scholarly journals Direct Calculation of Thermodynamic Wet-Bulb Temperature as a Function of Pressure and Elevation

2013 ◽  
Vol 30 (8) ◽  
pp. 1757-1765 ◽  
Author(s):  
Sayed-Hossein Sadeghi ◽  
Troy R. Peters ◽  
Douglas R. Cobos ◽  
Henry W. Loescher ◽  
Colin S. Campbell
Keyword(s):  
Air Temperature ◽  
Mean Absolute Error ◽  
Direct Calculation ◽  
Ambient Air ◽  
Absolute Error ◽  
Mean Square ◽  
Air Temperatures ◽  
Order Polynomial ◽  
The Mean ◽  
Very High

Abstract A simple analytical method was developed for directly calculating the thermodynamic wet-bulb temperature from air temperature and the vapor pressure (or relative humidity) at elevations up to 4500 m above MSL was developed. This methodology was based on the fact that the wet-bulb temperature can be closely approximated by a second-order polynomial in both the positive and negative ranges in ambient air temperature. The method in this study builds upon this understanding and provides results for the negative range of air temperatures (−17° to 0°C), so that the maximum observed error in this area is equal to or smaller than −0.17°C. For temperatures ≥0°C, wet-bulb temperature accuracy was ±0.65°C, and larger errors corresponded to very high temperatures (Ta ≥ 39°C) and/or very high or low relative humidities (5% < RH < 10% or RH > 98%). The mean absolute error and the root-mean-square error were 0.15° and 0.2°C, respectively.

Explanation Plus Prediction—The Logical Focus of Project Management Research

2021 ◽  
pp. 875697282199994
Author(s):  
Joseph F. Hair ◽  
Marko Sarstedt
Keyword(s):  
Project Management ◽  
Statistical Models ◽  
Predictive Power ◽  
Mean Absolute Error ◽  
Explanatory Power ◽  
Absolute Error ◽  
Model Parameters ◽  
Mean Square ◽  
Management Research ◽  
The Mean

Most project management research focuses almost exclusively on explanatory analyses. Evaluation of the explanatory power of statistical models is generally based on F-type statistics and the R 2 metric, followed by an assessment of the model parameters (e.g., beta coefficients) in terms of their significance, size, and direction. However, these measures are not indicative of a model’s predictive power, which is central for deriving managerial recommendations. We recommend that project management researchers routinely use additional metrics, such as the mean absolute error or the root mean square error, to accurately quantify their statistical models’ predictive power.

Accuracy Assessment of TanDEM-X 90 and CartoDEM Using ICESat-2 Datasets for Plain Regions of Ratlam City and Surroundings

2021 ◽  
Vol 10 (1) ◽  
pp. 59
Author(s):  
Unnati Yadav ◽  
Ashutosh Bhardwaj
Keyword(s):  
Mean Absolute Error ◽  
Accuracy Assessment ◽  
Absolute Error ◽  
Terrain Analysis ◽  
Mean Square ◽  
High Quality ◽  
Ice Cloud ◽  
The Mean ◽  
Cut And Fill ◽  
Statistical Results

The spaceborne LiDAR dataset from the Ice, Cloud, and Land Elevation Satellite (ICESat-2) provides highly accurate measurements of heights for the Earth’s surface, which helps in terrain analysis, visualization, and decision making for many applications. TanDEM-X 90 (90 m) and CartoDEM V3R1 (30 m) elevation are among the high-quality openly accessible DEM datasets for the plain regions in India. These two DEMs are validated against the ICESat-2 elevation datasets for the relatively plain areas of Ratlam City and its surroundings. The mean error (ME), mean absolute error (MAE), and root mean square error (RMSE) of TanDEM-X 90 DEM are 1.35 m, 1.48 m, and 2.19 m, respectively. The computed ME, MAE, and RMSE for CartoDEM V3R1 are 3.05 m, 3.18 m, and 3.82 m, respectively. The statistical results reveal that TanDEM-X 90 performs better in plain areas than CartoDEMV3R1. The study further indicates that these DEMs and spaceborne LiDAR datasets can be useful for planning various works requiring height as an important parameter, such as the layout of pipelines or cut and fill calculations for various construction activities. The TanDEM-X 90 can assist planners in quick assessments of the terrain for infrastructural developments, which otherwise need time-consuming traditional surveys using theodolite or a total station.

