scholarly journals Understanding the Role of Metakaolin towards Mitigating the Shrinkage Behavior of Alkali-Activated Slag

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6962
Author(s):  
Bo Fu ◽  
Zhenyun Cheng ◽  
Jingyun Han ◽  
Ning Li
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Activator Concentration ◽  
Reaction Products ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated ◽  
Shrinkage Behavior

This research investigates the mechanism of metakaolin for mitigating the autogenous and drying shrinkages of alkali-activated slag with regard to the activator parameters, including concentration and modulus. The results indicate that the incorporation of metakaolin can decrease the initial viscosity and setting time. Increasing activator concentration can promote the reaction process and shorten the setting time. An increase in the metakaolin content induces a decrease in compressive strength due to reduced formation of reaction products. However, increasing activator dosage and modulus can improve the compressive strength of alkali-activated slag containing 30% metakaolin. The inclusion of metakaolin can mitigate the autogenous and drying shrinkage of alkali-activated slag by coarsening the pore structure. On the other hand, increases in activator concentration and modulus result in an increase in magnitude of the autogenous and drying shrinkage of alkali-activated slag containing metakaolin. The influence of the activator modulus on the shrinkage behavior of alkali-activated slag-metakaolin binary system should be further investigated.

scholarly journals Effect of Dosage of Alkaline Activator on the Properties of Alkali-Activated Slag Pastes

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang
Keyword(s):  
Compressive Strength ◽  
Room Temperature ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Engineering Properties ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Good Workability ◽  
Alkali Activated

This study focused on the engineering properties of alkali-activated slag (AAS) pastes prepared by mixing an activator consisting of sodium silicate and sodium hydroxide at room temperature. The water-to-slag ratio of AAS paste was kept constant at 0.35 by mass. AAS pastes were prepared using the activator with five different silicate moduli of 1, 1.2, 1.4, 1.6, and 1.8 and three different Na2O contents of 6%, 8%, and 10%. The results showed that both the silicate moduli and Na2O contents had significant effects on the engineering properties of AAS pastes. All the AAS pastes exhibited properties such as fast setting, good workability, and high early compressive strength. The final setting time varied from 9 to 36 min, and the fluidity was in the range of 147–226 mm. The 1 d compressive strength of all the AAS pastes, which could be easily achieved, had values above 55 MPa, whereas the highest strength obtained was 102 MPa with the silicate modulus of 1 and Na2O content of 8% at room temperature. The drying shrinkage increased as the silicate modulus increased. Furthermore, the hydration products and microstructures of AAS pastes were explained according to the microanalysis methods.

scholarly journals Pottery Sand as Fine Aggregate for Preparing Alkali-Activated Slag Mortar

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang
Keyword(s):  
Compressive Strength ◽  
Mechanical Performance ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Sodium Oxide ◽  
Oxide Content ◽  
Fine Aggregate ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated

Alkali-activated slag (AAS) mortars were prepared using pottery sand as a fine aggregate in a ratio of 1 : 1.75 using a blend of sodium silicate and NaOH as an alkaline activator at room temperature. The effects of sodium oxide content and silicate moduli on the setting time, fluidity, consistency, compressive strength, and drying shrinkage of different AAS mortars were determined. These results revealed that sodium oxide content and silicate modulus had little effect on the setting time and workability of the mortar; however, they did have a significant effect on their mechanical performance and drying shrinkage levels. All the AAS mortars exhibited faster setting times, better workability, and higher early and late compressive strength compared to traditional mortars. Optimum compressive strength was achieved at 93 and 123 MPa after 1 d and 28 d, respectively, using a silicate modulus of 1.2 and Na2O content of 8%. The microstructures of mortars were characterized using scanning electron microscopy with energy dispersive spectrometric (SEM/EDS) and mercury intrusion porosimetry (MIP). These results reveal that AAS mortars containing pottery sand as a fine aggregate may represent a promising building material with improved properties for use in the construction industry.

