A Novel Amperometric Genosensor for Rapid Detection of Canine Parvovirus in Feces

2021 ◽  
Vol 21 (6) ◽  
pp. 3524-3530
Author(s):  
Rahul Khatri ◽  
Hari Mohan ◽  
Poonam ◽  
Basanti Brar ◽  
Minakshi Prasad ◽  
...  
Keyword(s):  
Vaccine Strain ◽  
Rapid Detection ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Canine Parvovirus ◽  
Current Response ◽  
Viral Dna ◽  
Electrochemical Impedance Spectra ◽  
Vp2 Gene ◽  
Au Electrode

A highly sensitive novel amperometric genosensor has been developed for rapid detection of canine parvovirus (CPV) DNA in fecal swabs of naturally infected dogs. The genosensor is based on a single stranded 5°-thiolated (SH) DNA probe complementary to VP1/VP2 gene of canine parvo vaccine strain, immobilized covalently on a polycrystalline gold (Au) electrode. The genosensor has been characterized by scanning electron microscopy (SEM), Fourier Transform Infra-Red Spectroscopy (FTIR), cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectra (EIS). The ssDNA-SH/Au electrode was hybridized with single stranded target DNA (ss T-DNA) in the sample. This hybridization was detected by reduction in current, generated by interaction of methylene blue (MB) with free guanine of ssDNA. The current response of genosensor was determined by CV, DPV and EIS. The sensor detected single stranded genomic DNA (ss g-DNA) isolated from vaccine strain of CPV in the range, 1.0–12.0 ng/μl at 25 °C for 10 min. Subsequently, the genobiosensor was applied for detection of CPV viral DNA in fecal swabs of naturally infected dogs. The limit of detection (LOD) of the sensor was 1.0 ng/μl of fecal viral DNA. To the best of our knowledge, this is the first report on development and application of amperometric biosensor for rapid, sensitive, specific point of care detection of viral DNA of CPV in feces.

scholarly journals Label-Free Electrochemical Detection of S. mutans Exploiting Commercially Fabricated Printed Circuit Board Sensing Electrodes

Micromachines ◽  
2019 ◽  
Vol 10 (9) ◽  
pp. 575 ◽  
Author(s):  
Gorachand Dutta ◽  
Abdoulie A. Jallow ◽  
Debjani Paul ◽  
Despina Moschou
Keyword(s):  
Electrochemical Detection ◽  
Printed Circuit Board ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Charge Transfer Resistance ◽  
Circuit Board ◽  
Label Free ◽  
Electrochemical Impedance Spectra ◽  
Transfer Resistance ◽  
Printed Circuit

This paper reports for the first time printed-circuit-board (PCB)-based label-free electrochemical detection of bacteria. The demonstrated immunosensor was implemented on a PCB sensing platform which was designed and fabricated in a standard PCB manufacturing facility. Bacteria were directly captured on the PCB sensing surface using a specific, pre-immobilized antibody. Electrochemical impedance spectra (EIS) were recorded and used to extract the charge transfer resistance (Rct) value for the different bacteria concentrations under investigation. As a proof-of-concept, Streptococcus mutans (S. mutans) bacteria were quantified in a phosphate buffered saline (PBS) buffer, achieving a limit of detection of 103 CFU/mL. Therefore, the proposed biosensor is an attractive candidate for the development of a simple and robust point-of-care diagnostic platform for bacteria identification, exhibiting good sensitivity, high selectivity, and excellent reproducibility.

scholarly journals Screen Printed Based Impedimetric Immunosensor for Rapid Detection of Escherichia coli in Drinking Water

Sensors ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 274 ◽  
Author(s):  
Martina Cimafonte ◽  
Andrea Fulgione ◽  
Rosa Gaglione ◽  
Marina Papaianni ◽  
Rosanna Capparelli ◽  
...  
Keyword(s):  
Escherichia Coli ◽  
Drinking Water ◽  
Rapid Detection ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Phosphate Buffer Solution ◽  
Relevant Parameter ◽  
Transfer Resistance ◽  
E Coli ◽  
Screen Printed

