scholarly journals The transient stability analysis of wind turbines interconected to grid under fault

2020 ◽  
Vol 10 (1) ◽  
pp. 600
Author(s):  
Anass Gourma ◽  
Abdelmajid Berdai ◽  
Moussa Reddak
Keyword(s):  
Wind Turbine ◽  
Power Plants ◽  
Wind Farm ◽  
Transient Stability ◽  
Electricity Production ◽  
Synchronous Generators ◽  
Electricity Grid ◽  
Rotor Angle ◽  
The Stability ◽  
The Impact

Wind farm has been growing in recent years due to its very competitive electricity production cost. Wind generators have gone from a few kilowatts to megawatts. However, the participation of the wind turbine in the stability of the electricity grid is a critical point to check, knowing that the electricity grid is meshed, any change in active and reactive flux at the network level affects its stability. With a rate of 50% wind turbine penetration into the electricity grid, the stability of the rotor angle is a dynamic phenomenon which is only visible by the variation of the active energy. The purpose of this journal is to verify the impact of wind turbine integration on an electrical grid, by exploiting the relationship between the reactive energy produced by the Doubly Fed Induction Generator equipping most wind energy systems, and the stability of the rotor angle of the synchronous generators equipping the conventional power plants in the electrical system.

scholarly journals Contribution of FACTS Devices to the Transient Stability Improvement of a Power System Integrated with a PMSG-based Wind Turbine

2019 ◽  
Vol 9 (6) ◽  
pp. 4893-4900 ◽  
Author(s):  
N. E. Akpeke ◽  
C. M. Muriithi ◽  
C. Mwaniki
Keyword(s):  
Power System ◽  
Wind Turbine ◽  
Energy Demand ◽  
Wind Farm ◽  
Transient Stability ◽  
Transient State ◽  
Synchronous Generator ◽  
Test System ◽  
Synchronous Generators ◽  
Facts Devices

The increasing penetration of wind energy to the conventional power system due to the rapid growth of energy demand has led to the consideration of different wind turbine generator technologies. In fault conditions, the frequency of the power system decreases and eventually leads to speed differences between the grid and the interconnected wind generator. This can result to power system problems such as transient instability (TS). This paper focuses on enhancing the TS of a permanent magnet synchronous generator (PMSG)-based power system during 3ph fault conditions using FACTS devices. The power system considered is connected to a large wind farm which is based on PMSG. Critical clearing time (CCT) is used as an index to evaluate the transient state of the system. Under the study of an IEEE-14 bus system using PSAT as a simulation tool, the integrated CCT with PMSG-based wind turbine is improved with three independent FACTS devices. One of the synchronous generators in the test system has been replaced at random with the PMSG-based wind turbine which is meant to generate an equivalent power. Time domain simulations (TDSs) were carried out considering four study cases. Simulation results show that the (CCT) of the system with the FACTS devices is longer than the CCT without them, which is an indication of TS improvement.

scholarly journals Enhancement of Power System Transient Stability by the Coordinated Control between an Adjustable Speed Pumping Generator and Battery

2020 ◽  
Vol 10 (24) ◽  
pp. 9034
Author(s):  
Junji Tamura ◽  
Atsushi Umemura ◽  
Rion Takahashi ◽  
Atsushi Sakahara ◽  
Fumihito Tosaka ◽  
...  
Keyword(s):  
Power Systems ◽  
Power System ◽  
Wind Farm ◽  
Transient Stability ◽  
Wind Farms ◽  
System Stability ◽  
Synchronous Generators ◽  
Adjustable Speed ◽  
The Stability ◽  
Network Fault

The penetration level of large-scale wind farms into power systems has been increasing significantly, and the frequency stability and transient stability of the power systems during and after a network fault can be negatively affected. This paper proposes a new control method to improve the stability of power systems that are composed of large wind farms, as well as usual synchronous generators. The new method is a coordinated controlling method between an adjustable-speed pumping generator (ASG) and a battery. The coordinated system is designed to improve power system stability during a disconnection in a fixed-rotor-speed wind turbine with a squirrel cage-type induction generator (FSWT-SCIG)-based wind farm due to a network fault, in which a battery first responds quickly to the system frequency deviation due to a grid fault and improves the frequency nadir, and then the ASG starts to supply compensatory power to recover the grid frequency to the rated frequency. The performance of the proposed system was confirmed through simulation studies on a power system model consisting of usual synchronous generators (SGs), an ASG, a battery, and an SCIG-based wind farm. Simulation results demonstrated that the proposed control system can enhance the stability of the power system effectively.

scholarly journals Power System Stability Study on Multi Machine Systems having DFIG Based Wind Generation System

2020 ◽  
Vol 6 (3) ◽  
pp. 27-30
Author(s):  
Pramod Kumar Mehar ◽  
Mrs. Madhu Upadhyay
Keyword(s):  
Steady State ◽  
Power Systems ◽  
Power System ◽  
Power Plants ◽  
Transient Stability ◽  
Power System Stability ◽  
Stability Study ◽  
System Stability ◽  
Synchronous Generators ◽  
The Impact