Experimental Study on Alkali-Activated Slag-Lithium Slag-Fly Ash Environmental Concrete

2011 ◽  
Vol 287-290 ◽  
pp. 1237-1240
Author(s):  
Lan Fang Zhang ◽  
Rui Yan Wang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Alkali Activated Slag ◽  
Percent Increase ◽  
Compressive Strength Of Concrete ◽  
Activated Slag ◽  
Lithium Slag ◽  
Alkali Activated

The aim of this paper is to study the influence of lithium-slag and fly ash on the workability , setting time and compressive strength of alkali-activated slag concrete. The results indicate that lithium-slag and fly-ash can ameliorate the workability, setting time and improve the compressive strength of alkali-activated slag concrete，and when 40% or 60% slag was replaced by lithium-slag or fly-ash, above 10 percent increase in 28-day compressive strength of concrete were obtained.

scholarly journals Effect of Sodium Aluminate Dosage as a Solid Alkaline Activator on the Properties of Alkali-Activated Slag Paste

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Chen ◽  
Jun Wang ◽  
Jinyou Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Sodium Aluminate ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated

Extensive research into alkali-activated slag as a green gel material to substitute for cement has been done because of the advantages of low-carbon dioxide emissions and recycling of industrial solid waste. Alkali-activated slag usually has good mechanical properties, but the too fast setting time restricted its application and promotion. Changing the composition of alkaline activator could optimize setting time, usually making it by adding sodium carbonate or sodium sulfate but this would cause insufficient hydration reaction power and hinder compressive strength growth. In this paper, the effect of sodium aluminate dosage as an alkaline activator on the setting time, fluidity, compressive strength, hydration products, and microstructures was studied through experiments. It is fair to say that an appropriate amount of sodium aluminate could obtain a suitable setting time and better compressive strength. Sodium aluminate provided enough hydroxyl ions for the paste to promote the hydration reaction process that ensured obtaining high compressive strength and soluble aluminium formed precipitate wrapped on the surface of slag to inhibit the hydration reaction process in the early phase that prolonged setting time. The hydration mechanism research found that sodium aluminate played a key role in the formation of higher cross-linked gel hydration products in the late phase of the process. Preparing an alkali-activated slag with excellent mechanical properties and suitable setting time will significantly contribute to its application and promotion.

scholarly journals Effect of Cr6+ on the Properties of Alkali-Activated Slag Cement

2021 ◽  
Vol 8 ◽  
Author(s):  
Fu Bo ◽  
Cheng Zhenyun
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Cement Stone ◽  
Slag Cement ◽  
Hydration Kinetics ◽  
Alkali Activated Slag ◽  
Dual Beam ◽  
Press Method ◽  
Activated Slag ◽  
Alkali Activated

In order to investigate the effect of Cr6+ on the properties of alkali-activated slag cement (AAS), the effects of added dosage of Na2Cr2O4 on the setting time and compressive strength of AAS were measured. The leaching concentration of Cr6+ from AAS cement stone was measured using dual-beam UV-visible spectrophotometry. The effect of Na2Cr2O4 on the hydration kinetics of AAS cement was monitored by microcalorimetry and the corresponding kinetic parameters were analyzed. The pore solution from AAS was collected and analyzed using the high pressure press method. The effects of Na2Cr2O4 on the hydration products of AAS cement were observed and compared using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The experimental results showed that the AAS hydration process was markedly affected by Na2Cr2O4 dosage. The setting time of AAS pastes was increased and the compressive strength of cement stones was reduced with increasing dosage of Na2Cr2O4. With the development of AAS hydration, the leaching concentration of Na2Cr2O4 gradually decreased. Na2Cr2O4 did not affect the dissolution of slag particles, but impeded the formation of C-S-H gel. The Cr6+ was immobilized chemically in the form of needle-like CaCrO4 particles formed by the chemical reaction between Na2Cr2O4 and Ca2+ leaching from the slag.

Shrinkage Behavior of Alkali-Activated Slag Cement Pastes

2018 ◽  
Vol 761 ◽  
pp. 45-48 ◽  
Author(s):  
Vladyslav Omelchuk ◽  
Guang Ye ◽  
Rayisa Runova ◽  
Igor I. Rudenko
Keyword(s):  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Chemical Shrinkage ◽  
Slag Cement ◽  
Cement Pastes ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Mineral Additives ◽  
Alkali Activated ◽  
Shrinkage Behavior

Nowadays, alkali-activated cements (AACs) are the most promising alternatives to ordinary portland cement (OPC). Such cements characterized by better strength and corrosion resistance that determine improved durability of materials based on them. However, the shrinkage of AAC systems is noticeably higher compared with OPC. The purpose of this work was to study the shrinkage behavior of alkali-activated slag cement (AASC) pastes. To improve early age performance of AASCs – OPC and Ca(OH)2, as mineral additives, were added to the designed cement mixtures. The properties, like, flexural and compressive strength of cement mortars, chemical shrinkage, autogenous shrinkage and drying shrinkage of cement pastes were studied. The results showed that the chemical shrinkage, autogenous shrinkage and drying shrinkage at 28 days were between 0.064 – 0.074 ml/g, 4.5 – 7.9 mm/m and 3.3 – 4.9 mm/m, respectively. The relationship between the nature of alkaline components, the type of mineral additives and the shrinkage behavior of cements were discussed.