The development of a simple and low cost electrochemical impedance immunosensor based on screen printed gold electrode for rapid detection of Escherichia coli in water is reported. The immunosensor is fabricated by immobilizing anti-E. coli antibodies onto a gold surface in a covalent way by the photochemical immobilization technique, a simple procedure able to bind antibodies upright onto gold surfaces. Impedance spectra are recorded in 0.01 M phosphate buffer solution (PBS) containing 10 mM Fe(CN)63−/Fe(CN)64− as redox probe. The Nyquist plots can be modelled with a modified Randles circuit, identifying the charge transfer resistance Rct as the relevant parameter after the immobilization of antibodies, the blocking with BSA and the binding of E. coli. The introduction of a standard amplification procedure leads to a significant enhancement of the impedance increase, which allows one to measure E. coli in drinking water with a limit of detection of 3 × 101 CFU mL−1 while preserving the rapidity of the method that requires only 1 h to provide a “yes/no” response. Additionally, by applying the Langmuir adsorption model, we are able to describe the change of Rct in terms of the “effective” electrode, which is modified by the detection of the analyte whose microscopic conducting properties can be quantified.

scholarly journals Electrochemical Determination of Lead & Copper Ions Using Thiolated Calix[4]arene-Modified Screen-Printed Carbon Electrode

Chemosensors ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 157
Author(s):  
Chong Jin Mei ◽  
Nor Azah Yusof ◽  
Shahrul Ainliah Alang Ahmad
Keyword(s):  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Copper Ions ◽  
Current Response ◽  
Carbon Electrode ◽  
Significant Drop ◽  
Screen Printed Carbon Electrode ◽  
Relative Standard ◽  
Competitive Ions ◽  
Screen Printed

This study used a thiolated calix[4]arene derivative modified on gold nanoparticles and a screen-printed carbon electrode (TC4/AuNPs/SPCE) for Pb2+ and Cu2+ determination. The surface of the modified electrode was characterised via Fourier-transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Differential pulse voltammetry (DPV) was used for the detection of Pb2+ and Cu2+ under optimum conditions. The limit of detection (LOD) for detecting Pb2+ and Cu2+ was 0.7982 × 10−2 ppm and 1.3358 × 10−2 ppm, respectively. Except for Zn2+ and Hg2+, the presence of competitive ions caused little effect on the current response when detecting Pb2+. However, all competitive ions caused a significant drop in the current response when detecting Cu2+, except Ca2+ and Mg2+, suggesting the sensing platform is more selective toward Pb2+ ions rather than copper (Cu2+) ions. The electrochemical sensor demonstrated good reproducibility and excellent stability with a low relative standard deviation (RSD) value in detecting lead and copper ions. Most importantly, the result obtained in the analysis of Pb2+ and Cu2+ had good recovery in river water, demonstrating the applicability of the developed sensor for real samples.

The study of the electrochemical properties of zinc-rich coating on the base of water sodium silicate

2019 ◽  
Vol 24 (4) ◽  
pp. 51-58
Author(s):  
Le Hong Quan ◽  
Nguyen Van Chi ◽  
Mai Van Minh ◽  
Nong Quoc Quang ◽  
Dong Van Kien
Keyword(s):  
Carbon Steel ◽  
Electrochemical Properties ◽  
Sodium Silicate ◽  
Cathodic Protection ◽  
Electrochemical Impedance ◽  
Steel Substrate ◽  
Electrical Contact ◽  
Electrochemical Impedance Spectra ◽  
Pure Zinc ◽  
Electric Circuits

The study examines the electrochemical properties of a coating based on water sodium silicate and pure zinc dust (ZSC, working title - TTL-VN) using the Electrochemical Impedance Spectra (EIS) with AutoLAB PGSTAT204N. The system consists of three electrodes: Ag/AgCl (SCE) reference electrode in 3 M solution of KCl, auxiliary electrode Pt (8x8 mm) and working electrodes (carbon steel with surface treatment up to Sa 2.5) for determination of corrosion potential (Ecorr) and calculation of equivalent electric circuits used for explanation of impedance measurement results. It was shown that electrochemical method is effective for study of corrosion characteristics of ZSC on steel. We proposed an interpretation of the deterioration over time of the ability of zinc particles in paint to provide cathodic protection for carbon steel. The results show that the value of Ecorr is between -0,9 and -1,1 V / SCE for ten days of diving. This means that there is an electrical contact between the zinc particles, which provides good cathodic protection for the steel substrate and most of the zinc particles were involved in the osmosis process. The good characteristics of the TTL-VN coating during immersion in a 3,5% NaCl solution can also be explained by the preservation of corrosive zinc products in the coating, which allows the creation of random barrier properties.

