Low-velocity impact response of wood-strand sandwich panels and their components

Holzforschung ◽  
2018 ◽  
Vol 72 (8) ◽  
pp. 681-689 ◽  
Author(s):  
Mostafa Mohammadabadi ◽  
Vikram Yadama ◽  
LiHong Yao ◽  
Debes Bhattacharyya
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Failure Modes ◽  
Sandwich Panels ◽  
Low Velocity Impact ◽  
Insulation Material ◽  
Low Velocity ◽  
Velocity Impact ◽  
Section Modulus ◽  
The Impact

AbstractProfiled hollow core sandwich panels (SPs) and their components (outer layers and core) were manufactured with ponderosa and lodgepole pine wood strands to determine the effects of low-velocity impact forces and to observe their energy absorption (EA) capacities and failure modes. An instrumented drop weight impact system was applied and the tests were performed by releasing the impact head from 500 mm for all the specimens while the impactors (IMPs) were equipped with hemispherical and flat head cylindrical heads. SPs with cavities filled with a rigid foam insulation material (SPfoam) were also tested to understand the change in EA behavior and failure mode. Failure modes induced by both IMPs to SPs were found to be splitting, perforating, penetrating, core crushing and debonding between the core and the outer layers. SPfoams absorbed 26% more energy than unfilled SPs. SPfoams with urethane foam suffer less severe failure modes than SPs. SPs in a ridge-loading configuration absorbed more impact energy than those in a valley-loading configuration, especially when impacted by a hemispherical IMP. Based on the results, it is evident that sandwich structure is more efficient than a solid panel concerning impact energy absorption, primarily due to a larger elastic section modulus of the core’s corrugated geometry.

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

Effect of SiO2 Nanoparticles on the Mechanical and Low Velocity Impact Properties of Epoxy/Glass Composites

2016 ◽  
Vol 838 ◽  
pp. 29-35
Author(s):  
Michał Landowski ◽  
Krystyna Imielińska
Keyword(s):  
Flexural Strength ◽  
Energy Absorption ◽  
Impact Energy ◽  
Epoxy Matrix ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Nanoparticle Suspension ◽  
Impact Properties ◽  
Velocity Impact ◽  
The Impact

Flexural strength and low velocity impact properties were investigated in terms of possibile improvements due to epoxy matrix modification by SiO2 nanoparticles (1%, 2%, 3%, 5%, 7%wt.) in glass/epoxy laminates formed using hand lay-up method. The matrix resin was Hexion L285 (DGEBA) with Nanopox A410 - SiO2 (20 nm) nanoparticle suspension in the base epoxy resin (DGEBA) supplied by Evonic. Modification of epoxy matrix by variable concentrations of nanoSiO2 does not offer significant improvements in the flexural strength σg, Young’s modulus E and interlaminar shear strength for 1% 3% and 5% nanoSiO2 and for 7% a slight drop (up to ca. 15-20%) was found. Low energy (1J) impact resistance of nanocomposites represented by peak load in dynamic impact characteristics was not changed for nanocompoosites compared to the unmodified material. However at higher impact energy (3J) nanoparticles appear to slightly improve the impact energy absorption for 3% and 5%. The absence or minor improvements in the mechanical behaviour of nanocomposites is due to the failure mechanisms associated with hand layup fabrication technique: (i.e. rapid crack propagation across the extensive resin pockets and numerous pores and voids) which dominate the nanoparticle-dependent crack energy absorption mechanisms (microvoids formation and deformation).

scholarly journals Low Velocity Impact Assessment of a Carbon Fiber Bicycle Wheel

2021 ◽  
Author(s):  
Karmanya Ratra
Keyword(s):  
Carbon Fiber ◽  
Energy Absorption ◽  
Impact Energy ◽  
Damage Evolution ◽  
Impact Damage ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Test Protocol ◽  
Velocity Impact ◽  
The Impact