Power system stability is related to principles of rotational motion and the swing equation governing the electromechanical dynamic behavior. In the special case of two finite machines the equal area criterion of stability can be used to calculate the critical clearing angle on the power system, it is necessary to maintain synchronism, otherwise a standard of service to the consumers will not be achieved. With the increasing penetration of doubly fed induction generators (DFIGs), the impact of the DFIG on transient stability attracts great attention. Transient stability is largely dominated by generator types in the power system, and the dynamic characteristics of DFIG wind turbines are different from that of the synchronous generators in the conventional power plants. The analysis of the transient stability on DFIG integrated power systems has become a very important issue. This paper is a review of three types of stability condition. The first type of stability, steady state stability explains the maximum steady state power and the power angle diagram. There are several methods to improve system stability in which some methods are explained.

Study on Transient Stability Simulation of District Grid Containing High Proportion of Wind Power

2014 ◽  
Vol 1070-1072 ◽  
pp. 275-278
Author(s):  
Li Lin ◽  
Shuang Zhao ◽  
Meng Ze Yu ◽  
Bo Jian Ding
Keyword(s):  
Wind Power ◽  
Power Plants ◽  
Large Scale ◽  
Wind Farm ◽  
Fault Location ◽  
Transient Stability ◽  
Thermal Power ◽  
Wind Farms ◽  
Operating Modes ◽  
The Impact

As wind is random, intermittent and instability, with continual installation of wind farms, the impact of large scale wind farm on power system has become an important issue for integration and operation of wind farm. Aiming at studying the transient stability of district grid containing high proportion of wind power, numerical simulations with BPA for an actual district grid of China Southern Power Grid are presented. In these simulations, the interaction between the large-scale wind farm and traditional thermal power plants (TPPs) is investigated taking the different operating modes and fault location into account. The critical clearing time (CCT) is adopted as the measurable indicator to assess the interaction.

scholarly journals Transient Stability Assessment of IEEE 9-Bus System Integrated Wind Farm

2021 ◽  
Vol 335 ◽  
pp. 02006
Author(s):  
Ahmad Adel Alsakati ◽  
Chockalingam Aravind Vaithilingam ◽  
Jamal Alnasseir
Keyword(s):  
Power System ◽  
Wind Energy ◽  
Alternative Energy ◽  
Power Plants ◽  
Wind Farm ◽  
Transient Stability ◽  
Load Flow ◽  
System Stability ◽  
The Stability ◽  
Bus System

The use of wind energy is increased due to the high demand for sustainable energy. The penetration of wind energy in electrical networks might have several effects on load flow and power system stability. In this research, the transient stability of the IEEE 9-Bus system integrated with Doubly Fed Induction Generator (DFIG) is analyzed. Additionally, different penetration levels of a wind farm are considered. With a 5% penetration of wind energy, the maximum power angle of the synchronous generator is around 129 deg, which is quite similar to the existing system. In contrast, the power angle increases to 140 deg after adding more wind turbines with 15% wind farm penetration. Then, the system loses stability with a 25% penetration of wind energy. The results indicate that the high penetration of wind energy has a destabilizing impact on the studied network. Moreover, the location of the wind farm affects transient stability. This research intends to contribute towards assessing the stability of the power system integrated DFIG. Hence, this study will support the increase of using wind energy in power systems rather than conventional power plants and evaluate the stability to enable the reliability of alternative energy sources in the grid.

scholarly journals WIND POWER PLANT FOR THE NEEDS OF SMALL AGRICULTURAL FACILITIES

2020 ◽  
pp. 116-121
Author(s):  
Vаsіly Kоrdоnsky
Keyword(s):  
Wind Energy ◽  
Low Power ◽  
Wind Turbine ◽  
Wind Power ◽  
Power Plants ◽  
Wind Farm ◽  
Electrical Energy ◽  
Advantages And Disadvantages ◽  
Wind Power Plants ◽  
The Impact

There are many advantages of wind energy, including energy, environmental, economic. Relatively low investment in wind energy projects compared to traditional energy industries. The total kinetic energy of wind in the world can be estimated as 80 times higher than the total energy consumption by humans. And although only a certain fraction of this total can be used for energy needs, the future. The development of the technology itself has enormous potential. The article introduces and provides a brief analysis and historical background of existing designs of low-power wind power plants of the world's major manufacturers; the purpose of research on the proposed topic is indicated. Proposed and developed and described a promising scheme of a wind farm for the needs of small agricultural facilities, which makes it possible to receive electric current at low wind speeds in all natural and climatic zones of Ukraine. It has been established that low-power wind power plants are one of the promising areas for obtaining electrical energy and meeting the needs for small agricultural facilities. The proposed scheme for generating electrical energy. This design of a wind turbine can produce both DC and AC power for stand-alone or grid systems. The calculation of the wind turbine rotor diameter has been reduced. The advantages and disadvantages of wind energy in comparison with traditional energy industries are described. Brief conclusions are made on the proposed design of the wind farm, this will improve the environment, reducing the impact of anthropogenic factors on the environment and also, taking into account the constant increase in energy prices, save money, since such independent small wind farms allow small agricultural facilities to be provided with energy sources.

