Preparation and Characterization of Dysprosium (Dy) Ultrafine Nanocrystalline Structures

2008 ◽  
Vol 8 (2) ◽  
pp. 961-966
Author(s):  
Nianduan Lu ◽  
Xiaoyan Song ◽  
Jiuxing Zhang ◽  
Xiangquan Yan ◽  
Markus Rettenmayr
Keyword(s):  
Elastic Modulus ◽  
Nanocrystalline Structure ◽  
Physical And Mechanical Properties ◽  
Gas Condensation ◽  
Rhombohedral Crystal Structure ◽  
Nanocrystalline Structures ◽  
Metallic Nanomaterials ◽  
Efficient Route ◽  
Rhombohedral Crystal

By combining the inert-gas condensation with the SPS technology in an entirely closed system with the oxygen concentration below 0.5 ppm, the pure Dy bulk with the ultrafine nanocrystalline structure has been prepared. Thus a novel and efficient route of preparing nano rare-earth metals, as well as metallic nanomaterials that are highly reactive in the air, is proposed. The thermal, physical and mechanical properties of the prepared ultrafine nanocrystalline Dy bulk have been characterized and compared with those of the conventional raw polycrystalline bulk. It is found that in the nanocrystalline Dy bulk, the starting temperature of phase transformation from hexagonal to rhombohedral crystal structure is reduced by 70 °C in comparison with that of the raw polycrystalline bulk. The electrical resistivity of the ultrafine nanocrystalline bulk is slightly increased by a few percent as compared with that of the polycrystalline bulk, while the thermal conductivity is reduced by 28–35%. The microhardness and the elastic modulus of the ultrafine nanocrystalline Dy bulk are found to be remarkably improved as compared with those of the raw polycrystalline bulk, e.g., the microhardness and the elastic modulus are approximately 2.4 and 2.0 times as high as those of the raw polycrystalline bulk, respectively.

scholarly journals Structure and nanomechanical characterization of synthetic calcium-silicate-hydrate with poly-methacrylic acid

2020 ◽  
Vol 13 (5) ◽  
Author(s):  
Fernando Pelisser ◽  
Philippe Jean Paul Gleize ◽  
Alexandre Mikowski
Keyword(s):  
Elastic Modulus ◽  
Methacrylic Acid ◽  
Calcium Silicate ◽  
Calcium Silicate Hydrate ◽  
Construction Materials ◽  
Physical And Mechanical Properties ◽  
Polymer Complexes ◽  
Cement Pastes ◽  
Ft Ir

ABSTRACT: The principal phase of hardened Portland cement pastes is calcium silicate hydrate (C-S-H), which influences the physical and mechanical properties of construction materials. In this work, calcium silicate hydrate (C-S-H) was synthesized, with the addition of poly-methacrylic acid with sodium (PMA), for the development of C-S-H/ polymer nanocomposites. Among the polymers available, PMA is indicated in the literature as one of those viable for producing C-S-H/polymer complexes. However, no consensus exists regarding the type of interaction this produces. The resulting compounds were characterized by XRD, FT-IR, TGA, carbon content (CHN), TEM, SEM and elastic modulus and hardness were measured by instrumented indentation. A significant change was verified in the nanomechanical properties of C-S-H with PMA, resulting in reduction in the elastic modulus and hardness. The set of results presented do not confirm the intercalation of PMA in the interlayer space of C-S-H, but presented evidence of the potential for intercalation, since changes in the microstructure clearly occurred.

Interface structures in polycrystalline ceramic materials

1986 ◽  
Vol 44 ◽  
pp. 468-471
Author(s):  
K. J. Morrissey
Keyword(s):  
Electron Microscopy ◽  
Analytical Electron Microscopy ◽  
Physical And Mechanical Properties ◽  
High Resolution Electron Microscopy ◽  
Ceramic Materials ◽  
Polycrystalline Materials ◽  
Transmission Electron ◽  
Resolution Electron ◽  
Interface Structures

Grain boundaries and interfaces play an important role in determining both physical and mechanical properties of polycrystalline materials. To understand how the structure of interfaces can be controlled to optimize properties, it is necessary to understand and be able to predict their crystal chemistry. Transmission electron microscopy (TEM), analytical electron microscopy (AEM,), and high resolution electron microscopy (HREM) are essential tools for the characterization of the different types of interfaces which exist in ceramic systems. The purpose of this paper is to illustrate some specific areas in which understanding interface structure is important. Interfaces in sintered bodies, materials produced through phase transformation and electronic packaging are discussed.

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers

scholarly journals Characterization of Beeswax, Candelilla Wax and Paraffin Wax for Coating Cheeses

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 261
Author(s):  
Adolfo Bucio ◽  
Rosario Moreno-Tovar ◽  
Lauro Bucio ◽  
Jessica Espinosa-Dávila ◽  
Francisco Anguebes-Franceschi
Keyword(s):  
Physical And Mechanical Properties ◽  
Tensile Tests ◽  
Paraffin Wax ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Absorption Bands ◽  
Dimensional Changes ◽  
Ductile Behavior ◽  
Candelilla Wax

