Sandwiched hollow sphere structures: A study of ballistic impact behavior using numerical simulation

2013 ◽  
Vol 228 (12) ◽  
pp. 2068-2078 ◽  
Author(s):  
Yibin Fu ◽  
Jun Zhou ◽  
Xiaosheng Gao
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Hollow Sphere ◽  
Ballistic Impact ◽  
Impact Behavior ◽  
Sphere Diameter ◽  
Impact Area ◽  
Impact Protection ◽  
The Impact ◽  
Sandwich Core

Sandwiched hollow sphere structure may have the potential to provide better ballistic impact protection as compared with monolithic plate based on the same weight and impact area. In the previous study of a sandwiched hollow sphere structure by the authors, a novel unit cell was created as a basic building unit of the structure, the tumbling effect was observed for significant impact energy absorption, and the existence of an optimal yield stress or hardness was proved for maximizing the impact energy absorption. However, the impact energy absorption ability of the sandwiched hollow sphere structure may also relate to many other factors. In this study, the diameter relation between the incoming projectile and the spheres in the sandwich core, the projectile initial impact velocity, and the sphere arrangement in the sandwich core are examined. It is revealed that the first layer sphere diameter should be comparable to the diameter of the incoming projectile, the diameter of spheres in different layers in one sandwich core should either decrease or increase monotonically, and there exists a critical impacting speed, at which the sandwiched sphere structure is most effective for impact energy absorption, etc. All these findings make the sandwiched hollow sphere structure a promising new member to the passive armor family.

Effect of SiO2 Nanoparticles on the Mechanical and Low Velocity Impact Properties of Epoxy/Glass Composites

2016 ◽  
Vol 838 ◽  
pp. 29-35
Author(s):  
Michał Landowski ◽  
Krystyna Imielińska
Keyword(s):  
Flexural Strength ◽  
Energy Absorption ◽  
Impact Energy ◽  
Epoxy Matrix ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Nanoparticle Suspension ◽  
Impact Properties ◽  
Velocity Impact ◽  
The Impact

Flexural strength and low velocity impact properties were investigated in terms of possibile improvements due to epoxy matrix modification by SiO2 nanoparticles (1%, 2%, 3%, 5%, 7%wt.) in glass/epoxy laminates formed using hand lay-up method. The matrix resin was Hexion L285 (DGEBA) with Nanopox A410 - SiO2 (20 nm) nanoparticle suspension in the base epoxy resin (DGEBA) supplied by Evonic. Modification of epoxy matrix by variable concentrations of nanoSiO2 does not offer significant improvements in the flexural strength σg, Young’s modulus E and interlaminar shear strength for 1% 3% and 5% nanoSiO2 and for 7% a slight drop (up to ca. 15-20%) was found. Low energy (1J) impact resistance of nanocomposites represented by peak load in dynamic impact characteristics was not changed for nanocompoosites compared to the unmodified material. However at higher impact energy (3J) nanoparticles appear to slightly improve the impact energy absorption for 3% and 5%. The absence or minor improvements in the mechanical behaviour of nanocomposites is due to the failure mechanisms associated with hand layup fabrication technique: (i.e. rapid crack propagation across the extensive resin pockets and numerous pores and voids) which dominate the nanoparticle-dependent crack energy absorption mechanisms (microvoids formation and deformation).

Interplay of fabric structure and shear thickening fluid impregnation in moderating the impact response of high-performance woven fabrics

2020 ◽  
Vol 54 (28) ◽  
pp. 4387-4395
Author(s):  
Sanchi Arora ◽  
Abhijit Majumdar ◽  
Bhupendra Singh Butola
Keyword(s):  
Beneficial Effect ◽  
Energy Absorption ◽  
Impact Energy ◽  
High Performance ◽  
Research Work ◽  
Impact Resistance ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Fabric Structure ◽  
The Impact

The beneficial effect of STF impregnation in enhancing the impact resistance of high-performance fabrics has been extensively reported in the literature. However, this research work reports that fabric structure has a decisive role in moderating the effectiveness of STF impregnation in terms of impact energy absorption. Plain woven fabrics having sett varying from 25 × 25 inch−1 to 55 × 55 inch−1 were impregnated with STF at two different padding pressures to obtain different add-ons. The impact energy absorption by STF impregnated loosely woven fabrics was found to be higher than that of their neat counterparts for both levels of add-on, while opposite trend was observed in case of tightly woven fabrics. Further, comparison of tightly woven plain, 2/2 twill, 3/1 twill and 2 × 2 matt fabrics revealed beneficial effect of STF impregnation, except for the plain woven fabric, establishing that there exists a fabric structure-STF impregnation interplay that tunes the impact resistance of woven fabrics.