scholarly journals Wet-Bulb Temperature from Relative Humidity and Air Temperature

2011 ◽  
Vol 50 (11) ◽  
pp. 2267-2269 ◽  
Author(s):  
Roland Stull
Keyword(s):  
Gene Expression ◽  
Relative Humidity ◽  
Sea Level ◽  
Air Temperature ◽  
Mean Absolute Error ◽  
Gene Expression Programming ◽  
Absolute Error ◽  
Sea Level Pressure ◽  
Air Temperatures ◽  
Low Humidity

AbstractAn equation is presented for wet-bulb temperature as a function of air temperature and relative humidity at standard sea level pressure. It was found as an empirical fit using gene-expression programming. This equation is valid for relative humidities between 5% and 99% and for air temperatures between −20° and 50°C, except for situations having both low humidity and cold temperature. Over the valid range, errors in wet-bulb temperature range from −1° to +0.65°C, with mean absolute error of less than 0.3°C.

scholarly journals Statistical Models in Estimating Air Temperature in a Mountainous Region of Greece

2017 ◽  
Vol 12 (3) ◽  
pp. 544-549 ◽  
Author(s):  
Stelios Maniatis ◽  
Kostas Chronopoulos ◽  
Aristidis Matsoukis ◽  
Athanasios Kamoutsis
Keyword(s):  
Air Temperature ◽  
Statistical Models ◽  
Mean Absolute Error ◽  
Absolute Error ◽  
Coefficient Of Determination ◽  
Multi Layer Perceptron ◽  
Simple Linear Regression ◽  
The Mean ◽  
Of Greece ◽  
Better Than

The current work focuses on the estimation of air temperature (T) conditions in two high altitude (alt) sites (1580 m), each one at different orientation (southeast and northwest) in the mountain (Mt) Aenos in the island of Cephalonia, Greece, by using two well-known statistical models, simple linear regression (SLR) and multi-layer perceptron ( MLP), one of the most commonly used artificial neural networks. More specifically, the estimation of mean, maximum and minimum T in high alt sites was based on the respective T data of two lower alt sites (1100 m), the first at southeast and the second at northwest orientations, and was carried out separately for each orientation. The performance of both SLR and MLP models was evaluated by the coefficient of determination (R2) and the Mean Absolute Error (MAE). Results showed that the examined models (SLR and MLP) provided very satisfactory results with regard to the estimation of mean, maximum and minimum T, regarding southeast orientation (R2 ranging from 0.96 to 0.98), with mean T estimation being relatively better, as confirmed by the lowest MAE (0.83). Regarding northwest orientation, T estimation was less accurate (lower R2 and higher MAE), compared to the respective estimation of southeast orientation, but, the results were considered adequate (R2 and MAE ranging from 0.88 to 0.92 and 1.00 to 1.40, respectively). In general, the estimations of the mean T were better than those of the extreme ones (minimum and maximum T). In addition, better results (higher R2 and lower, in general, MAE) were obtained when T estimations were based on T data derived from sites located at areas with similar surroundings, as in the case of dense and tall vegetation of the sites at southeast orientation, irrespective of applied method.

scholarly journals Validation of the procedure: Quantification of the degradation index of Photovoltaic Grid Connection Systems

2021 ◽  
Vol 2 (5) ◽  
pp. 8-13
Author(s):  
Proenza Y. Roger ◽  
Camejo C. José Emilio ◽  
Ramos H. Rubén
Keyword(s):  
Mean Absolute Error ◽  
Absolute Error ◽  
Coefficient Of Determination ◽  
Mean Square ◽  
Degradation Index ◽  
Statistical Parameters ◽  
Grid Connection ◽  
The Mean

The results obtained from the validation of the procedure ‟Quantification of the degradation index of Photovoltaic Grid Connection Systems” are presented, using statistical parameters, which corroborate its accuracy, achieving a coefficient of determination of 0.9896, a percentage of the root of the mean square of the error RMSPE = 1.498% and a percentage of the mean absolute error MAPE = 1.15%, evidencing the precision of the procedure.

scholarly journals Comparison of different approaches to estimate bark volume of industrial wood at disc and log scale

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ferréol Berendt ◽  
Felipe de Miguel-Diez ◽  
Evelyn Wallor ◽  
Lubomir Blasko ◽  
Tobias Cremer
Keyword(s):  
Mean Absolute Error ◽  
Absolute Error ◽  
Solid Wood ◽  
Volume Estimation ◽  
Coefficient Of Determination ◽  
Mean Square ◽  
Bark Thickness ◽  
Wood Industry ◽  
The Mean ◽  
Wood Content

