Fabrication and experimental evaluation of vibration and damping in multiscale graphene/fiberglass/epoxy composites

2019 ◽  
Vol 53 (15) ◽  
pp. 2105-2118 ◽  
Author(s):  
M Rafiee ◽  
F Nitzsche ◽  
MR Labrosse
Keyword(s):  
Graphene Oxide ◽  
Natural Frequencies ◽  
Damping Ratio ◽  
Epoxy Composites ◽  
Structural Vibration ◽  
Damping Properties ◽  
Multiwalled Carbon ◽  
Glass Fiber Reinforced ◽  
Vibration Technique ◽  
Wide Range

In this paper, the vibration and damping properties of multiscale laminated fiberglass/epoxy composites modified with a wide range of carbon nanofillers, including multiwalled carbon nanotubes, graphene oxide, reduced-graphene oxide and graphene nanoplatelets were examined for use in structural vibration applications. Simultaneous reinforcement of matrix and fibers was carried out via a novel method that combines a nanoparticle spraying process with nanoparticle/epoxy mixture to incorporate nanoparticles for the enhancement of vibration and damping properties of multiscale laminated fiberglass/epoxy composites. The vibration and damping properties as well as morphological, mechanical properties of the glass fiber-reinforced multiscale composites were investigated. Using a forced vibration technique, the frequency-response functions, natural frequencies and damping ratios of the nanocomposites were measured. The experimental results revealed that the damped natural frequencies of the nanocomposites increased with an increase in nanoparticle concentration. However, at higher contents of nanoparticles, the damped natural frequencies decreased and the damping ratio increased.

Determination of Strength and Damping Characteristics of Carbon Nanotube-Epoxy Composites

2004 ◽  
Author(s):  
Himanshu Rajoria ◽  
Nader Jalili
Keyword(s):  
Carbon Nanotube ◽  
Impulse Response ◽  
Composite Beam ◽  
Damping Ratio ◽  
Chemical Vapor ◽  
Deposition Process ◽  
Epoxy Composites ◽  
Damping Properties ◽  
Stick Slip ◽  
Pzt Actuator

In this paper, the strength and damping properties of carbon nanotube-epoxy composites are examined. Carbon nanotubes (Single-walled and Multi-walled) were grown on stainless steel substrates using thermal chemical vapor deposition process. The nanotube-epoxy composites were then prepared by applying a layer of epoxy on the grown nanotubes and a PZT actuator was attached on this layer. The composite beam consisting of steel, nanotube-epoxy layer and PZT actuator was used as a cantilever beam for vibration experiments in order to determine the enhancement in strength and damping properties of the nanotube-epoxy layer. Several different samples were prepared for this purpose. Impulse and frequency sweep tests were conducted on these beams to obtain the impulse response and frequency response functions. Fast Fourier Transform of the impulse response was used to find the natural frequency of the composite beam. It was observed that there was an increase in the stiffness by using multi-walled nanotubes in the epoxy, while the damping ratio increased by using single-walled nanotubes. The stick-slip mechanism is discussed in order to explain the results obtained.

scholarly journals Spatially Resolved Experimental Modal Analysis on High-Speed Composite Rotors Using a Non-Contact, Non-Rotating Sensor

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4705
Author(s):  
Julian Lich ◽  
Tino Wollmann ◽  
Angelos Filippatos ◽  
Maik Gude ◽  
Juergen Czarske ◽  
...  
Keyword(s):  
High Speed ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Fiber Reinforced ◽  
Structural Dynamic ◽  
Spatially Resolved ◽  
Glass Fiber Reinforced ◽  
Vibration Responses ◽  
And Performance

Due to their lightweight properties, fiber-reinforced composites are well suited for large and fast rotating structures, such as fan blades in turbomachines. To investigate rotor safety and performance, in situ measurements of the structural dynamic behaviour must be performed during rotating conditions. An approach to measuring spatially resolved vibration responses of a rotating structure with a non-contact, non-rotating sensor is investigated here. The resulting spectra can be assigned to specific locations on the structure and have similar properties to the spectra measured with co-rotating sensors, such as strain gauges. The sampling frequency is increased by performing consecutive measurements with a constant excitation function and varying time delays. The method allows for a paradigm shift to unambiguous identification of natural frequencies and mode shapes with arbitrary rotor shapes and excitation functions without the need for co-rotating sensors. Deflection measurements on a glass fiber-reinforced polymer disk were performed with a diffraction grating-based sensor system at 40 measurement points with an uncertainty below 15 μrad and a commercial triangulation sensor at 200 measurement points at surface speeds up to 300 m/s. A rotation-induced increase of two natural frequencies was measured, and their mode shapes were derived at the corresponding rotational speeds. A strain gauge was used for validation.

scholarly journals Vibration of Rotating and Revolving Planet Rings with Discrete and Partially Distributed Stiffnesses

2020 ◽  
Vol 11 (1) ◽  
pp. 127
Author(s):  
Fuchun Yang ◽  
Dianrui Wang
Keyword(s):  
High Speed ◽  
Differential Operators ◽  
Natural Frequencies ◽  
Rotation Speed ◽  
Distribution Area ◽  
Vibration Modes ◽  
Governing Equations ◽  
Vibration Properties ◽  
Wide Range ◽  
Forced Responses

