Design the Balance of System of Photovoltaic for Low Load Application

2016 ◽  
Vol 4 (2) ◽  
pp. 279 ◽  
Author(s):  
Y.M. Irwan ◽  
Z. Syafiqah ◽  
A.R. Amelia ◽  
M. Irwanto ◽  
W.Z. Leow ◽  
...  
Keyword(s):  
Protection Device ◽  
Pv System ◽  
Battery Charge ◽  
Load Demand ◽  
Pv Module ◽  
Electricity Bill ◽  
Centre Of Excellence ◽  
Low Load ◽  
Protection Devices ◽  
To Receive

<p>This paper presents an alternative method to reduce the monthly electricity bill at Centre of Excellence for Renewable Energy (CERE) which is by installing a stand-alone photovoltaic (PV) system. In the stand-alone PV system, apart from the PV module and loads, other components in the system such as battery, charge controller, inverter and protection device are categorized under Balance of System (BOS) component. In order for the loads to receive adequate energy to operate, the overall system must be sized through calculations due to find the optimum combination. This sizing will determine the amount of each component that needed in the system. The hardware is setup in front of CERE building which located at Kangar, Perlis, Malaysia. As the results from the calculation, the system required 6 units of PV module, 5 units of battery and a 0.23 kW inverter. The cable and protection devices are from the calculation. The entire system was successfully installed and was able to support the load demand.</p>

scholarly journals Feasibility Study of the Technical and Economic Performance of Grid-Connected PV System for Selected Rooftops in UTHM

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Mohamad Fakrie Mohamad Ali ◽  
◽  
Mohd Noor Abdullah ◽  
Keyword(s):  
Feasibility Study ◽  
Crystalline Silicon ◽  
Electricity Consumption ◽  
Payback Period ◽  
Net Energy ◽  
Pv System ◽  
Pv Module ◽  
Electricity Bill ◽  
Pv Modules ◽  
Energy Metering

This paper presents the feasibility study of the technical and economic performances of grid-connected photovoltaic (PV) system for selected rooftops in Universiti Tun Hussein Onn Malaysia (UTHM). The analysis of the electricity consumption and electricity bill data of UTHM campus show that the monthly electricity usage in UTHM campus is very high and expensive. The main purpose of this project is to reduce the annual electricity consumption and electricity bill of UTHM with Net Energy Metering (NEM) scheme. Therefore, the grid-connected PV system has been proposed at Dewan Sultan Ibrahim (DSI), Tunku Tun Aminah Library (TTAL), Fakulti Kejuruteraan Awam dan Alam Bina (FKAAS) and F2 buildings UTHM by using three types of PV modules which are mono-crystalline silicon (Mono-Si), poly-crystalline silicon (Poly-Si) and Thin-film. These three PV modules were modeled, simulated and calculated using Helioscope software with the capacity of 2,166.40kWp, 2,046.20kWp and 1,845kWp respectively for the total rooftop area of 190,302.9 ft². The economic analysis was conducted on the chosen three installed PV modules using RETScreen software. As a result, the Mono-Si showed the best PV module that can produce 2,332,327.40 kWh of PV energy, 4.4% of CO₂ reduction, 9.3 years of payback period considering 21 years of the contractual period and profit of RM4,932,274.58 for 11.7 years after payback period. Moreover, the proposed installation of 2,166.40kWp (Mono-SI PV module) can reduce the annual electricity bill and CO2 emission of 3.6% (RM421,561.93) and 4.4% (1,851.40 tCO₂) compared to the system without PV system.

