The effect of boric acid on flame retardancy of intumescent flame retardant polypropylene composites including nanoclay

2021 ◽  
pp. 089270572110523
Author(s):  
Yasin Demirhan ◽  
Recep Yurtseven ◽  
Nazım Usta
Keyword(s):  
Thermal Conductivity ◽  
Boric Acid ◽  
Heat Release ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Boron Oxide ◽  
Experimental Studies ◽  
Intumescent Flame Retardant ◽  
Limiting Oxygen Index ◽  
Ul 94

In this study, different amounts of boric acid (BA, 1.25, 2.5, 3.75 and 5.0 wt%) were used to enhance the effectiveness of an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP) and pentaerythritol (PER) in polypropylene (PP) including 2 wt% montmorillonite nanoclay (MMT). Meanwhile, metaboric acid and boron oxide which were generated by the decomposition of BA appeared in the melt compounding and the burning processes, respectively. Extensive experimental studies were performed to investigate the effects of BA/boron oxide and MMT combinations on the properties of PP/IFR. The fire resistances of the composites were studied by UL 94, limiting oxygen index (LOI) and cone calorimetry tests. The thermal properties were determined by using thermogravimetric analysis, differential scanning calorimetry and thermal conductivity measurements. In addition, the mechanical properties of the composites were examined. The experimental results revealed that although the additions of 1.25 and 2.5 wt% BA with 2 wt% MMT significantly enhanced thermal and flame resistances of PP composites, 3.75 and 5.0 wt% BA additions generated antagonistic effects and deteriorated the fire resistance of the composites. The sample including 2.5 wt% BA addition achieved the best flame retardancy. The LOI value was increased from 18 to 31% with UL 94 V-0 rating. In addition, the peak heat release rate was reduced from 668.6 to 150.0 kW/m2 and the total heat release value was decreased from 247.9 to 98.4 MJ/m2. In the meantime, the thermal conductivity was increased from 0.22 up to 0.28 W/mK. Furthermore, CO, CO2 and the smoke productions were significantly decreased with respect to PP. NO generation was decreased with BA replacements. At the same time, although there was a slight decrease in the tensile strength, the flexural strength significantly increased with BA and MMT additions.

Flame Retardant Effect of a Modified Intumescent Flame Retardant on a Rigid Polyurethane Foam

2017 ◽  
Vol 748 ◽  
pp. 51-54
Author(s):  
Pei Bang Dai ◽  
Lin Ying Yang ◽  
Ting Zheng ◽  
Chang Qin ◽  
Qi Chen Tang
Keyword(s):  
Flame Retardant ◽  
Flame Retardancy ◽  
Oxygen Index ◽  
Intumescent Flame Retardant ◽  
Limiting Oxygen Index ◽  
Composite Foam ◽  
Composite Foams ◽  
Suitable Amount ◽  
Ul 94 ◽  
Pu Foams

A rigid polyurethane (PU) flame retardant composite foam was prepared by the compounding of polyols and diisocyanates with a modified intumescent flame retardant (MIFR). The MIFR was based on the three components of intumescent flame retardant normally used and was modified in a surfactant TX-10 solution. The flame retardancy of the PU flame retardant composite foams were evaluated by using the limiting oxygen index (LOI), the UL-94 (vertical flame) test and scanning electron microscopy (SEM). When MIFR was fixed at 20.0 wt% in PU/MIFR composite foams, the MIFR could enhance the flame retardancy and pass V-0 rating of UL-94 test. The microstructures observed by SEM demonstrate that a suitable amount of MIFR can promote formation of compact intumescent charred layers in PU foams.

Epoxy resin/cyanate ester composites containing DOPO and wollastonite with simultaneously improved flame retardancy and thermal resistance

2020 ◽  
Vol 32 (6) ◽  
pp. 710-718
Author(s):  
Zhengzhou Wang ◽  
Xin Gao ◽  
Wenfeng Li
Keyword(s):  
Heat Release ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Oxygen Index ◽  
Thermal Studies ◽  
Cyanate Ester ◽  
Total Heat Release ◽  
Limiting Oxygen Index ◽  
Peak Heat Release Rate ◽  
Ul 94

Flame-retardant epoxy (EP) resin/cyanate ester (CE) composites were prepared with 9,10-dihydro-9-oxa-10-phosphaphenanthrene 10-oxide (DOPO) and wollastonite (Wo). The combustion behavior of the flame-retardant EP/CE composites was investigated by limiting oxygen index (LOI), UL-94, and cone calorimeter tests. It is found that the EP/CE composite containing 7 wt% DOPO and 3 wt% Wo (sample 7DO/3Wo/EP/CE) exerts the best flame retardancy (LOI 35.5% and UL-94 V-0 rating). The peak heat release rate and total heat release of sample 7DO/3Wo/EP/CE increase slightly, while total smoke release decreases about 14% compared with the EP/CE composite containing 10 wt% DOPO (sample 10DO/EP/CE). Thermal studies indicate that the glass transition temperature and temperature at 5% mass loss of sample 7DO/3Wo/EP/CE are higher than that of sample 10DO/EP/CE. Moreover, the mechanical properties of EP/CE composites were investigated.

