Study of flow-induced fiber in-plane deformation during high pressure resin transfer molding

2021 ◽  
pp. 002199832098760
Author(s):  
Selina Zhao ◽  
William R Rodgers ◽  
Bradley Frieberg ◽  
Golam Newaz
Keyword(s):  
High Pressure ◽  
Resin Transfer Molding ◽  
Plane Deformation ◽  
Weight Ratio ◽  
Computational Prediction ◽  
Fiber Volume ◽  
Transfer Molding ◽  
Volume Fractions ◽  
Rtm Process ◽  
New Variant

High Pressure Resin Transfer Molding (HP-RTM) is a new variant of composite Resin Transfer Molding (RTM) process that enables a short cycle time and a high composite strength to weight ratio, thus presents a great potential for fabricating automotive structural parts. Due to the high injection pressure, fiber-tow washout is becoming one of the major defects which impact the properties of composite materials. To predict and mitigate the fiber-tow washout problem, approaches of both experimental process optimization and computational prediction are essential. In this paper, an experimental study of fiber-tow washout is undertaken to determine the flow injection limits beyond which the preform deformation can be observed at various fiber volume fractions. A feasibility map is developed for a specific fabric and resin combination. It provides a means to determine the injection rates and fiber volume fractions to fabricate a quality part with minimal in-plane fiber washout due to the hydrodynamically flow-induced force during the HP-RTM process.

scholarly journals Embedded Based Real-Time Monitoring in the High-Pressure Resin Transfer Molding Process for CFRP

2019 ◽  
Vol 9 (9) ◽  
pp. 1795 ◽  
Author(s):  
Kim ◽  
Kim ◽  
Hwang ◽  
Kim
Keyword(s):  
High Pressure ◽  
Real Time ◽  
Process Monitoring ◽  
High Speed ◽  
Resin Transfer Molding ◽  
Time Signal ◽  
Process Variables ◽  
Molding Process ◽  
Transfer Molding ◽  
Rtm Process

Carbon Fiber Reinforced Plastics (CFRP) is a material developed for its high strength and light weight in a broad variety of industries including aerospace, automotive, and leisure. Due to the rapid molding cycle time, high-pressure resin transfer molding (HP-RTM) processes are prone to molding defects and susceptible to various process variables such as the resin injection rate, pressure and temperature in the mold, vacuum, end-gap, pressing force, and binder. In recent years, process monitoring technology with various sensors has been applied to stabilize the HP-RTM process and control process variables. The field-programmable gate array (FPGA) based embedded monitoring system proposed in this study enabled high-speed real-time signal processing with multiple sensors, namely pressure, temperature, and linear variable differential transformer (LVDT), and proved feasibility in the field. In the HP-RTM process, the impregnation and curing of the resin were predicted from the cavity pressure and temperature variations during the injection and curing stages. In addition, the thickness of the CFRP specimen was deduced from the change in the end-gap through the detection of the LVDT signal. Therefore, the causes of molding defects were analyzed through process monitoring and the influence of molding defects on the molding quality of CFRP was investigated.

Improved tensile properties of laminates by hot-press tackifying using vacuum-assisted resin transfer molding and autoclave

2016 ◽  
Vol 35 (23) ◽  
pp. 1712-1721 ◽  
Author(s):  
Changchun Wang ◽  
Guanghui Bai ◽  
Guangquan Yue ◽  
Hongfu Li ◽  
Boming Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Properties ◽  
Resin Transfer Molding ◽  
Hot Press ◽  
Fiber Volume ◽  
Transfer Molding ◽  
Volume Fractions ◽  
Better Than

A hot-press tackifying process was used to improve the mechanical properties of cured laminates in vacuum-assisted resin transfer molding by placing a thermoplastic film into the preforms at various pressures and temperatures. Three modified preforms were prepared at 0.1, 0.3, and 0.6 MPa using an autoclave, and the laminates were then produced via vacuum-assisted resin transfer molding. The mechanical properties of the modified laminates were tested and compared to those of the unmodified ones. The fiber volume fractions of the modified laminates decreased with increasing pressure. The tensile strength of the modified laminates at the three pressures improved by 16.78%, 41.21%, and 29.47%, respectively, compared to the unmodified samples. Modified laminates at 0.3 MPa showed better results than those at 0.1 and 0.6 MPa, which were all better than the unmodified samples. The modulus of the modified laminates from vacuum-assisted resin transfer molding was improved by 2.48%, 19.01%, and 13.22%, respectively. The effect of the hot-press tackifying in improving the tensile strength and modulus of a laminate on a pre-impregnated laminate (prepreg) using the autoclave was studied and compared to that of the unmodified case. Here, the tensile strength increased by 32.5% and 12.3%, respectively.