Performance assessment of free standing and building integrated grid connected photovoltaic system for southern part of India

2020 ◽  
pp. 014362442097774
Author(s):  
VS Chandrika ◽  
M Mohamed Thalib ◽  
Alagar Karthick ◽  
Ravishankar Sathyamurthy ◽  
A Muthu Manokar ◽  
...  
Keyword(s):  
Geographical Location ◽  
Photovoltaic System ◽  
Building Structures ◽  
System Efficiency ◽  
Pv System ◽  
Free Standing ◽  
Pv Module ◽  
Building Integrated Photovoltaic ◽  
Community Buildings ◽  
Equatorial Climate

Photovoltaic (PV) system efficiency depends on the geographical location and the orientation of the building. Until installing the building structures, the integration of the PV module must be evaluated with ventilation and without ventilation effects. This work optimises the performance of the 250 kWp grid-connected photovoltaic (GPV) for community buildings in the southern part of India. This simulation is carried out to evaluate the system efficiency of the GPV system under various ventilation conditions, such as free-standing PV (FSPV), building integrated photovoltaic ventilated (BIPV_V) and Building Integrated Photovoltaic without ventilation (BIPV). The PVsyst simulation tool is used to simulate and optimise the performance of the system with FSPV, BIPV and BIPV_V for the region of Chennai (13.2789° N, 80.2623° E), Tamilnadu, India. An annual system energy production is 446 MWh, 409 MWh and 428 MWh of FSPV, BIPV and BIPV_V system respectively. while electrical efficiency for the FSPV, BIPV_V, BIPV system is 15.45%. 15.25% and 14.75% respectively. Practical application: Integrating the grid connected photovoltaic system on the building reduces the energy consumption in the building. The integration of the PV on the roof or semi integrated on the roof is need to be investigated before installing on the buildings. The need for installation of the BIPV with ventilation is explored. This study will assist architects and wider community to design buildings roofs with GPV system which are more aesthetic and account for noise protection and thermal insulation in the region of equatorial climate zones.

scholarly journals Design of a Building-Integrated Photovoltaic System with a Novel Bi-Reflector PV System (BRPVS) and Optimal Control Mechanism: An Experimental Study

Electronics ◽  
2018 ◽  
Vol 7 (7) ◽  
pp. 119 ◽  
Author(s):  
Muhammad Khan ◽  
Kamran Zeb ◽  
Waqar Uddin ◽  
P. Sathishkumar ◽  
Muhammad Ali ◽  
...  
Keyword(s):  
Low Cost ◽  
Input Voltage ◽  
Photovoltaic System ◽  
Solar Pv ◽  
Pv System ◽  
Building Integrated Photovoltaics ◽  
Pv Module ◽  
Solar Pv System ◽  
Zero Carbon ◽  
The Cost

Environment protection and energy saving are the most attractive trends in zero-carbon buildings. The most promising and environmentally friendly technique is building integrated photovoltaics (BIPV), which can also replace conventional buildings based on non-renewable energy. Despite the recent advances in technology, the cost of BIPV systems is still very high. Hence, reducing the cost is a major challenge. This paper examines and validates the effectiveness of low-cost aluminum (Al) foil as a reflector. The design and the performance of planer-reflector for BIPV systems are analyzed in detail. A Bi-reflector solar PV system (BRPVS) with thin film Al-foil reflector and an LLC converter for a BIPV system is proposed and experimented with a 400-W prototype. A cadmium–sulfide (CdS) photo-resistor sensor and an Arduino-based algorithm was developed to control the working of the reflectors. Furthermore, the effect of Al-foil reflectors on the temperature of PV module has been examined. The developed LLC converter confirmed stable output voltage despite large variation in input voltage proving its effectiveness for the proposed BRPVS. The experimental results of the proposed BRPVS with an Al-reflector of the same size as that of the solar PV module offered an enhancement of 28.47% in the output power.

Effect of Unglazed Transpired Collector on the Performance of a Polycrystalline Silicon Photovoltaic Module

2006 ◽  
Vol 128 (3) ◽  
pp. 349-353 ◽  
Author(s):  
A. T. Naveed ◽  
E. C. Kang ◽  
E. J. Lee
Keyword(s):  
Polycrystalline Silicon ◽  
Electrical Power ◽  
Heating System ◽  
Photovoltaic Module ◽  
Forced Ventilation ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Typical Day ◽  
Electrical Output

