Amer G. Jihad
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Contaminated Soil ◽  
Fine Particles ◽  
Clayey Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Chemical Characteristics ◽  
Coefficient Of Consolidation ◽  
Plastic Containers

This study focuses on investigating the impacts of kerosene on the physical, mechanical, and chemical characteristics of clay soil. The soils specimens are contaminated artificially with six ratios of kerosene (5, 10, 20, 30, 40, and 50) % calculated according to the dry weight of soil. The artificial contamination includes air drying of the disturbed soil, then placed in plastic containers and mixed with the field water content and the specified concentration of kerosene to ensure getting homogenous contaminated soil specimens. The contaminated soil specimens left for 30 days in plastic containers covered by nylon sheets to control the water content and prevent volatility of contaminant. The results of tests proved that different ratios of kerosene have different impacts on the engineering and chemical characteristics of soil specimens. The specific gravity, percentages of fine particles, optimum water content, the initial and final void ratio, coefficient of consolidation, swelling index, permeability, the undrained shear strength, effective shear strength parameters, and the rate of reduction of initial pore water pressure are reduced significantly with increasing the content of kerosene in soil. Generally, the concentration of kerosene less than 10% has slight impacts on the studied characteristics of soil specimens.

Sign in / Sign up

Export Citation Format

Share Document