scholarly journals Use of Industrial Waste Slag in Alkali-Activated Slag Ceramsite Concrete Hollow Blocks

2018 ◽  
Vol 8 (12) ◽  
pp. 2358 ◽  
Author(s):  
Zhenzhen Jiao ◽  
Ying Wang ◽  
Wenzhong Zheng ◽  
Wenxuan Huang ◽  
Xianyu Zhou
Keyword(s):  
Compressive Strength ◽  
Industrial Waste ◽  
Drying Shrinkage ◽  
Concrete Block ◽  
Na2o Content ◽  
Alkali Activated Slag ◽  
Viable Solution ◽  
Optimal Mix ◽  
Activated Slag ◽  
Alkali Activated

In this paper, a parametric experimental study developing the alkali-activated slag concrete hollow block (AASCHB) is discussed. Fourteen trial mixes of alkali-activated slag concrete containing pottery sand and ceramsite with different water-to-slag ratios, sand ratios, silicate moduli, and Na2O contents were evaluated to determine the optimal mix for high compressive strength and low drying shrinkage. All four factors evaluated were found to be significant for the desired properties. A series of 390 × 190 × 190 mm3 AASCHBs were prepared using the optimal mix with a water-to-slag ratio of 0.35, sand ratio of 0.64, silicate modulus of 1.2, and Na2O content of 8%. The compressive strength, flexural strength, water absorption, and moisture content tests of these blocks indicate that the resulting AASCHB can be classified under the strength grade of MU15 as a load-bearing hollow concrete block. The proposed AASCHBs appear to provide a viable solution to the environmental problems of industrial waste and cement production emissions, leading to more sustainable buildings without compromising structural performance.

scholarly journals Strength and Drying Shrinkage of Alkali-Activated Slag Paste and Mortar

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Mao-chieh Chi ◽  
Jiang-jhy Chang ◽  
Ran Huang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Portland Cement ◽  
Liquid Slag ◽  
Drying Shrinkage ◽  
Curing Temperature ◽  
Alkali Activated Slag ◽  
Cement Mortars ◽  
Activated Slag ◽  
Alkali Activated

The aim of this study is to investigate the strengths and drying shrinkage of alkali-activated slag paste and mortar. Compressive strength, tensile strength, and drying shrinkage of alkali-activated slag paste and mortar were measured with various liquid/slag ratios, sand/slag ratios, curing ages, and curing temperatures. Experimental results show that the higher compressive strength and tensile strength have been observed in the higher curing temperature. At the age of 56 days, AAS mortars show higher compressive strength than Portland cement mortars and AAS mortars with liquid/slag ratio of 0.54 have the highest tensile strength in all AAS mortars. In addition, AAS pastes of the drying shrinkage are higher than AAS mortars. Meanwhile, higher drying shrinkage was observed in AAS mortars than that observed comparable Portland cement mortars.

Shrinkage-Reducing Admixture Efficiency in Alkali-Activated Slag across the Different Doses of Activator

2018 ◽  
Vol 761 ◽  
pp. 19-22 ◽  
Author(s):  
Vlastimil Bílek Jr. ◽  
Lukáš Kalina ◽  
Ondřej Fojtík
Keyword(s):  
Compressive Strength ◽  
Drying Shrinkage ◽  
Strength Development ◽  
Alkali Activated Slag ◽  
Reducing Ability ◽  
Wide Range ◽  
Shrinkage Reducing Admixture ◽  
Negative Effect ◽  
Activated Slag ◽  
Alkali Activated

One of the largest obstacles for the wider use of alkali-activated slag (AAS) in a building industry is its severe drying shrinkage. According to some studies shrinkage-reducing admixtures (SRAs) could be a solution of this problem, but they were also reported to have a fatal impact on AAS hydration resulting in a serious strength development slowdown. The aim of this paper was to investigate this phenomenon in a wide range of the waterglass doses (4–12% Na2O of the slag mass). Mortars without and with 2% of SRA based on hexylene glycol were prepared and their shrinkage and compressive strength development was tested. By far the highest shrinkage reduction was observed for the lowest doses of waterglass, but these were also the cases of the highest compressive strength decrease. However, it is possible to suppress the negative effect of SRA on AAS strength development through the activator dose increase with certainly decreased shrinkage reducing ability of SRA.

Sign in / Sign up

Export Citation Format

Share Document