Energy absorption from composite reinforced with high performance auxetic textile structure

2020 ◽  
pp. 002199832096455
Author(s):  
Fernanda Steffens ◽  
Fernando Ribeiro Oliveira ◽  
Raul Fangueiro
Keyword(s):  
Energy Absorption ◽  
High Performance ◽  
Poisson Ratio ◽  
Impact Behavior ◽  
Knitted Fabrics ◽  
Reinforced Composite ◽  
Composite Fabrication ◽  
Impact Experiment ◽  
Key Factor ◽  
The Impact

The objective of this study is to analyze the impact behavior on the basis of energy approach of weft knitted structures, namely a jersey composite and an auxetic composite using high performance yarns. Weft knitted fabrics were produced with the same structural and machine parameters, using 100% para-aramid and hybrid (47% para-aramid and 53% polyamide) structure. Composite fabrication was achieved through hand lay-up using epoxy resin. Negative Poisson ratio of the reinforcing auxetic fabric was transferred from the fabric to the composite developed. Results obtained by drop weight dart impact test show that the impact experiment with different impact loads confirmed the auxetic composites, regardless de material composition, have an increase in the total energy absorption compared to jersey reinforced composite, approximately 2.5 and 4 times more for para-aramid and hybrid composite, respectively. Auxetic composites developed within this work present great potential for applications in different areas, mainly where energy absorption is a key factor to be considered, such as in protection, sports among others.

Dynamic Energy Absorption Performances of Rain Forest Vehicle (RFV) under Frontal Impact

2014 ◽  
Vol 67 (3) ◽  
Author(s):  
M. S. Othman ◽  
Z. Ahmad
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Loading ◽  
Rain Forest ◽  
Experimental Testing ◽  
Rigid Wall ◽  
Crash Analysis ◽  
Frontal Impact ◽  
Frontal Section ◽  
The Impact

This paper treats the crash analysis and energy absorption response of Rain Forest Vehicle (RFV) subjected to frontal impact scenario namely impacting rigid wall and column. Dynamic computer simulation techniques validated by experimental testing are used to carry out a crash analysis of such vehicle. The study aims at quantifying the energy absorption capability of frontal section of RFV under impact loading, for variations in the load transfer paths and geometry of the crashworthy components. It is evident that the proposed design of the RFV frontal section are desirable as primary impact energy mitigation due to its ability to withstand and absorb impact loads effectively. Furthermore, it is found that the impact energy transmitted to the survival room may feasibly be minimized in these two impact events. The primary outcome of this study is design recommendation for enhancing the level of safety of the off-road vehicle where impact loading is expected.   

Dynamic Energy Absorption Performances of Rain Forest Vehicle (RFV) under Frontal Impact

2014 ◽  
Vol 69 (3) ◽  
Author(s):  
M. S. Othman ◽  
Z. Ahmad
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Loading ◽  
Rain Forest ◽  
Experimental Testing ◽  
Rigid Wall ◽  
Crash Analysis ◽  
Frontal Impact ◽  
Frontal Section ◽  
The Impact

This paper treats the crash analysis and energy absorption response of Rain Forest Vehicle (RFV) subjected to frontal impact scenario namely impacting rigid wall and column. Dynamic computer simulation techniques validated by experimental testing are used to carry out a crash analysis of such vehicle. The study aims at quantifying the energy absorption capability of frontal section of RFV under impact loading, for variations in the load transfer paths and geometry of the crashworthy components. It is evident that the proposed design of the RFV frontal section are desirable as primary impact energy mitigation due to its ability to withstand and absorb impact loads effectively. Furthermore, it is found that the impact energy transmitted to the survival room may feasibly be minimized in these two impact events. The primary outcome of this study is design recommendation for enhancing the level of safety of the off-road vehicle where impact loading is expected.   

