scholarly journals Stress Distribution and Fluctuation Cycle on the Rack Face of the Rock Cutting Tool

2019 ◽  
Vol 2019 ◽  
pp. 1-13
Author(s):  
Xiaofeng Yang ◽  
Yongchao Xue ◽  
Jiaheng Zhou
Keyword(s):  
Cutting Tool ◽  
Cutting Speed ◽  
Local Stress ◽  
Rock Cutting ◽  
Impact Factors ◽  
Cycle Period ◽  
Cutting Depth ◽  
Stress Fluctuation ◽  
Dynamic Simulation Model ◽  
Back Angle

The distribution of the stress field on the rack face has significant impacts on the performance and service life of the rock cutting tool. A dynamic simulation model of the stress on the rock cutting tool is established by finite element code Abaqus, and the distribution of local stress on the rack face and its impact factors are studied. It is concluded that the local stress on the rack face of the rock cutting tool shows obvious periodical fluctuation characteristics, and the fluctuation cycle of each point on the tool remains unchanged under the same cutting conditions. The stress fluctuation cycle period decreases with the increase of cutting speed inversely. The cutting depth and the back angle of the cutting tool have no obvious impact on the stress fluctuation period. However, the cutting depth and the back angle have obvious impacts on the average stress distributions of each point on the rack face of the tool. That is, the increase of back angle and cutting depth could cause the maximum stress point of the rack face to move upward to the tool tip.

scholarly journals Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1 to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

Experimental Research on Dry Cutting 34CrNiMo6

2011 ◽  
Vol 188 ◽  
pp. 319-324
Author(s):  
Hao Yang ◽  
Xi Bin Wang ◽  
Li Jing Xie ◽  
J.J. Pei ◽  
T. Wang
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Dry Cutting ◽  
Cutting Tool Wear ◽  
Ceramic Cutting Tool ◽  
Carbide Cutting Tool

By dry cutting 34CrNiMo6, hard-machined material, with carbide cutting tool and ceramic cutting tool, experimental analysis was carried out in tool wear and cutting force. Cutting tool wear in the process is researched in order to obtain the cutting tool wear patterns and analyze the influencing factors. Meanwhile, it is found that the cutting force with the cutting parameters (cutting speed, cutting depth, feed) changes regularly, and then the experience formula of cutting force can be established.

scholarly journals 3D Finite Element Analysis of Cutting Forces in the Process of Machining Rectangular Microchannels

2014 ◽  
Vol 8 (1) ◽  
pp. 726-730
Author(s):  
Zhanshu He ◽  
Dalei Li ◽  
Lianduo Cao ◽  
Xuefei Yang
Keyword(s):  
Cutting Forces ◽  
Cutting Tool ◽  
Thrust Force ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
3D Fem ◽  
Element Analysis ◽  
Rectangular Microchannels ◽  
Side Face

In the process of machining rectangular microchannels, severe friction occurs between the chip and the side face of the machined microchannel. The cutting forces have great effect on the miniature cutting tool. Thus, 3D FEM is adopted to study the cutting forces. The influences of the depth of the machined microchannel t, the cutting depth ac, the cutting width aw , the rake angle ○o and the cutting speed ν on the cutting forces are investigated. Results show that the main cutting force Fz and the thrust force Fy increase with the increase of t, ac and aw and have no obvious change with ν. Moreover, Fz decreases and Fy increases as γ○ increases.

Experimental investigation of a slip-line field model for a worn cutting tool

2013 ◽  
Vol 228 (8) ◽  
pp. 1398-1404 ◽  
Author(s):  
Alper Uysal ◽  
Erhan Altan
Keyword(s):  
Wear Rate ◽  
Slip Line ◽  
Field Model ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Rake Angle ◽  
Uncut Chip Thickness ◽  
Line Field

In this study, the slip-line field model developed for orthogonal machining with a worn cutting tool was experimentally investigated. Minimum and maximum values of five slip-line angles ( θ1, θ2, δ2, η and ψ) were calculated. The friction forces that were caused by flank wear land, chip up-curl radii and chip thicknesses were calculated by solving the model. It was specified that the friction force increased with increase in flank wear rate and uncut chip thickness and it decreased a little with increase in cutting speed and rake angle. The chip up-curl radius increased with increase in flank wear rate and it decreased with increase in uncut chip thickness. The chip thickness increased with increase in flank wear rate and uncut chip thickness. Besides, the chip thickness increased with increase in rake angle and it decreased with increase in cutting speed.