Investigation on the effect of supported synergistic catalyst with intumescent flame retardant in polypropylene

2021 ◽  
Vol 41 (4) ◽  
pp. 281-288
Author(s):  
Hongmei Peng ◽  
Qi Yang
Keyword(s):  
Heat Release ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Flame Retardants ◽  
Supported Catalyst ◽  
Intumescent Flame Retardant ◽  
Limiting Oxygen Index ◽  
Polypropylene Composites ◽  
Cone Calorimeter Test ◽  
Microscale Combustion Calorimetry

Abstract In this paper, cerium nitrate supported silica was prepared as a new type of catalytic synergist to improve the flame retardancy in polypropylene. When 1% of Ce(NO3)2 supported SiO2 was added, the vertical combustion performance of UL-94 of polypropylene composites was improved to V-0, the limiting oxygen index (LOI) was increased to 33.5. From the thermogravimetric analysis (TGA), the residual carbon of C and D was increased by about 6% at high temperature compared with B. When adding supported catalyst, the heat release rate (HRR) and total heat release (THR) were significantly reduced according to the microscale combustion calorimetry (MCC), the HRR of sample E with 2% synergist was the lowest. The combustion behaviors of intumescent flame retardant sample B and sample D were analyzed by cone calorimeter test (CCT), the HRR of sample D with supported synergist was significantly reduced, and the PHRR decreased from 323 kW/m2 to 264 kW/m2. The morphologies of the residue chars after vertical combustion of polypropylene composites observed by scanning electron microscopy (SEM) gave positive evidence that the supported synergist could catalyze the decomposition of intumescent flame retardants into carbon, which was the main reason for improving the flame retardancy of materials.

scholarly journals Effect of Thermal Conductive Fillers on the Flame Retardancy, Thermal Conductivity, and Thermal Behavior of Flame-Retardant and Thermal Conductive Polyamide 6

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4114 ◽  
Author(s):  
Fang Wang ◽  
Wenbo Shi ◽  
Yuliang Mai ◽  
Bing Liao
Keyword(s):  
Thermal Conductivity ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Combustion Process ◽  
Polyamide 6 ◽  
Gravimetric Analysis ◽  
Limiting Oxygen Index ◽  
Conductive Fillers ◽  
Ul 94 ◽  
The Impact

In this work, polyamide 6 (PA6) composites with improved flame retardancy and thermal conductivity were prepared with different thermal conductive fillers (TC fillers) such as aluminum nitride (AlN) and boron nitride (BN) in a PA6 matrix with aluminum diethylphosphinate (AlPi) as a fire retardant. The resultant halogen-free flame retardant (HFFR) and thermal conductive (TC) PA6 (HFFR-TC-PA6) were investigated in detail with a mechanical property test, a limiting oxygen index (LOI), the vertical burning test (UL-94), a cone calorimeter, a thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The morphology of the impact fracture surface and char residue of the composites were analyzed by scanning electron microscopy (SEM). It was found that the thermal conductivity of the HFFR-TC-PA6 composite increased with the amount of TC fillers. The TC fillers exerted a positive effect for flame retardant PA6. For example, the HFFR-TC-PA6 composites with the thickness of 1.6 mm successfully passed the UL-94 V-0 rating with an LOI of more than 29% when the loading amount of AlN-550RFS, BN-SW08 and BN-NW04 was 30 wt%. The morphological structures of the char residues revealed that TC fillers formed a highly integrated char layer surface (without holes) during the combustion process, as compared to that of flame retardant PA6/AlPi composites. In addition, the thermal stability and crystallization behavior of the composites were studied.

scholarly journals Flame Retardancy, Fire Behavior, and Flame Retardant Mechanism of Intumescent Flame Retardant EPDM Containing Ammonium Polyphosphate/Pentaerythrotol and Expandable Graphite

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4035 ◽  
Author(s):  
Junsheng Wang ◽  
Lei Xue ◽  
Bi Zhao ◽  
Guide Lin ◽  
Xing Jin ◽  
...  
Keyword(s):  
Heat Release ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Fire Behavior ◽  
Intumescent Flame Retardant ◽  
Ammonium Polyphosphate ◽  
Infrared Spectrometry ◽  
Expandable Graphite ◽  
Physical Interaction ◽  
Limiting Oxygen Index