Relaxation-Compression Resin Transfer Molding under Magnetic Field

2020 ◽  
Vol 847 ◽  
pp. 81-86
Author(s):  
Ahmed Ouezgan ◽  
Said Adima ◽  
Aziz Maziri ◽  
El Hassan Mallil ◽  
Jamal Echaabi
Keyword(s):  
Magnetic Field ◽  
Volume Fraction ◽  
Resin Transfer Molding ◽  
Molding Process ◽  
Fiber Volume ◽  
Transfer Molding ◽  
Resin Impregnation ◽  
New Variant ◽  
New Process ◽  
Compression Resin Transfer Molding

Relaxation-compression resin transfer molding under magnetic field is a new variant of VARTM (“vacuum assisted resin transfer molding”) process, which uses a flexible magnetic membrane controlled by a magnetic force, in order to govern the relaxation and compression phases by changing the permeability of the fabric preform. Thus permits to the resin to enter easily into the mold and to increase the resin impregnation velocity and the fiber volume fraction. This innovation is based on the application of the TRIZ theory (“the theory of inventive problem solving”), which allows us to answer to the shortcomings and the conflict links exist inside the VARTM processes. The objective of this paper is to present this new process and to study the effect of the current intensity and the separated gap between the flexible magnetic membrane and solenoid on the permeability of the preform.

Neural Network Based Control of Preform Permeation in Resin Transfer Molding Processes With Real-Time Permeability Estimation

2000 ◽  
Author(s):  
David Nielsen ◽  
Ranga Pitchumani
Keyword(s):  
Neural Network ◽  
Real Time ◽  
Resin Transfer Molding ◽  
Local Pressure ◽  
Transfer Molding ◽  
Model Based ◽  
Rtm Process ◽  
Virtual Sensing ◽  
Intelligent Model ◽  
Injection Pressures

Abstract Variabilities in the preform structure in situ in the mold are an acknowledged challenge to effective permeation control in the Resin Transfer Molding (RTM) process. An intelligent model-based controller is developed which utilizes real-time virtual sensing of the permeability to derive optimal decisions on controlling the injection pressures at the mold inlet ports so as to track a desired flowfront progression during resin permeation. This model-based optimal controller employs a neural network-based predictor that models the flowfront progression, and a simulated annealing-based optimizer that optimizes the injection pressures used during actual control. Preform permeability is virtually sensed in real-time, based on the flowfront velocities and local pressure gradient estimations along the flowfront. Results are presented which illustrate the ability of the controller in accurately steering the flowfront for various fill scenarios and preform geometries.

Using Computer Simulation as a Process Design Tool for Resin Injection Pultrusion (RIP)

2000 ◽  
Author(s):  
Zhongman Ding ◽  
Shoujie Li ◽  
L. James Lee ◽  
Herbert Engelen
Keyword(s):  
Modeling And Simulation ◽  
Process Design ◽  
Resin Transfer Molding ◽  
Transfer Molding ◽  
Pultrusion Process ◽  
Rtm Process ◽  
Resin Impregnation ◽  
Heating Section ◽  
Resin Injection ◽  
Resin Injection Pultrusion

Abstract Resin Injection Pultrusion (RIP) is a new composite manufacturing process, which combines the advantages of the conventional pultrusion process and the Resin Transfer Molding (RTM) process. It is sometimes referred to the Continuous Resin Transfer Molding (C-RTM) process. The RIP process differs from the conventional pultrusion process in that the resin is injected into an injection-die (instead of being placed in an open bath) in order to eliminate the emission of volatile organic compounds (styrene) (VOC) during processing. Based on the modeling and simulation of resin/fiber “pultrudability”, resin flow, and heat transfer and curing, a computer aided engineering tool has been developed for the purpose of process design. In this study, the fiber stack permeability and compressibility are measured and modeled, and the resin impregnation pattern and pressure distribution inside the fiber stack are obtained using numerical simulation. Conversion profiles in die heating section of the pultrusion die can also be obtained using the simulation tool. The correlation between the degree-of-cure profiles and the occurrence of blisters in the pultruded composite parts is discussed. Pulling force modeling and analysis are carried out to identify the effect on composite quality due to interface friction between the die surface and the moving resin/fiber mixture. Experimental data are used to verify the modeling and simulation results.

scholarly journals COMPUTATIONAL MODELING OF RTM AND LRTM PROCESSES APPLIED TO COMPLEX GEOMETRIES

2012 ◽  
Vol 11 (1-2) ◽  
pp. 93 ◽  
Author(s):  
J. Da S. Porto ◽  
M. Letzow ◽  
E. D. Dos Santos ◽  
S. C. Amico ◽  
J. A. Souza ◽  
...  
Keyword(s):  
Porous Medium ◽  
Flow Behavior ◽  
Resin Transfer Molding ◽  
Three Dimensional ◽  
Complex Geometries ◽  
Resin Flow ◽  
Transfer Molding ◽  
Rtm Process ◽  
General Terms ◽  
Filling Time