The Application of FEA in High-Speed Cutting

2011 ◽  
Vol 287-290 ◽  
pp. 104-107
Author(s):  
Lian Qing Ji ◽  
Kun Liu
Keyword(s):  
High Speed ◽  
Feeding Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Material Model ◽  
Friction Model ◽  
Cutting Depth ◽  
High Speed Cutting ◽  
Key Technologies

The history and application of the FEA are briefly presented in this paper. Several key technologies such as the building of material model, the establishment of the chip - tool friction model as well as meshing are described. Taking the high-speed cutting of titanium alloy (Ti - 10V - 2Fe - 3Al) as an example , reasonable cutting tools and cutting parameters are determinted by simulating the influences of cutting speed, cutting depth and feeding rate on the cutting parameters using FEA.

An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool

2014 ◽  
Vol 800-801 ◽  
pp. 237-240
Author(s):  
Li Fu Xu ◽  
Ze Liang Wang ◽  
Shu Tao Huang ◽  
Bao Lin Dai
Keyword(s):  
Experimental Study ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Cbn Tool ◽  
Cutting Experiment ◽  
Rough Turning

In this paper, the cutting experiment was used to study the influence of various cutting parameters on cutting force when rough turning titanium alloy (TC4) with the whole CBN tool. The results indicate that among the cutting speed, feed rate and cutting depth, the influence of the cutting depth is the most significant on cutting force; the next is the feed rate and the cutting speed is at least.

Deep Hole Machining with a Small Diameter Drill and Ultrasonic Vibration

2017 ◽  
Vol 749 ◽  
pp. 107-110
Author(s):  
Yuta Masu ◽  
Tomohito Fukao ◽  
Taiga Yasuki ◽  
Masahiro Hagino ◽  
Takashi Inoue
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Small Diameter ◽  
Maximum Amplitude ◽  
Depth Of Cut ◽  
Deep Hole ◽  
Work Material ◽  
Finished Surface

The method of imparting ultrasonic vibration to the cutting tool is known to improve the shape accuracy and finished surface roughness. However, a uniform evaluation of this function in drilling has not been achieved, and the cutting process cannot be checked from the outside. The aim of this study is to investigate the cutting characteristics in deep hole drilling when an ultrasonic vibrator on the table of a machining center provides vibration with a frequency of 20 kHz to the work piece. The ultrasonic vibrations in this system reach the maximum amplitude in the center of the work material. We evaluated the change in finished surface roughness between the section where drilling starts to the point of maximum amplitude with ultrasonic vibration. The main cutting conditions are as follows: cutting speed (V) 12.6 (mm/min); feed rate (s) 30, 60 (mm/rev); depth of cut (t) = 32 (mm); work material, tool steel; cutting tool material, HSS; point angle (σ) 118 (°); and drill diameter (φ) 4 (mm). Lubricant powder was also added to clarify the cutting effect, and compared the condition in which there was no ultrasonic vibration. The results showed that surface roughness at the point of maximum amplitude was better than that with no vibration.

scholarly journals Numerical Simulation of Rock Plate Cutting with Three Sides Fixed and One Side Free

2018 ◽  
Vol 2018 ◽  
pp. 1-21 ◽  
Author(s):  
Zhenguo Lu ◽  
Lirong Wan ◽  
Qingliang Zeng ◽  
Xin Zhang ◽  
Kuidong Gao
Keyword(s):  
Numerical Simulation ◽  
Cutting Force ◽  
Cutting Speed ◽  
Rock Cutting ◽  
Numerical Results ◽  
Peak Force ◽  
Cutting Performance ◽  
Conical Pick ◽  
Cutting Method ◽  
Cutting Angle

In order to overcome conical pick wear in the traditional rock cutting method, a new cutting method was proposed on account of increasing free surface of the rock. The mechanical model of rock plate bending under concentrated force was established, and the first fracture position was given. The comparison between experimental and numerical results indicated that the numerical method is effective. A computer code LS-DYNA (3D) was employed to study the cutting performance of a conical pick. To study the rock size influenced on the cutting performance, the numerical simulations with different thickness, width, and height of a rock plate was carried out. The numerical simulation with the different cutting parameters of cutting speed, cutting angle, and cutting position influenced on cutting performance was also carried out. The numerical results indicated that the peak force increased with the increasing thickness of rock plate. With the increasing width and height of the rock plate, the peak force decreased and then became stable. Besides, the peak force decreased with the increasing of cutting position lxp/lx. Moreover, the peak force increased and then decreased with the increasing of cutting angle. The cutting speed has nonsignificant influence on the peak force. The strong exponential relationship was obtained between the peak force and cutting position, thickness, height, and width of the rock plate at a confidence level of 0.95. A binomial relationship was observed between the peak force and cutting angel. The cutting force comparison between traditional rock cutting and rock plate cutting indicated that the new cutting method can effectively reduce peak cutting force.

Sign in / Sign up

Export Citation Format

Share Document