The electrical power generated by a polycrystalline silicon photovoltaic (PV) module mounted on an unglazed transpired solar collector (UTC) has been studied and compared to that of a PV module without UTC for a quantitative analysis of electrical output and its role in reducing the simple payback periods of photovoltaic electrical systems. A 75W polycrystalline silicon PV module was fixed on an UTC in front of the ventilation fan, and effectiveness of cooling by means of the forced ventilation at the rate of 160CFM was monitored. The temperature reduction under forced ventilation was in the range of 3-9°C with a 5% recovery in the electrical output power on a typical day of the month of February 2005. The simulated and measured electrical power outputs are in reasonable agreement with root-mean-square error of 2.40. The life cycle assessment of a hypothetical PV system located at Daejeon, South Korea and consisting of 3kW PV modules fixed on a 50m2 UTC shows that with a possible reduction of 3-9°C in the operating temperatures, the system requires three 75W fewer PV modules. The simple payback period of PV system is reduced from 23yearsto15years when integrated into an UTC air heating system.

A dsPIC Microcontroller Based System Identification of Positive Output Buck Boost Converter for Module Mismatch Application

2015 ◽  
Vol 785 ◽  
pp. 106-110
Author(s):  
M.N.M. Hussain ◽  
Ahmad Maliki Omar ◽  
Intan Rahayu Ibrahim ◽  
Kamarulazhar Daud
Keyword(s):  
Direct Method ◽  
Low Cost ◽  
Digital Signal ◽  
Solar Irradiation ◽  
Identification System ◽  
Pv System ◽  
Partial Shading ◽  
Single Output ◽  
Pv Module ◽  
Power Point

An identification system of multiple-input single-output (MISO) model is developed in controlling dsPIC microcontroller of positive output buck-boost (POBB) converters for module mismatch condition of photovoltaic (PV) system. In particular, the possibility of the scheme is to resolve the mismatch losses from the PV module either during shading or mismatch module occurrences. The MPPT algorithm is simplified by identification approach of indirect incorporated with a simple incremental direct method to form a combined direct and indirect (CoDId) algorithms. Irregular consumption of solar irradiation on a PV module shall step-up or step down the voltage regarding to the desired DC output voltage of POBB converter. This optimized algorithm will ensure that the PV module to kept at maximum power point (MPP), preventing power loss during module mismatch incident in PV module especially during partial shading condition. The simulation and laboratory results for PV module of polycrystalline Mitsubishi PV-AE125MF5N indicate that the proposed model and development of PV system architecture performs well, while the efficiency up to 97.7% at critical of low solar irradiance level. The controlling signal is based on low-cost embedded microcontroller of dsPIC30F Digital Signal Control (DSC).

scholarly journals Modeling, Control and Power Management Strategy of a Grid connected Hybrid Energy System

2018 ◽  
Vol 8 (3) ◽  
pp. 1345 ◽  
Author(s):  
Sujit Kumar Bhuyan ◽  
Prakash Kumar Hota ◽  
Bhagabat Panda
Keyword(s):  
Fuel Cell ◽  
Power Management ◽  
Storage Tank ◽  
Power Flow ◽  
Management Strategies ◽  
Energy System ◽  
Pv System ◽  
Hybrid Energy System ◽  
Hybrid Energy ◽  
Load Demand

This paper presents the detailed modeling of various components of a grid connected hybrid energy system (HES) consisting of a photovoltaic (PV) system, a solid oxide fuel cell (SOFC), an electrolyzer and a hydrogen storage tank with a power flow controller. Also, a valve controlled by the proposed controller decides how much amount of fuel is consumed by fuel cell according to the load demand. In this paper fuel cell is used instead of battery bank because fuel cell is free from pollution. The control and power management strategies are also developed. When the PV power is sufficient then it can fulfill the load demand as well as feeds the extra power to the electrolyzer. By using the electrolyzer, the hydrogen is generated from the water and stored in storage tank and this hydrogen act as a fuel to SOFC. If the availability of the power from the PV system cannot fulfill the load demand, then the fuel cell fulfills the required load demand. The SOFC takes required amount of hydrogen as fuel, which is controlled by the PID controller through a valve. Effectiveness of this technology is verified by the help of computer simulations in MATLAB/SIMULINK environment under various loading conditions and promising results are obtained.