Light Resin Transfer Molding (LRTM) is a variation of the conventional manufacturing process known as Resin Transfer Molding (RTM). In general terms, these manufacturing processes consist of a closed mould with a preplaced fibrous preform through which a polymeric resin is injected, filling the mold completely, producing parts with complex geometries (in general) and good finish. Those processes differ, among other aspects, in the way that injection occurs. In the RTM process the resin is injected through discrete points whereas in LRTM it is injected into an empty channel (with no porous medium) which surrounds the entire mold perimeter. There are several numerical studies involving the RTM process but LRTM has not been explored enough by the scientific community. Based on that, this work proposes a numerical model developed in the FLUENT package to study the resin flow behavior in the LRTM process. Darcy’s law and Volume of Fluid method (VOF) are used to treat the interaction between air and resin during the flow in the porous medium, i.e. the mold filling problem. Moreover, two three-dimensional geometries were numerically simulated considering the RTM and LRTM processes. It was possible to note the huge differences about resin flow behavior and filling time between these processes to manufacture the same parts.

scholarly journals Impact and shear properties of carbon fabric/ poly-dicyclopentadiene composites manufactured by vacuum‐assisted resin transfer molding

e-Polymers ◽  
2019 ◽  
Vol 19 (1) ◽  
pp. 437-443 ◽  
Author(s):  
Hyeong Min Yoo ◽  
Moo Sun Kim ◽  
Bum Soo Kim ◽  
Dong Jun Kwon ◽  
Sung Woong Choi
Keyword(s):  
Impact Strength ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
Resin Transfer Molding ◽  
Maximum Shear Stress ◽  
Weight Percent ◽  
Fiber Volume ◽  
Shear Properties ◽  
Transfer Molding ◽  
The Impact

AbstractDicyclopentadiene (DCPD) resin has gained popularity owing to its fast curing time and ease of processing with a low viscosity in the monomer state. In the present study, the impact and shear properties of a carbon fiber (CF)/p-DCPD composite were investigated. The CF/p-DCPD composite was manufactured by vacuum-assisted resin transfer molding with CF as the reinforcement and p-DCPD as the resin with a maximum fiber volume fraction of 55 weight percent. Impact and shear properties of the CF/p-DCPD composite were evaluated and compared with those of a CF/Epoxy composite. The maximum shear stress and modulus of the CF/p-DCPD composite were lower than that of the CF/Epoxy composite. However, the CF/p-DCPD composite had higher toughness than that of the CF/Epoxy composite; this indicates that it is tougher and exhibits a more ductile load-displacement response with a lower modulus and larger failure deformation. The impact strength of the CF/p-DCPD composite was about three time that of the CF/Epoxy composite. The higher impact strength of the CF/p-DCPD composite is attributed to the resin characteristics: epoxy resin has a more brittle behavior, and hence, higher energy is required for crack propagation due to fracture.

Sliding Wear and Friction Properties of Stitched RTM Base Carbon–Carbon Composites

2005 ◽  
Author(s):  
M. K. Surappa ◽  
Kunigal N. Shivakumar
Keyword(s):  
Sliding Wear ◽  
Resin Transfer Molding ◽  
Carbon Composites ◽  
Wear Rates ◽  
Transfer Molding ◽  
Rtm Process ◽  
Composite Fabrication ◽  
Wear And Friction ◽  
Pin On Disc ◽  
Set Up

This paper presents wear and friction properties of carbon-carbon composites (CCC) manufactured by resin transfer molding (RTM) process. During composite fabrication thickness stitching was employed to improve inter laminar tension and shear properties. Wear and Friction characteristics of carbon-carbon composites were evaluated using pin-on-disc set up. Results of test indicate that surface of composites having stitches in a perpendicular direction show increase in wear rates with increase in load.

Uncertainty Modeling of Residual Stress Development in Polymeric Composites Manufactured With Resin Transfer Molding Process

2007 ◽  
Author(s):  
Kuang-Ting Hsiao
Keyword(s):  
Residual Stress ◽  
Resin Transfer Molding ◽  
Parametric Uncertainty ◽  
Polymeric Composite ◽  
Cure Kinetics ◽  
Polymeric Composites ◽  
Molding Process ◽  
Stress Development ◽  
Transfer Molding ◽  
Rtm Process

Resin Transfer Molding (RTM) is an advanced process to manufacture high quality thermoset polymeric composites. The quality of the composite depends on the resin infusion stage and the cure stage during the RTM process. The resin curing is a complex exothermic process which involves resin mechanical property evolution, resin volume shrinkage, thermal expansion, heat transfer, and chemical reaction. Since the fibers and resin have many differences in their physical properties, the composite cure stage inevitably introduces the undesired residual stress to the composite parts. As the residual stress could sometimes generate local matrix failure or degrade the performance of the composite, it is important to model and minimize the residual stress. This paper presents a model to predict the residual stress development during the composite cure process. By slightly disturbing the manufacturing parameters such as the mold heating cycle and the cure kinetics of polymer, the variations of residual stress development during the RTM process can be modeled and compared. A parametric uncertainty study of the residual stress development in the polymeric composite manufactured with RTM will be performed and discussed.

Sign in / Sign up

Export Citation Format

Share Document