scholarly journals Antireflection Improvement and Junction Quality Optimization of Si/PEDOT:PSS Solar Cell with the Introduction of Dopamine@Graphene

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5986
Author(s):  
Tao Chen ◽  
Hao Guo ◽  
Leiming Yu ◽  
Tao Sun ◽  
Anran Chen ◽  
...  
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
High Performance ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrochemical Impedance Spectra ◽  
Solar Cell Performance ◽  
Photovoltaic Conversion ◽  
Photovoltaic Conversion Efficiency

Si/PEDOT: PSS solar cell is an optional photovoltaic device owing to its promising high photovoltaic conversion efficiency (PCE) and economic manufacture process. In this work, dopamine@graphene was firstly introduced between the silicon substrate and PEDOT:PSS film for Si/PEDOT: PSS solar cell. The dopamine@graphene was proved to be effective in improving the PCE, and the influence of mechanical properties of dopamine@graphene on solar cell performance was revealed. When dopamine@graphene was incorporated into the cell preparation, the antireflection ability of the cell was enhanced within the wavelength range of 300~450 and 650~1100 nm. The enhanced antireflection ability would benefit amount of the photon-generated carriers. The electrochemical impedance spectra test revealed that the introduction of dopamine@graphene could facilitate the separation of carriers and improve the junction quality. Thus, the short-circuit current density and fill factor were both promoted, which led to the improved PCE. Meanwhile, the influence of graphene concentration on device performances was also investigated. The photovoltaic conversion efficiency would be promoted from 11.06% to 13.15% when dopamine@graphene solution with concentration 1.5 mg/mL was applied. The achievements of this study showed that the dopamine@graphene composites could be an useful materials for high-performance Si/PEDOT:PSS solar cells.

Performance of Ba0.5Sr0.5Co0.8Fe0.2O3-δ-Ag Composite Cathode Materials for IT-SOFCs

2011 ◽  
Vol 311-313 ◽  
pp. 2309-2314 ◽  
Author(s):  
Wen Xia Zhu ◽  
Zhe Lü ◽  
Le Xin Wang ◽  
Xiao Yan Guan ◽  
Xin Yan Zhang
Keyword(s):  
Solid Oxide Fuel Cells ◽  
Electrochemical Impedance ◽  
Composite Cathode ◽  
Solid Oxide ◽  
Electrode Polarization ◽  
Impedance Spectra ◽  
Electrochemical Impedance Spectra ◽  
Composite Cathodes ◽  
Reduced Temperature ◽  
Resistance Value

°Abstract. In order to develop new cathodes for reduced temperature SOFCs, Ba0.5Sr0.5Co0.8Fe0.2O3-δ-Ag composite cathode was investigated in intermediate-temperature Solid Oxide Fuel Cells (IT-SOFCs). The XRD results suggested that no chemical reactions between BSCF and Ag in the composite cathode were found. The resistance measurements showed that the addition of Ag into BSCF improved electrical conductivity of pure BSCF, and the improved conductivity resulted in attractive cathode performance. In addition, electrochemical impedance spectra exhibited the better performance of BSCF-Ag composite cathodes than pure BSCF, e.g., the polarization resistance value of BSCF-Ag was only 0.36Ω cm2 at 650°C, which was nearly 80% lower than that of BSCF electrode. Polarization curves showed the overpotential decreased with the addition of Ag. The current density value of BSCF-Ag was 0.88Acm-2 under –120mV, about five times of that BSCF measured at 650°C. As a summary, compared to a pure BSCF cathode, it was found that adding Ag in the cathode enhanced the BSCF performance significantly.

