scholarly journals Numerical Simulation on Cutting and Fracturing of Rock Plate with One Side Fixed and Three Sides Free

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Zhenguo Lu ◽  
Qingliang Zeng ◽  
Zhaosheng Meng ◽  
Zhiwen Wang ◽  
Guanshun Gao
Keyword(s):  
Numerical Simulation ◽  
Cutting Force ◽  
Cutting Tool ◽  
Hard Rock ◽  
Rock Fracture ◽  
Rock Fragment ◽  
Conical Pick ◽  
Cutting Angle ◽  
Saw Blade ◽  
Element Erosion

Conical pick is a rock cutting tool that is commonly used in roadway driving. Pick wear frequently happens in the course of breaking hard rock. The current paper shows a new method to solve the problem of pick wear. The rock is preslit with the saw blade and then broken by the conical pick. In order to study the cutting force and features of rock fragment, the numerical model is built between rock plate and conical pick. And element erosion is added in the code to obtain the fracture result. The rock plate cutting testbed is made to testify the correctness of numerical simulation. The width, height, and thickness of the rock plate, as well as cutting angle and cutting position, which influence cutting force and rock fracture are studied. According to the results, there exist exponential relationships between cutting force and width and thickness of rock plate. In addition, a linear relationship is found between the cutting force and the height of rock plate. Furthermore, both the cutting angle and cutting depth have an influence on cutting force. In particular, the factors of thickness and height or rock plate have the most obvious influence on cutting force. It is proven that what is beneficial to rock fracture is higher height and lower thickness of rock plate.

scholarly journals Numerical Simulation of Rock Plate Cutting with Three Sides Fixed and One Side Free

2018 ◽  
Vol 2018 ◽  
pp. 1-21 ◽  
Author(s):  
Zhenguo Lu ◽  
Lirong Wan ◽  
Qingliang Zeng ◽  
Xin Zhang ◽  
Kuidong Gao
Keyword(s):  
Numerical Simulation ◽  
Cutting Force ◽  
Cutting Speed ◽  
Rock Cutting ◽  
Numerical Results ◽  
Peak Force ◽  
Cutting Performance ◽  
Conical Pick ◽  
Cutting Method ◽  
Cutting Angle

In order to overcome conical pick wear in the traditional rock cutting method, a new cutting method was proposed on account of increasing free surface of the rock. The mechanical model of rock plate bending under concentrated force was established, and the first fracture position was given. The comparison between experimental and numerical results indicated that the numerical method is effective. A computer code LS-DYNA (3D) was employed to study the cutting performance of a conical pick. To study the rock size influenced on the cutting performance, the numerical simulations with different thickness, width, and height of a rock plate was carried out. The numerical simulation with the different cutting parameters of cutting speed, cutting angle, and cutting position influenced on cutting performance was also carried out. The numerical results indicated that the peak force increased with the increasing thickness of rock plate. With the increasing width and height of the rock plate, the peak force decreased and then became stable. Besides, the peak force decreased with the increasing of cutting position lxp/lx. Moreover, the peak force increased and then decreased with the increasing of cutting angle. The cutting speed has nonsignificant influence on the peak force. The strong exponential relationship was obtained between the peak force and cutting position, thickness, height, and width of the rock plate at a confidence level of 0.95. A binomial relationship was observed between the peak force and cutting angel. The cutting force comparison between traditional rock cutting and rock plate cutting indicated that the new cutting method can effectively reduce peak cutting force.

scholarly journals Numerical Simulation of Conical Pick Cutting Arc Rock Plate Fracture Based on ANSYS/LS-DYNA

2020 ◽  
Vol 2020 ◽  
pp. 1-16 ◽  
Author(s):  
Zhiwen Wang ◽  
Qingliang Zeng ◽  
Zhenguo Lu ◽  
Lirong Wan ◽  
Xin Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Cutting Force ◽  
Structural Parameters ◽  
Cutting Parameters ◽  
Rock Breaking ◽  
Central Axis ◽  
Plate Height ◽  
Conical Pick ◽  
Cutting Angle ◽  
Cutting Point

The new method of rock breaking based on the combination of circular sawblade and conical pick was proposed to improve the effectiveness of hard rock breaking. The numerical simulation method was applied to research the conical pick cutting arc rock plate by ANSYS/LS-DYNA. The conical pick cutting arc rock plate numerical simulation model was established to research the influence of arc rock plate structural parameters and cutting parameters on cracks formation and propagation of the arc rock plate and the cutting force in the process of conical pick cutting arc rock plate. The amount of cracks is positively correlated with arc rock plate thickness, the cutting speed, and distance of cutting point to arc rock plate central axis and negatively correlated with the cutting angle. The mean peak cutting force is positively correlated with the thickness of arc rock plate and the distance of cutting point to arc rock plate central axis; however, it is negatively correlated with the arc rock plate height and width and cutting angle of conical pick. The simulation results can be used to predict the conical pick work performance with various cutting parameters and structural parameters.

scholarly journals Research on Cutting Characteristics of Rock Plate with Two Sides Fixed and Two Sides Free

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Zhenguo Lu ◽  
Qingliang Zeng ◽  
Zhihai Liu ◽  
Guanshun Gao ◽  
Peisi Zhong
Keyword(s):  
Compressive Strength ◽  
Cutting Force ◽  
Uniaxial Compressive Strength ◽  
Fracture Morphology ◽  
Theoretical Research ◽  
Cutting Depth ◽  
Conical Pick ◽  
Rock Fragments ◽  
Saw Blade ◽  
Two Sides