The intumescent flame retardant ethylene–propylene–diene rubber (EPDM) was prepared using intumescent flame retardant (IFR), including ammonium polyphosphate (APP) /pentaerythrotol (PER) and expandable graphite (EG), as the flame retardant agent. The effects of IFR and EG on the flame retardancy, fire behavior, and thermal stability of the EPDM were investigated. The results show that IFR and EG have excellent synergistic flame retardant effects. When the mass ratio of IFR to EG is 3:1 and the total addition content is 40 phr, the limiting oxygen index (LOI) value of the EPDM material (EPDM/IFR/EG) can reach 30.4%, and it can pass a V-0 rating in the vertical combustion (UL-94) test. Meanwhile, during the cone calorimetry test, the heat release rate and total heat release of EPDM/IFR/EG are 69.0% and 33.3% lower than that of the pure EPDM, respectively, and the smoke release of the material also decreases significantly, suggesting that the sample shows good fire safety. In addition, the flame retardant mechanism of IFR and EG is systematically investigated by thermogravimetric analysis/infrared spectrometry (TG-IR), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM), and the results indicate that IFR and EG have only physical interaction. Moreover, the reason why IFR exhibits a poor flame retardant effect in EPDM materials is explained.

Flame Retardancy of Lanthanum Phosphinate in Combination with Intumescen Flame-Retardant in Polypropylene

2012 ◽  
Vol 490-495 ◽  
pp. 3366-3369 ◽  
Author(s):  
Cong Liu
Keyword(s):  
Thermogravimetric Analysis ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Oxygen Index ◽  
Intumescent Flame Retardant ◽  
Limiting Oxygen Index ◽  
Ul 94 ◽  
Halogen Free

The flame-retardant of Lanthanum phenylphosphinate(LaPi) was prepared and its combination with intumescent flame retardant (IFR) in polypropylene (PP) was analysed using thermogravimetric analysis (TGA), limiting oxygen index (LOI) and the UL-94 test. Compared with using IFR alone, using the combination of LaPi and IFR gained the better classification in the UL 94 test thanks to the combination of the different mechanisms. When 20 wt% loading of flame retardant of LaPi and IFR, a halogen-free V-0 PP material was achieved with a LOI of 31%.

Synergistic Flame-Retardant Effect of Aluminum Diethyl Phosphinate in PP/IFR System and the Flame-Retardant Mechanism

2021 ◽  
Vol 36 (5) ◽  
pp. 519-528
Author(s):  
J.-L. Li ◽  
C.-T. Gao ◽  
X. Sun ◽  
S.-G. Peng ◽  
Y.-W. Wang ◽  
...  
Keyword(s):  
Heat Release ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Laser Raman Spectroscopy ◽  
Mass Ratio ◽  
Limiting Oxygen Index ◽  
Laser Raman ◽  
Cone Calorimeter Test ◽  
Ul 94 ◽  
Synergistic Flame Retardant

Abstract Synergistic flame-retardant effect of aluminum diethyl phosphinate (AlPi) in intumescent flame retardant polypropylene (PP/IFR) system and the flame-retardant mechanism were investigated. The flame retardancy of PP/IFR/AlPi (the mass ratio of IFR to AlPi is 2 : 1) was the best, which was proved by the results of the limiting oxygen index (LOI) test, UL-94 test, and cone calorimeter test ( CCT) test. Here, the LOI value of the sample was as high as 34% and passed the V–0 rating in UL–94 test. The peak heat release rate (PHRR) decreased by 92.57%, the total heat release (THR) reduced by 90.52%. Thermogravimetric (TGA) data showed that the introduction of AlPi improved thermal stability and changed the thermal degradation behavior of PP/IFR composites. Interestingly, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDXS) and laser Raman spectroscopy (LRS) proved that PP/IFR/AlPi had formed more residual carbon, but the flame retardancy was worse than PP/IFR/AlPi. This is because when the mass ratio of IFR to AlPi is 2 : 1, the synergy between IFR and AlPi was significant, gas-phase flame retardant and condensed-phase flame retardant reached a balance and obtained the best flame retardant effect.

Intumescent flame retardant coating for polyamide 6,6 (PA 6,6) fabrics containing carbon nanotubes: Synergistic effect of filler on thermal stability and flame retardancy

2018 ◽  
Vol 89 (10) ◽  
pp. 2031-2040 ◽  
Author(s):  
Fanglong Zhu ◽  
QQ Feng ◽  
YF Xu ◽  
JF Hu
Keyword(s):  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Heat Release ◽  
Flame Retardant ◽  
Heat Release Rate ◽  
Flame Retardancy ◽  
Release Rate ◽  
Intumescent Flame Retardant ◽  
Flame Resistance ◽  
Limiting Oxygen Index