scholarly journals Impact of the Wind Turbine on the Parameters of the Electricity Supply to an Agricultural Farm

2021 ◽  
Vol 13 (13) ◽  
pp. 7279
Author(s):  
Zbigniew Skibko ◽  
Magdalena Tymińska ◽  
Wacław Romaniuk ◽  
Andrzej Borusiewicz
Keyword(s):  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Rural Areas ◽  
Power Plants ◽  
Reactive Power ◽  
Supply Voltage ◽  
Common Source ◽  
Voltage Fluctuations ◽  
The Impact

Wind power plants are an increasingly common source of electricity located in rural areas. As a result of the high variability of wind power, and thus the generated power, these sources should be classified as unstable sources. In this paper, the authors attempted to determine the impact of wind turbine operation on the parameters of electricity supplied to farms located near the source. As a result of the conducted field tests, variability courses of the basic parameters describing the supply voltage were obtained. The influence of power plant variability on the values of voltage, frequency, and voltage distortion factor was determined. To estimate the capacity of the transmission lines, the reactive power produced in the power plant and its effect on the value of the power factor were determined. The conducted research and analysis showed that the wind power plant significantly influences voltage fluctuations in its immediate vicinity (the maximum value registered was close to 2%, while the value required by law was 2.5%). Although all the recorded values are within limits specified by the current regulations (e.g., the THD value is four times lower than the required value), wind turbines may cause incorrect operation of loads connected nearby. This applies mainly to cases where consumers sensitive to voltage fluctuations are installed in the direct vicinity of the power plant.

Wind Farm Grid Integration Simulation Analysis of the Impact of Power System Transient Stability

2013 ◽  
Vol 805-806 ◽  
pp. 334-337
Author(s):  
Shi Wei Su ◽  
You Wei Zhou ◽  
Wei Xiong
Keyword(s):  
Power System ◽  
Wind Farm ◽  
Transient Stability ◽  
Simulation Analysis ◽  
Direct Access ◽  
Grid Integration ◽  
Access System ◽  
Wind Dispersion ◽  
The Impact ◽  
Single Set

Analysis compares the direct access to a single set of wind power systemTwo groups of wind farm access system directlyMultiple sets of wind farm access system directly And Multiple sets of wind dispersion access system's impact on power system transient stability. And compare the simulation results, Concluded that wind farm access capacity and its topology structure's influence on system transient stability.

The CFD Design and Optimisation of a 100 kW Hydrogen Fuelled mGT

2020 ◽  
Author(s):  
Cedric Devriese ◽  
Gijs Penninx ◽  
Guido de Ruiter ◽  
Rob Bastiaans ◽  
Ward De Paepe
Keyword(s):  
Combustion Chamber ◽  
Power Plants ◽  
Internal Combustion Engines ◽  
Cone Angle ◽  
Electricity Production ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Large Power ◽  
Power Sources ◽  
The Impact

Abstract Against the background of a growing deployment of renewable electricity production, like wind and solar, the demand for energy storage will only increase. One of the most promising ways to cover the medium to long-term storage is to use the excess electricity to produce hydrogen via electrolysis. In a modern energy grid, filled with intermittent power sources and ever-increasing problems to construct large power plants in densely populated areas, a network of Decentralised Energy Systems (DES) seems more logical. Therefore, the importance of research into the design of a small to medium-sized hydrogen fuelled micro Gas Turbine (mGT) unit for efficient, local heat and electricity production becomes apparent. To be able to compete with Reciprocating Internal Combustion Engines (RICEs), the mGT needs to reach 40% electrical efficiency. To do so, there are two main challenges; the design of an ultra-low NOX hydrogen combustor and a high Turbine Inlet Temperature (TIT) radial turbine. In this paper, we report on the progress of our work towards that goal. First, an improvement of the initial single-nozzle swirler (swozzle) combustor geometry was abandoned in favour of a full CFD (steady RANS) design and optimisation of a micromix type combustion chamber, due to its advantages towards NOx-emission reduction. Second, a full CFD design and optimisation of the compressor and turbine is performed. The improved micromix combustor geometry resulted in a NOx level reduction of more than 1 order of magnitude compared to our previous swozzle design (from 1400 ppm to 250 ppm). Moreover, several design parameters, such as the position and diameter of the hydrogen injection nozzle and the Air Guiding Panel (AGP) height, have been optimized to improve the flow patterns. Next to the combustion chamber, CFD simulations of the compressor and turbine matched the 1D performance calculations and reached the desired performance goals. A CFD analysis of the impact of the tip gap and exhaust diffuser cone angle led to a choice of these parameters that improved the compressor and turbine performance with a limited loss in efficiency.

Sign in / Sign up

Export Citation Format

Share Document