scholarly journals Cerebellar hypoplasia and dysplasia in a juvenile raccoon with parvoviral infection

2020 ◽  
Vol 32 (3) ◽  
pp. 463-466 ◽  
Author(s):  
Arno Wünschmann ◽  
Robert Lopez-Astacio ◽  
Anibal G. Armien ◽  
Colin R. Parrish
Keyword(s):  
Granule Cells ◽  
Nonstructural Protein ◽  
Canine Parvovirus ◽  
Cerebellar Hypoplasia ◽  
Diagnostic Laboratory ◽  
Vp2 Gene ◽  
Nonstructural Protein 1 ◽  
Cell Processes ◽  
Ns1 Gene ◽  
Pcr Targeting

A juvenile raccoon ( Procyon lotor) was submitted dead to the Minnesota Veterinary Diagnostic Laboratory for rabies testing without history. The animal had marked hypoplasia of the cerebellum. Histology demonstrated that most folia lacked granule cells and had randomly misplaced Purkinje cells. Immunohistochemistry revealed the presence of parvoviral antigen in a few neurons and cell processes. PCR targeting feline and canine parvovirus yielded a positive signal. Sequencing analyses from a fragment of the nonstructural protein 1 ( NS1) gene and a portion of the viral capsid protein 2 ( VP2) gene confirmed the presence of DNA of a recent canine parvovirus variant (CPV-2a–like virus) in the cerebellum. Our study provides evidence that (canine) parvovirus may be associated with cerebellar hypoplasia and dysplasia in raccoons, similar to the disease that occurs naturally and has been reproduced experimentally by feline parvoviral infection of pregnant cats, with subsequent intrauterine or neonatal infections of the offspring.

scholarly journals Electrochemical Immunosensor for the Quantification of S100B at Clinically Relevant Levels Using a Cysteamine Modified Surface

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 1929
Author(s):  
Alexander Rodríguez ◽  
Francisco Burgos-Flórez ◽  
José D. Posada ◽  
Eliana Cervera ◽  
Valtencir Zucolotto ◽  
...  
Keyword(s):  
Frequency Analysis ◽  
Surface Characterization ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Neuronal Damage ◽  
Charge Transfer Resistance ◽  
Single Frequency ◽  
Response Analysis ◽  
Transfer Resistance ◽  
Therapeutic Decisions

Neuronal damage secondary to traumatic brain injury (TBI) is a rapidly evolving condition, which requires therapeutic decisions based on the timely identification of clinical deterioration. Changes in S100B biomarker levels are associated with TBI severity and patient outcome. The S100B quantification is often difficult since standard immunoassays are time-consuming, costly, and require extensive expertise. A zero-length cross-linking approach on a cysteamine self-assembled monolayer (SAM) was performed to immobilize anti-S100B monoclonal antibodies onto both planar (AuEs) and interdigitated (AuIDEs) gold electrodes via carbonyl-bond. Surface characterization was performed by atomic force microscopy (AFM) and specular-reflectance FTIR for each functionalization step. Biosensor response was studied using the change in charge-transfer resistance (Rct) from electrochemical impedance spectroscopy (EIS) in potassium ferrocyanide, with [S100B] ranging 10–1000 pg/mL. A single-frequency analysis for capacitances was also performed in AuIDEs. Full factorial designs were applied to assess biosensor sensitivity, specificity, and limit-of-detection (LOD). Higher Rct values were found with increased S100B concentration in both platforms. LODs were 18 pg/mL(AuES) and 6 pg/mL(AuIDEs). AuIDEs provide a simpler manufacturing protocol, with reduced fabrication time and possibly costs, simpler electrochemical response analysis, and could be used for single-frequency analysis for monitoring capacitance changes related to S100B levels.

scholarly journals Electrochemical Detection of Endosulfan Using an AONP-PANI-SWCNT Modified Glassy Carbon Electrode