A study on the physical and mechanical properties of beeswax (BW), candelilla wax (CW), paraffin wax (PW) and blends was carried out with the aim to evaluate their usefulness as coatings for cheeses. Waxes were analyzed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), differential scanning calorimetry (DSC), permeability, viscosity, flexural and tensile tests and scanning electron microscopy. Cheeses were coated with the waxes and stored for 5 weeks at 30 °C. Measured parameters were weight, moisture, occurrence and degree of fractures, and dimensional changes. The crystal phases identified by XRD for the three waxes allowed them to determine the length of alkanes and the nonlinear compounds in crystallizable forms in waxes. FTIR spectra showed absorption bands between 1800 and 800 cm−1 related to carbonyls in BW and CW. In DSC, the onset of melting temperature was 45.5 °C for BW, and >54 °C for CW and PW. Cheeses coated with BW did not show cracks after storage. Cheeses coated with CW and PW showed microcraks, and lost weight, moisture and shrunk. In the flexural and tensile tests, BW was ductile; CW and PW were brittle. BW blends with CW or PW displays a semi ductile behavior. Cheeses coated with BW blends lost less than 5% weight during storage. The best waxes were BW and the blends.

scholarly journals A Universal Model for the Log-Normal Distribution of Elasticity in Polymeric Gels and Its Relevance to Mechanical Signature of Biological Tissues

Biology ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 64
Author(s):  
Arnaud Millet
Keyword(s):  
Elastic Modulus ◽  
Normal Distribution ◽  
Biological Tissues ◽  
Force Microscopy ◽  
Polymeric Gels ◽  
Atomic Force ◽  
Clear Explanation ◽  
Log Normal ◽  
Log Normal Distribution

The mechanosensitivity of cells has recently been identified as a process that could greatly influence a cell’s fate. To understand the interaction between cells and their surrounding extracellular matrix, the characterization of the mechanical properties of natural polymeric gels is needed. Atomic force microscopy (AFM) is one of the leading tools used to characterize mechanically biological tissues. It appears that the elasticity (elastic modulus) values obtained by AFM presents a log-normal distribution. Despite its ubiquity, the log-normal distribution concerning the elastic modulus of biological tissues does not have a clear explanation. In this paper, we propose a physical mechanism based on the weak universality of critical exponents in the percolation process leading to gelation. Following this, we discuss the relevance of this model for mechanical signatures of biological tissues.

scholarly journals Creation of Ionically Crosslinked Tri-Layered Chitosan Membranes to Simulate Different Human Skin Properties

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1807
Author(s):  
Rocío Guerle-Cavero ◽  
Blanca Lleal-Fontàs ◽  
Albert Balfagón-Costa
Keyword(s):  
Elastic Modulus ◽  
Human Skin ◽  
Sodium Tripolyphosphate ◽  
Snow Crab ◽  
Suitable Material ◽  
Cosmetic Industry ◽  
Novel Method ◽  
Current Article ◽  
Chitosan Membranes

In 2023, new legislation will ban the use of animals in the cosmetic industry worldwide. This fact, together with ethical considerations concerning the use of animals or humans in scientific research, highlights the need to propose new alternatives for replacing their use. The aim of this study is to create a tri-layered chitosan membrane ionically crosslinked with sodium tripolyphosphate (TPP) in order to simulate the number of layers in human skin. The current article highlights the creation of a membrane where pores were induced by a novel method. Swelling index, pore creation, and mechanical property measurements revealed that the swelling index of chitosan membranes decreased and, their pore formation and elasticity increased with an increase in the Deacetylation Grade (DDA). Additionally, the results demonstrate that chitosan’s origin can influence the elastic modulus value and reproducibility, with higher values being obtained with seashell than snow crab or shrimp shells. Furthermore, the data show that the addition of each layer, until reaching three layers, increases the elastic modulus. Moreover, if layers are crosslinked, the elastic modulus increases to a much greater extent. The characterization of three kinds of chitosan membranes was performed to find the most suitable material for studying different human skin properties.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Characterization of particleboard made from oil heat-treated rubberwood particles at different mixing ratios

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 6795-6810
Author(s):  
Nurul Fatiha Osman ◽  
Paimon Bawon ◽  
Seng Hua Lee ◽  
Pakhriazad Hassan Zaki ◽  
Syeed SaifulAzry Osman Al-Eldrus ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Oil Content ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Thermal Characterization ◽  
High Dimensional ◽  
Mixing Ratios ◽  
Uf Resin ◽  
Heat Treated

Particleboard was produced by mixing oil heat-treated rubberwood particles at different ratios, with the goal of achieving high dimensional stability. Rubberwood particles were soaked in palm oil for 2 h and heat treated at 200 °C for 2 h. The treated particles were soaked in boiling water for 30 min to remove oil and were tested for chemical alteration and thermal characterization via Fourier-transform infrared spectroscopy and thermogravimetric analysis. Particleboard was fabricated by mixing treated rubberwood particles (30%, 50%, and 70%) with untreated particles (70%, 50%, and 30%, respective to previous percentages) and bonded with urea-formaldehyde (UF) resin. The results revealed that oil-heat treated particles had greater thermal stability than the untreated particles. The addition of oil heat treated particles improved the physical properties of the particleboard with no significant reduction in mechanical strength. However, this was only valid for ratios of 70% untreated to 30% treated and 50% untreated to 50% treated. When a ratio of 70% oil heat treated particles was used, both the physical and mechanical properties were reduced drastically, due to bonding interference caused by excessive oil content. Particleboard made with a ratio of 5:5 (treated to untreated) exhibited the best physical and mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document