Conical pick wear is an urgent problem in the roadway excavation caused by hard rock difficult to break. The traditional method of increasing cutting power to improve cutting performance of conical pick significantly increases pick wear. In the paper, a saw blade and conical pick combined cutting method is proposed based on increased free surface. To research the fracture morphology and cutting force of rock plate, theoretical, numerical, and experimental methods are used. By theoretical research, the bending mechanical model of rock plate bending is established. The cutting position and the junction between the free sides and fixed sides are preferentially broken. A numerical model combining the erosion and damage constitutive model is built, and the cutting process of rock plate was presented. According to rock plate experiment, the peak cutting force increases with the increasing uniaxial compressive strength, thickness of rock plate, and cutting depth of conical pick and decreases with the increasing width and height of rock plate. Exponential relationships exist between peak cutting force and thickness, width and height of rock plate, and cutting depth of conical pick. Linear relationship exists between peak cutting force and uniaxial compressive strength. The size of rock fragments increases with uniaxial compressive strength, width, and height of rock plate.

scholarly journals Rock Breaking by Conical Pick Assisted with High Pressure Water Jet

2014 ◽  
Vol 6 ◽  
pp. 868041 ◽  
Author(s):  
Liu Songyong ◽  
Chen Junfeng ◽  
Liu Xiaohui
Keyword(s):  
Numerical Simulation ◽  
High Pressure ◽  
Hard Rock ◽  
Rock Breaking ◽  
Water Jet ◽  
Cutting Efficiency ◽  
Conical Pick ◽  
Pressure Water ◽  
High Pressure Water Jet ◽  
Better Than

In the process of hard rock breaking, the conical pick bears great cutting force and wear, and the cutting efficiency is lower. Thus different combination ways of water jet and conical pick were proposed to solve this issue; for instance, water jet placed in the front of pick (JFP) and water jet through the center of pick (JCP) was researched by numerical simulation and experiments in this paper. First, the models of rock breaking were built based on SPH combined with finite element method. Then, the stress distribution of rock and the cut force of pick were analyzed when the rock broken by the conical pick assisted with the high pressure water jet. It indicates that the effect of the JCP on rock breaking is better than the JFP. At last, experiments about rock breaking with a conical pick and the JCP were conducted to verify the reliability of the simulation. It indicates that the rock breaking with the assistance of high pressure water jet cannot only reduce the pick force, but also increase the rock crushing volume.

A method for numerical simulation based on microseismic information and the interpretation of hard rock fracture

2019 ◽  
Vol 164 ◽  
pp. 214-224 ◽  
Author(s):  
Chunchi Ma ◽  
Tianbin Li ◽  
Hang Zhang ◽  
Yupeng Jiang ◽  
Tao Song
Keyword(s):  
Numerical Simulation ◽  
Hard Rock ◽  
Rock Fracture ◽  
Simulation Based

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

High-Speed Capturing of Stress Distribution of Workpiece under Ultrasonically Assisted Cutting Condition

2014 ◽  
Vol 1017 ◽  
pp. 747-752
Author(s):  
Hiromi Isobe ◽  
Keisuke Hara
Keyword(s):  
Stress Distribution ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Light Emission ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Photoelastic Method ◽  
Intermittent Cutting ◽  
Ultrasonic Vibration Cutting

This paper reports the stress distribution inside the workpiece under ultrasonic vibration cutting (UVC) condition. Many researchers have reported the improvement of tool wear, burr generation and surface integrity by reduction of time-averaged cutting force under UVC condition. However general dynamometers have an insufficient frequency band to observe the processing phenomena caused by UVC. In this paper, stress distribution inside the workpiece during UVC was observed by combining the flash light emission synchronized with ultrasonically vibrating cutting tool and the photoelastic method. Instantaneous stress distribution during UVC condition was observed. Because UVC induced an intermittent cutting condition, the stress distribution changed periodically and disappeared when the tool leaved from the workpiece. It was found that instantaneous maximum cutting force during UVC condition was smaller than quasi-static cutting force during conventional cutting when the cutting speed was less than 500 mm/min.

scholarly journals Preparation and cutting performance of nano-scaled Al2O3-coated micro-textured cutting tool prepared by atomic layer deposition

2021 ◽  
Vol 40 (1) ◽  
pp. 77-86
Author(s):  
Siwen Tang ◽  
Pengfei Liu ◽  
Zhen Su ◽  
Yu Lei ◽  
Qian Liu ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Atomic Layer Deposition ◽  
Cutting Force ◽  
Cutting Tool ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Atomic Layer ◽  
Cutting Performance ◽  
Cutting Test ◽  
Layer Deposition

Abstract Al2O3 nano-scaled coating was prepared on micro-textured YT5 cemented carbide cutting tools by atomic layer deposition ALD. The effect of Al2O3 nano-scaled coating, with and without combined action of texture, on the cutting performance was studied by orthogonal cutting test. The results were compared with micro-textured cutting tool and YT5 cutting tool. They show that the micro-texture and nano-scaled Al2O3 coated on the micro-texture both can reduce the cutting force and friction coefficient of the tool, and the tools with nano-scaled Al2O3 coated on the micro-texture are more efficient. Furthermore, the friction coefficient of the 100 nm Al2O3-coated micro-texture tool is relatively low. When the distance of the micro-pits is 0.15 mm, the friction coefficient is lowest among the four kinds of pit textured nanometer coating tools. The friction coefficient is the lowest when the direction of the groove in strip textured nanometer coating tool is perpendicular to the main cutting edge. The main mechanism of the nanometer Al2O3 on the micro-textured tool to reduction in cutting force and the friction coefficient is discussed. These results show that the developed tools effectively decrease the cutting force and friction coefficient of tool–chip interface.

Sign in / Sign up

Export Citation Format

Share Document