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 723
Author(s):  
Kgotla K. Masibi ◽  
Omolola E. Fayemi ◽  
Abolanle S. Adekunle ◽  
Amal M. Al-Mohaimeed ◽  
Asmaa M. Fahim ◽  
...  
Keyword(s):  
Glassy Carbon Electrode ◽  
Glassy Carbon ◽  
Limit Of Detection ◽  
Modified Electrodes ◽  
Antimony Oxide ◽  
Current Response ◽  
Carbon Electrode ◽  
Trace Detection ◽  
Limit Of Quantification ◽  
Walled Carbon Nanotubes

This report narrates the successful application of a fabricated novel sensor for the trace detection of endosulfan (EDS). The sensor was made by modifying a glassy-carbon electrode (GCE) with polyaniline (PANI), chemically synthesized antimony oxide nanoparticles (AONPs), acid-functionalized, single-walled carbon nanotubes (fSWCNTs), and finally, the AONP-PANI-SWCNT nanocomposite. The electrochemical properties of the modified electrodes regarding endosulfan detection were investigated via cyclic voltammetry (CV) and square-wave voltammetry. The current response of the electrodes to EDS followed the trend GCE-AONP-PANI-SWCNT (−510 µA) > GCE-PANI (−59 µA) > GCE-AONPs (−11.4 µA) > GCE (−5.52 µA) > GCE-fSWCNTs (−0.168 µA). The obtained results indicated that the current response obtained at the AONP-PANI-SWCNT/GCE was higher with relatively low overpotential compared to those from the other electrodes investigated. This demonstrated the superiority of the AONP-PANI-SWCNT-modified GCE. The AONP-PANI-SWCNT/GCE demonstrated good electrocatalytic activities for the electrochemical reduction of EDS. The results obtained in this study are comparable with those in other reports. The sensitivity, limit of detection (LoD), and limit of quantification (LoQ) of AONP-PANI-SWCNT/GCE towards EDS was estimated to be 0.0623 µA/µM, 6.8 µM, and 20.6 µM, respectively. Selectivity, as well as the practical application of the fabricated sensor, were explored, and the results indicated that the EDS-reduction current was reduced by only 2.0% when interfering species were present, whilst average recoveries of EDS in real samples were above 97%.

scholarly journals MnO2@Reduced Graphene Oxide Nanocomposite-Based Electrochemical Sensor for the Simultaneous Determination of Trace Cd(II), Zn(II) and Cu(II) in Water Samples

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 517
Author(s):  
Siyamthanda Hope Mnyipika ◽  
Tshimangadzo Saddam Munonde ◽  
Philiswa Nosizo Nomngongo
Keyword(s):  
Heavy Metals ◽  
Electrochemical Sensor ◽  
Simultaneous Determination ◽  
Rapid Detection ◽  
Electrochemical Sensors ◽  
Simultaneous Detection ◽  
Cyclic Voltammograms ◽  
Current Response ◽  
Mno2 Nanoparticles

The rapid detection of trace metals is one of the most important aspect in achieving environmental monitoring and protection. Electrochemical sensors remain a key solution for rapid detection of heavy metals in environmental water matrices. This paper reports the fabrication of an electrochemical sensor obtained by the simultaneous electrodeposition of MnO2 nanoparticles and RGO nanosheets on the surface of a glassy carbon electrode. The successful electrodeposition was confirmed by the enhanced current response on the cyclic voltammograms. The XRD, HR-SEM/EDX, TEM, FTIR, and BET characterization confirmed the successful synthesis of MnO2 nanoparticles, RGO nanosheets, and MnO2@RGO nanocomposite. The electrochemical studies results revealed that MnO2@RGO@GCE nanocomposite considerably improved the current response on the detection of Zn(II), Cd(II) and Cu(II) ions in surface water. These remarkable improvements were due to the interaction between MnO2 nanomaterials and RGO nanosheets. Moreover, the modified sensor electrode portrayed high sensitivity, reproducibility, and stability on the simultaneous determination of Zn(II), Cd(II), and Cu(II) ions. The detection limits of (S/N = 3) ranged from 0.002–0.015 μg L−1 for the simultaneous detection of Zn(II), Cd(II), and Cu(II) ions. The results show that MnO2@RGO nanocomposite can be successfully used for the early detection of heavy metals with higher sensitivity in water sample analysis.

Sign in / Sign up

Export Citation Format

Share Document