scholarly journals Photovoltaic Systems and Net Metering in Greece

2018 ◽  
Vol 8 (4) ◽  
pp. 3168-3171
Author(s):  
F. Mavromatakis ◽  
G. Viskadouros ◽  
H. Haritaki ◽  
G. Xanthos
Keyword(s):  
Net Present Value ◽  
Electricity Consumption ◽  
Electrical Energy ◽  
Internal Rate Of Return ◽  
Pv System ◽  
Local Loads ◽  
Electricity Bill ◽  
Net Metering ◽  
Cost Of Energy ◽  
Electrical Consumption

The latest measure for the development of photovoltaics in Greece utilizes the net-metering scheme. Under this scheme the energy produced by a PV system may be either consumed by the local loads or be injected to the grid. The final cost reported in an electricity bill depends upon the energy produced by the PV system, the energy absorbed from the grid and the energy injected to the grid. Consequently, the actual electricity consumption profile is important to estimate the benefit from the use of this renewable energy source. The state latest statistics in Greece for households reveal that the typical electrical consumption is 3750 kWh while 10244 kWh are consumed in the form of thermal energy. We adopt in our calculations the above amount of electrical energy but assume four different scenarios. These different hourly profiles are examined to study the effects of synchronization upon the final cost of energy. The above scenarios are applied to areas in different climate zones in Greece (Heraklion, Athens and Thessaloniki) to examine the dependence of the hourly profiles and the solar potential upon the financial data with respect to internal rate of return, payback times, net present value and the levelized cost of energy. These parameters are affected by the initial system cost and the financial parameters.

scholarly journals MPPT of PV System Under Partial Shading Conditions Based on Bio-inspired Swarm Intelligence Technique

2021 ◽  
Vol 297 ◽  
pp. 01051
Author(s):  
Mohammed Agdam ◽  
Abdallah Asbayou ◽  
Mustapha Elyaqouti ◽  
Ahmed Ihlal ◽  
Khaled Assalaou
Keyword(s):  
Swarm Intelligence ◽  
Electrical Energy ◽  
Pv System ◽  
Partial Shading ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Maximum Current ◽  
Maximum Voltage ◽  
Intelligence Technique

To respond to the increase in demand for electricity, the use of photovoltaics is growing considerably as it produces electrical energy without polluting the environment. In addition, to enhance the efficiency of photovoltaic modules, an MPPT algorithm is required to follow the maximum voltage and maximum current in the IV curve. This technique can be achieved by using a DC-DC converter. For this purpose, various MPPT techniques have been developed. The combination of MPPT and DC-DC converter is implemented using Matlab/Simulink and connected to a modelled PV module to validate the simulation.

scholarly journals Heat transfer study of poly-c PV system integrated with phase change material under semi-arid area (Errachidia-Drâa Tafilalet)

2021 ◽  
Vol 297 ◽  
pp. 01008
Author(s):  
Ibtissam Lamaamar ◽  
Amine Tilioua ◽  
Zaineb Benzaid ◽  
Abdelouahed Ait Msaad ◽  
Moulay Ahmed Hamdi Alaoui
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Phase Change Material ◽  
Operating Temperature ◽  
Pv System ◽  
Pv Module ◽  
Solidification Processes ◽  
Change Material ◽  
Transfer Study ◽  
Melting And Solidification

The high operating temperature of the photovoltaic (PV) modules decreases significantly its efficiency. The integration of phase change material (PCM) is one of the feasible techniques for reducing the operating temperature of the PV module. A numerical simulation of the PV module with PCM and without PCM has been realized. The thermal behavior of the PV module was evaluated at the melting and solidification processes of PCM. The results show that the integration of RT35HC PCM with a thickness of 4 cm reduces the temperature of the PV module by 8 °C compared to the reference module. Compared the RT35 and RT35HC, we found that the latent heat has a significant effect on the PCM thermal comportment. Furthermore, it has been found that the thermal resistance of the layers plays an important role to dissipate the heat from the PV cells to the PCM layer, consequently improving the heat transfer inside the PV/PCM system.

Sign in / Sign up

Export Citation Format

Share Document