Vibration properties of high-speed rotating and revolving planet rings with discrete and partially distributed stiffnesses were studied. The governing equations were obtained by Hamilton’s principle based on a rotating frame on the ring. The governing equations were cast in matrix differential operators and discretized, using Galerkin’s method. The eigenvalue problem was dealt with state space matrix, and the natural frequencies and vibration modes were computed in a wide range of rotation speed. The properties of natural frequencies and vibration modes with rotation speed were studied for free planet rings and planet rings with discrete and partially distributed stiffnesses. The influences of several parameters on the vibration properties of planet rings were also investigated. Finally, the forced responses of planet rings resulted from the excitation of rotating and revolving movement were studied. The results show that the revolving movement not only affects the free vibration of planet rings but results in excitation to the rings. Partially distributed stiffness changes the vibration modes heavily compared to the free planet ring. Each vibration mode comprises several nodal diameter components instead of a single component for a free planet ring. The distribution area and the number of partially distributed stiffnesses mainly affect the high-order frequencies. The forced responses caused by revolving movement are nonlinear and vary with a quasi-period of rotating speed, and the responses in the regions supported by partially distributed stiffnesses are suppressed.

scholarly journals Enhanced flexural properties of aramid fiber/epoxy composites by graphene oxide

2019 ◽  
Vol 8 (1) ◽  
pp. 484-492 ◽  
Author(s):  
Yinqiu Wu ◽  
Bolin Tang ◽  
Kun Liu ◽  
Xiaoling Zeng ◽  
Jingjing Lu ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Flexural Strength ◽  
Interfacial Shear Strength ◽  
Flexural Modulus ◽  
Weight Fraction ◽  
Interfacial Shear ◽  
Aramid Fiber ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Pure Epoxy

Abstract The reinforcing effect of graphene oxide (GO) in enhancing the flexural strength and flexural modulus of aramid fiber (AF)/epoxy composites were investigated with GO-AFs at a weight fraction of 0.1-0.7%. The flexural strength and flexural modulus of the composite reached 87.16 MPa and 1054.7 MPa, respectively, which were about 21.19% and 40.86% higher than those of the pure epoxy resin, respectively. In addition, the flexural properties and interfacial shear strength (IFSS) of composite reinforced by GO-AFs were much higher than the composites reinforced by AFs due to GO improved the interfacial bonding between the reinforcement material and matrix.

Comparative cytotoxicity of kaolinite, halloysite, multiwalled carbon nanotubes and graphene oxide

2021 ◽  
Vol 205 ◽  
pp. 106041
Author(s):  
Elvira Rozhina ◽  
Svetlana Batasheva ◽  
Regina Miftakhova ◽  
Xuehai Yan ◽  
Anna Vikulina ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Graphene Oxide ◽  
Multiwalled Carbon Nanotubes ◽  
Multiwalled Carbon

scholarly journals Identification of Dynamic Parameters of Pedestrian Walking Model Based on a Coupled Pedestrian–Structure System

2021 ◽  
Vol 11 (14) ◽  
pp. 6407
Author(s):  
Huiqi Liang ◽  
Wenbo Xie ◽  
Peizi Wei ◽  
Dehao Ai ◽  
Zhiqiang Zhang
Keyword(s):  
Negative Correlation ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Field Testing ◽  
The Body ◽  
Structural Vibration ◽  
Pedestrian Dynamics ◽  
Structure Interaction ◽  
Mass Spring ◽  
Stiffness And Damping

As human occupancy has an enormous effect on the dynamics of light, flexible, large-span, low-damping structures, which are sensitive to human-induced vibrations, it is essential to investigate the effects of pedestrian–structure interaction. The single-degree-of-freedom (SDOF) mass–spring–damping (MSD) model, the simplest dynamical model that considers how pedestrian mass, stiffness and damping impact the dynamic properties of structures, is widely used in civil engineering. With field testing methods and the SDOF MSD model, this study obtained pedestrian dynamics parameters from measured data of the properties of both empty structures and structures with pedestrian occupancy. The parameters identification procedure involved individuals at four walking frequencies. Body frequency is positively correlated to the walking frequency, while a negative correlation is observed between the body damping ratio and the walking frequency. The test results further show a negative correlation between the pedestrian’s frequency and his/her weight, but no significant correlation exists between one’s damping ratio and weight. The findings provide a reference for structural vibration serviceability assessments that would consider pedestrian–structure interaction effects.

scholarly journals Raman Spectroscopy Investigation of Graphene Oxide Reduction by Laser Scribing

2021 ◽  
Vol 7 (2) ◽  
pp. 48
Author(s):  
Vittorio Scardaci ◽  
Giuseppe Compagnini
Keyword(s):  
Raman Spectroscopy ◽  
Graphene Oxide ◽  
Reduce Graphene Oxide ◽  
Oxide Reduction ◽  
Material Parameters ◽  
Laser Scribing ◽  
Wide Range ◽  
Scan Speed ◽  
Laser Reduction

Laser scribing has been proposed as a fast and easy tool to reduce graphene oxide (GO) for a wide range of applications. Here, we investigate laser reduction of GO under a range of processing and material parameters, such as laser scan speed, number of laser passes, and material coverage. We use Raman spectroscopy for the characterization of the obtained materials. We demonstrate that laser scan speed is the most influential parameter, as a slower scan speed yields poor GO reduction. The number of laser passes is influential where the material coverage is higher, producing a significant improvement of GO reduction on a second pass. Material coverage is the least influential parameter, as it affects GO reduction only under restricted conditions.

Sign in / Sign up

Export Citation Format

Share Document