Orthogonal cutting of UD-CFRP using multiscale analysis: Finite element modeling

2020 ◽  
Vol 54 (18) ◽  
pp. 2505-2518
Author(s):  
Amira Hassouna ◽  
Slah Mzali ◽  
Farhat Zemzemi ◽  
Salah Mezlini
Keyword(s):  
Finite Element ◽  
Orthogonal Cutting ◽  
Micromechanical Model ◽  
Cutting Process ◽  
Machining Process ◽  
Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Homogenization Approach ◽  
Hourglass Control ◽  
Good Agreement

Unsuitable surface quality is frequently observed in the machining of composites due to their heterogeneity and anisotropic properties. Thus, minimizing the machining damages requires a thorough understanding of the machining process. In this study, two different finite element models were developed using Abaqus/Explicit to simulate the cutting process of unidirectional carbon fiber-reinforced polymer: (i) a macromechanical model based on the homogenization approach and (ii) a micromechanical model in which the composite constituents were treated separately. The effects of CFRP mechanical properties, the energy of breaking and hourglass control were analyzed using a macromechanical model. The results revealed that CFRP properties and the numerical parameters highly influenced the cutting process. A comparative study was also performed between the macromechanical and the micromechanical models to study the mechanisms of chip formation. It was demonstrated that the material removal mechanisms for both models are in good agreement with the experimental observations for different fiber orientation angles.

scholarly journals Finite Element Modeling of Fiber Reinforced Polymer-Based Wood Composites Used in Furniture Construction Considering Semi-Rigid Connections

2020 ◽  
Vol 71 (4) ◽  
pp. 339-345
Author(s):  
Mustafa Zor ◽  
Murat Emre Kartal
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Fiber Reinforced Polymer ◽  
Wood Composites ◽  
Analysis Program ◽  
The Finite Element Method ◽  
Reinforced Polymer ◽  
Engineering Designs ◽  
Control Samples ◽  
Good Agreement

In this study, control samples of pine (Pinus slyvestris L.), beech (Fagus orientalis L.) and oak (Quercus petreae L.) species were obtained by using fi ber reinforced finger corner joints. Teknobont 200 epoxy and polyvinyl (PVAc) adhesives were used as glue. Bearing in mind the critical loads that may affect their use, experimental samples were tested under diagonal loads. Experimental samples were also analyzed by a computer program using the finite element method (FEM). Finally, experimental data were compared with the results of FEM. The comparisons clearly showed that experimental results and finite element solutions (SAP2000 V17) including semi-rigid connections are in good agreement. As a structural analysis program in furniture engineering designs, FEM can be preferred in terms of reliability and cost.

Study on the stiffness degradation in concrete continuous beam with externally prestressed CFRP tendons under fatigue loading

2021 ◽  
pp. 136943322199249
Author(s):  
Xing Li ◽  
Jiwen Zhang ◽  
Jun Cheng
Keyword(s):  
Fatigue Life ◽  
Fatigue Loading ◽  
Load Level ◽  
Fiber Reinforced Polymer ◽  
Stiffness Degradation ◽  
Test Results ◽  
Reinforced Polymer ◽  
Continuous Beams ◽  
Practical Engineering ◽  
Good Agreement

This paper presents fatigue behaviors and the stiffness degradation law of concrete continuous beams with external prestressed carbon fiber-reinforced polymer (CFRP) tendons. Three specimens were tested under fatigue loading, and the influence of different load levels on the stiffness degradation and fatigue life were studied, and it was found that the stiffness degradation of three test specimens exhibited a three-stage change rule, namely rapid decrease, stable degradation, and sharp decline, but there are obvious differences in the rate and amplitude of stiffness degradation. The load level has a significant influence on the fatigue life of the test specimens. An analytical model with load level considered was proposed to calculate the residual stiffness and predict the stiffness degradation, which is in good agreement with the test results. The model of stiffness degradation presents a possible solution for practical engineering applications of concrete continuous beams with externally prestressed CFRP tendons subjected to different fatigue loadings.

Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)

2016 ◽  
Vol 857 ◽  
pp. 421-425
Author(s):  
Saif M. Thabet ◽  
S.A. Osman
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

This paper presents an investigation into the flexural behaviour of reinforced concrete beam with opening reinforced with two different materials i.e., steel and Glass Fiber Reinforced Polymer (GFRP). Comparison study between the two different materials were carried out and presented in this study through non-linear Finite Element Method (FEM) using the commercial ABAQUS 6.10 software package. The performance of the opening beam reinforced with GFRP is influenced by several key parameters. Simulation analyses were carried out to determine the behavior of beam with opening subjected to monotonic loading. The main parameters considered in this study are size of opening and reinforcement diameter. The results show that GFRP give 23%-29% more ductility than steel reinforcement. The result also shows when the size of opening change from 200mm to 150mm or from 150mm to 100mm the ultimate load capacity increase by 15%. In general, good agreement between the Finite Element (FE) simulation and the available experimental result has been obtained.

Simulation Analysis of Secondary-Load Rc Square Columns Strengthened with IFRP

2014 ◽  
Vol 501-504 ◽  
pp. 578-582
Author(s):  
Liang Hsu ◽  
Ming Long Hu ◽  
Jun Zhi Zhang
Keyword(s):  
Finite Element ◽  
Simulation Analysis ◽  
Element Model ◽  
Fiber Reinforced Polymer ◽  
Experimental Result ◽  
Compression Process ◽  
Reinforced Polymer ◽  
Secondary Load ◽  
The Impact ◽  
The Finite Element Model

Considering secondary load, simulate the axial compression process of reinforced concrete square columns strengthened with igneous rock fiber reinforced polymer with Abaqus. Make a comparison between the simulation result and experimental result. The finite-element model can simulate the experiment preferably. And the impact of lagged strain is very obvious.

Nonlinear Analysis of R.C Beams Strengthened with CFRP

2012 ◽  
Vol 166-169 ◽  
pp. 1517-1520
Author(s):  
Wen Sheng Li ◽  
Kai Wang
Keyword(s):  
Finite Element ◽  
Carbon Fiber ◽  
Nonlinear Analysis ◽  
Element Model ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Element Analysis ◽  
Flexural Performance ◽  
Reinforced Polymer ◽  
Flexural Resistance

In order to study on the flexural performances of beams strengthened with external bonded carbon fiber reinforced polymer（CFRP）sheets, nonlinear analysis is carried out by using software ANSYS. The results show that a reasonable finite element model, using a reasonable solution strategy can be a good simulation of CFRP flexural performance of reinforced concrete beams, and finite element analysis results with the experimental results have good consistency .The beams reinforced by carbon fiber polymer，the capacity of flexural resistance increased with the numbers of carbon fiber paste sheets, reinforced components of flexural capacity significantly improved, but the extent of its increase is not proportional with the numbers of carbon fiber paste sheets.

Sign in / Sign up

Export Citation Format

Share Document