Flame retardant mixtures of multi-walled carbon nanotubes (MWCNTs) and intumescent flame retardant (IFR) coatings were applied to polyamide 6,6 (PA 6,6) fabrics to explore whether MWCNTs acted as a good synergist on the thermal stability and flame resistance of the IFR system. The influence of MWCNTs on the flame retardant properties and thermal degradation of the PA 6,6 fabrics were investigated by limiting oxygen index (LOI), vertical burning test (VBT), thermogravimetric analyzer (TGA), scanning electron microscopy (SEM) and cone calorimeter test (CCT). The peak heat release rate and total heat release of the IFR-PA 6,6 fabric with three kinds of wt% MWCNTs were lower than those of the only traditional IFR-PA 6,6 fabric (reduced by 74.2–76.4% and 74.3–76.5%, respectively). As compared to the traditional IFR coating, it was found that no enhancements for thermal stability and flame retardancy in terms of the ability to retard ignition were achieved for the MWCNT/IFR coating. These results demonstrated that the introduction of MWCNTs into an IFR coating can improve the flame retardancy of PA 6,6 fabric in terms of the heat release rate from CCT analysis, but it failed other burning measurements, such as LOI and VBT.

scholarly journals Synthesis of a Novel Phosphorous-Nitrogen Based Charring Agent and Its Application in Flame-retardant HDPE/IFR Composites

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 1062 ◽  
Author(s):  
Junlei Chen ◽  
Jihui Wang ◽  
Aiqing Ni ◽  
Hongda Chen ◽  
Penglong Shen
Keyword(s):  
Thermal Stability ◽  
Heat Release ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Fire Hazard ◽  
Weight Ratio ◽  
Charring Agent ◽  
Migration Percentage ◽  
Ul 94 ◽  
Thermal Stability Of

In this work, a novel phosphorous–nitrogen based charring agent named poly(1,3-diaminopropane-1,3,5-triazine-o-bicyclic pentaerythritol phosphate) (PDTBP) was synthesized and used to improve the flame retardancy of high-density polyethylene (HDPE) together with ammonium polyphosphate (APP). The results of Fourier transform infrared spectroscopy (FTIR) and 13C solid-state nuclear magnetic resonance (NMR) showed that PDTBP was successfully synthesized. Compared with the traditional intumescent flame retardant (IFR) system contained APP and pentaerythritol (PER), the novel IFR system (APP/PDTBP, weight ratio of 2:1) could significantly promote the flame retardancy, water resistance, and thermal stability of HDPE. The HDPE/APP/PDTBP composites (PE3) could achieve a UL-94 V-0 rating with LOI value of 30.8%, and had a lower migration percentage (2.2%). However, the HDPE/APP/PER composites (PE5) had the highest migration percentage (4.7%), lower LOI value of 23.9%, and could only achieve a UL-94 V-1 rating. Besides, the peak of heat release rate (PHRR), total heat release (THR), and fire hazard value of PE3 were markedly decreased compared to PE5. PE3 had higher tensile strength and flexural strength of 16.27 ± 0.42 MPa and 32.03 ± 0.59 MPa, respectively. Furthermore, the possible flame-retardant mechanism of the APP/PDTBP IFR system indicated that compact and continuous intumescent char layer would be formed during burning, thus inhibiting the degradation of substrate material and improving the thermal stability of HDPE.

Flammability and thermal properties of cotton fabrics modified with a novel flame retardant containing triazine and phosphorus components

2016 ◽  
Vol 87 (11) ◽  
pp. 1367-1376 ◽  
Author(s):  
Chaohong Dong ◽  
Zhou Lu ◽  
Peng Wang ◽  
Ping Zhu ◽  
Xuechao Li ◽  
...  
Keyword(s):  
Heat Release ◽  
Flame Retardant ◽  
Cotton Fabric ◽  
Flame Retardancy ◽  
Decomposition Temperature ◽  
Cotton Fabrics ◽  
Cone Calorimetry ◽  
Limiting Oxygen Index ◽  
Untreated Cotton ◽  
Index Value

A novel formaldehyde-free flame retardant containing phosphorus and dichlorotriazine components (CTAP) for cotton fabrics was synthesized. As an active group, the dichlorotriazine could react with cotton fabric via covalent reaction. The addition of 20.7 wt% CTAP into the cotton fabric obtained a high limiting oxygen index value of 31.5%, which was 13.5% higher than the pure cotton fabric. The results of heat release rate, total heat release and effective heat combustion indicated that CTAP effectively imparted flame retardancy to cotton fabric by the cone calorimetry test. With respect to the untreated cotton fabrics, the treated cotton fabrics degraded at lower decomposition temperature and form a consistent and compact char layer, which could be observed by thermogravimetric analysis, Fourier transform infrared spectroscopy and scanning electron microscopy. Compared to the untreated cotton fabrics, CTAP performed an effective role in flame retardancy for treated cotton fabrics. Meanwhile, it stimulated the formation of char and promoted the thermal stability of treated cotton fabrics during combustion.

Sign in / Sign up

Export Citation Format

Share Document