AbstractWithin the wood supply chain, the measurement of roundwood plays a key role due to its high economic impact. While wood industry mainly processes the solid wood, the bark mostly remains as an industrial by-product. In Central Europe, it is common that the wood is sold over bark but that the price is calculated on a timber volume under bark. However, logs are often measured as stacks and, thus, the volume includes not only the solid wood content but also the bark portion. Mostly, the deduction factors used to estimate the solid wood content are based on bark thickness. The aim of this study was to compare the estimation of bark volume from scaling formulae with the real bark volume, obtained by xylometric technique. Moreover, the measurements were performed using logs under practice conditions and using discs under laboratory conditions. The mean bark volume was 6.9 dm3 and 26.4 cm3 for the Norway spruce logs and the Scots pine discs respectively. Whereas the results showed good performances regarding the root mean square error, the coefficient of determination (R2) and the mean absolute error for the volume estimation of the total volume of discs and logs (over bark), the performances were much lower for the bark volume estimations only.

scholarly journals Saturated Pseudoadiabats—A Noniterative Approximation

2013 ◽  
Vol 52 (1) ◽  
pp. 5-15 ◽  
Author(s):  
Atoossa Bakhshaii ◽  
Roland Stull
Keyword(s):  
Air Temperature ◽  
Mean Absolute Error ◽  
Gene Expression Programming ◽  
Potential Temperature ◽  
Absolute Error ◽  
Final Temperature ◽  
New Variant ◽  
The Mean ◽  
Thermodynamic Domain ◽  
Lifting Condensation Level

AbstractTwo noniterative approximations are presented for saturated pseudoadiabats (also known as moist adiabats). One approximation determines which moist adiabat passes through a point of known pressure and temperature, such as through the lifting condensation level on a skew T or tephigram. The other approximation determines the air temperature at any pressure along a known moist adiabat, such as the final temperature of a rising cloudy air parcel. The method used to create these statistical regressions is a relatively new variant of genetic programming called gene-expression programming. The correlation coefficient between the resulting noniterative approximations and the iterated data such as plotted on thermodynamic diagrams is over 99.97%. The mean absolute error is 0.28°C, and the root mean square error is 0.44 within a thermodynamic domain bounded by −30° < θw ≤ 40°C, P > 20 kPa, and −60° ≤ T ≤ 40°C, where θw, P, and T are wet-bulb potential temperature, pressure, and air temperature.

scholarly journals An Algorithm for Density Enrichment of Sparse Collaborative Filtering Datasets Using Robust Predictions as Derived Ratings

Algorithms ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 174
Author(s):  
Dionisis Margaris ◽  
Dimitris Spiliotopoulos ◽  
Gregory Karagiorgos ◽  
Costas Vassilakis
Keyword(s):  
Collaborative Filtering ◽  
Mean Absolute Error ◽  
Pearson Correlation ◽  
Absolute Error ◽  
Mean Square ◽  
Error Metrics ◽  
Target User ◽  
The Mean ◽  
Rating Prediction ◽  
Sparsity Problem

Collaborative filtering algorithms formulate personalized recommendations for a user, first by analysing already entered ratings to identify other users with similar tastes to the user (termed as near neighbours), and then using the opinions of the near neighbours to predict which items the target user would like. However, in sparse datasets, too few near neighbours can be identified, resulting in low accuracy predictions and even a total inability to formulate personalized predictions. This paper addresses the sparsity problem by presenting an algorithm that uses robust predictions, that is predictions deemed as highly probable to be accurate, as derived ratings. Thus, the density of sparse datasets increases, and improved rating prediction coverage and accuracy are achieved. The proposed algorithm, termed as CFDR, is extensively evaluated using (1) seven widely-used collaborative filtering datasets, (2) the two most widely-used correlation metrics in collaborative filtering research, namely the Pearson correlation coefficient and the cosine similarity, and (3) the two most widely-used error metrics in collaborative filtering, namely the mean absolute error and the root mean square error. The evaluation results show that, by successfully increasing the density of the datasets, the capacity of collaborative filtering systems to formulate personalized and accurate recommendations is considerably improved.

Sign in / Sign up

Export Citation Format

Share Document