Low-velocity impact response of wood-strand sandwich panels and their components

Holzforschung ◽  
2018 ◽  
Vol 72 (8) ◽  
pp. 681-689 ◽  
Author(s):  
Mostafa Mohammadabadi ◽  
Vikram Yadama ◽  
LiHong Yao ◽  
Debes Bhattacharyya
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Failure Modes ◽  
Sandwich Panels ◽  
Low Velocity Impact ◽  
Insulation Material ◽  
Low Velocity ◽  
Velocity Impact ◽  
Section Modulus ◽  
The Impact

AbstractProfiled hollow core sandwich panels (SPs) and their components (outer layers and core) were manufactured with ponderosa and lodgepole pine wood strands to determine the effects of low-velocity impact forces and to observe their energy absorption (EA) capacities and failure modes. An instrumented drop weight impact system was applied and the tests were performed by releasing the impact head from 500 mm for all the specimens while the impactors (IMPs) were equipped with hemispherical and flat head cylindrical heads. SPs with cavities filled with a rigid foam insulation material (SPfoam) were also tested to understand the change in EA behavior and failure mode. Failure modes induced by both IMPs to SPs were found to be splitting, perforating, penetrating, core crushing and debonding between the core and the outer layers. SPfoams absorbed 26% more energy than unfilled SPs. SPfoams with urethane foam suffer less severe failure modes than SPs. SPs in a ridge-loading configuration absorbed more impact energy than those in a valley-loading configuration, especially when impacted by a hemispherical IMP. Based on the results, it is evident that sandwich structure is more efficient than a solid panel concerning impact energy absorption, primarily due to a larger elastic section modulus of the core’s corrugated geometry.

Dynamic Fracture Analysis of Aluminum Honeycomb Sandwich Panel

2006 ◽  
Vol 306-308 ◽  
pp. 67-72 ◽  
Author(s):  
Byung Il Kim ◽  
Byeong Wook Noh ◽  
Young Woo Choi ◽  
Sung In Bae ◽  
Jung I. Song
Keyword(s):  
Impact Energy ◽  
Sandwich Panel ◽  
Bending Test ◽  
Face Sheet ◽  
Impact Behavior ◽  
Lower Face ◽  
Short Edge ◽  
Edge Direction ◽  
Aluminum Honeycomb ◽  
The Impact

Impact behaviors of Aluminum Honeycombs Sandwich Panel (AHSP) by drop weight test were investigated in this study. Two types of specimens with l/2" and l/4" cell size were tested by two impactors with the weight of 5.25kgf and 11.9kgf respectively. Transient, contact and elastic-plastic analyses were performed by finite element method. Impact behavior of AHSP about impact sites appeared nearly the same in low impact energy, but it was different in high impact energy. Face was the strongest about impact and short-edge was the weakest. The damaged area of AHSP was enlarged with the increase of impactor weight that is corresponding to impact energy. After 3-point bending test, fracture modes of AHSP were analyzed with AE counts, lower face sheet was fractured in the long-edge direction first, and then separation between face sheet and core happened. In the short-edge direction after core wrinkled, lower face sheet was torn, impact behavior by FE analysis were increased localized damage in high velocity because the faster velocity of the impact was, the smaller the stress of core was. Consequently, impactor weight had an effect on widely damaged area, while the impact velocity gave rise to localized damaged area.

Numerical Investigation on Impact Energy Absorption of Single-Walled Carbon Nanotube Reinforced Composites

2012 ◽  
Author(s):  
Lingyu Sun ◽  
Jian Zhang ◽  
Dingxin Leng
Keyword(s):  
Numerical Investigation ◽  
Energy Absorption ◽  
Impact Energy ◽  
Metal Matrix ◽  
Failure Modes ◽  
Volume Fraction ◽  
Matrix Material ◽  
Reinforced Composites ◽  
Alloy Matrix ◽  
The Impact

With the exceptional mechanical properties, carbon nanotubes (CNTs) are considered to be attractive candidate reinforcements for composite materials and to have potential applications in improving the energy absorption capability of matrix material. However, it is still difficult to reveal the micro-mechanisms of the impact energy absorption of CNT-reinforced composites by experiments, hence, the numerical investigation is helpful. In this paper, a unit cell of single-walled CNTs (SWCNTs) embedded in metal matrix is modeled by nano-scale finite element method. Under impact loads, the failure modes of a single SWCNT and the SWCNT in matrix are predicted, respectively, and several possible energy absorption mechanisms are explained and compared. The investigation shows that, the metal matrix restraints the radial expansion of the SWCNT and therefore improves its crush buckling resistance, and makes it absorb more energy before collapse. The specific energy absorption of SWCNTs-reinforce composites increases with the increasing volume fraction of SWCNTs in both matrixes, and ascends more quickly in magnesium alloy than in aluminum alloy matrix.

Sign in / Sign up

Export Citation Format

Share Document