Carbon fiber bicycle wheels were tested under low velocity impact to monitor the damage evolution of the impact event. A wheel model designed by KQS Inc. (industrial partner) with eight different configurations, including spoke tension, number of spokes, and location of impact on the rim were investigated. IR thermography combined with PCA was used to monitor the damage during impact. Results showed that wheels in line with spokes had 16% higher impact energy absorption compared to those impacted in between spokes on average (58.9 J vs 70.2 J). The 20 spoked wheels had a slightly higher (6%) impact energy absorption than the 24 spoked wheels. The added stiffness due to the extra spokes reduced the impact energy absorption of rim. Wheels with higher spoke tension also had slightly improved impact energy absorption (4%). The test protocol established in this study provides a good understanding of the wheel’s impact damage evolution.

scholarly journals Low-Velocity Impact Resistance of Al/Gf/PP Laminates with Different Interface Performance

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4416
Author(s):  
Yanyan Lin ◽  
Huaguan Li ◽  
Zhongwei Zhang ◽  
Jie Tao
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Load ◽  
Rear Surface ◽  
Impact Resistance ◽  
Nitrogen Plasma ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact

The weak interface performance between metal and composite (IPMC) makes the composite materials susceptible to impact load. Aluminum/glass fiber/polypropylene (Al/Gf/PP) laminates were manufactured with the aluminum alloy sheets modified by nitrogen plasma surface treatment and the phosphoric acid anodizing method, respectively. FEM models of Al/Gf/PP laminates under low-velocity impact were established in ABAQUS/Explicit based on the generated data including the model I and II interlaminar fracture toughness. Low-velocity impact tests were performed to investigate the impact resistance of Al/Gf/PP laminates including load traces, failure mechanism, and energy absorption. The results showed that delamination was the main failure mode of two kinds of laminates under the impact energy of 20 J and 30 J. When the impact energy was between 40 J and 50 J, there were metal cracks on the rear surface of the plasma pretreated specimens, which possessed higher energy absorption and impact resistance, although the integrity of the laminates could not be preserved. Since the residual compressive stress was generated during the cooling process, the laminates were more susceptible to stretching rather than delamination. For impact energy (60 J) causing the through-the-thickness crack of two kinds of laminates, plasma pretreated specimens exhibited higher SEA values close to 9 Jm2/kg due to better IPMC. Combined with the FEM simulation results, the interface played a role in stress transmission and specimens with better IPMC enabled the laminates to absorb more energy.

Effect of Graphene Platelets/Fiber on Plastics Nanocomposites under Low-Velocity Impact Response

2016 ◽  
Vol 852 ◽  
pp. 23-28
Author(s):  
S. Subha ◽  
Battu Sai Krishna ◽  
Dalbir Singh ◽  
R. Gokulnath
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Laminate Plate ◽  
Absorption Capacity ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Energy Absorption Capacity ◽  
Velocity Impact ◽  
The Impact

In this study, an attempt has made to explore the low-velocity impact response of a Carbon/epoxy laminate (CFRP) and E-Glass/epoxy laminates (GFRP). The composite was reinforced with Graphene Nanoplatelets (GnPs) and impact energy absorption capacity was studied. The plain GFRP and plain CFRP were served as a baseline for comparison. These composite laminate plates were fabricated using hand layup technique. The tests were carried out on the laminate plate as per ASTM D5628 FD. Impact tests were performed using a specially designed vertical drop-weight testing machine with an impactor mass of 1.926 kg. The result shows that laminate plate reinforced with GnPs reinforcement enhances the impact energy absorption capacity of the composites almost 4.5 % in the case Carbon/epoxy laminate and 3.5 % in the case of and E-glass/epoxy laminate. The enhanced impact resistance could be attributed to increased interlaminar fracture toughness of the fibres.

Experimental Investigation Into the Effect of Impact Loading on the Response of Metallic Trapezoidal Corrugated Core Sandwich Panels

2018 ◽  
Author(s):  
Haifu Yang ◽  
Yuansheng Cheng ◽  
Pan Zhang ◽  
Jun Liu ◽  
Kai Chen
Keyword(s):  
Dynamic Response ◽  
Impact Energy ◽  
Impact Loading ◽  
Sandwich Panels ◽  
Low Velocity Impact ◽  
Front Face ◽  
Low Velocity ◽  
Velocity Impact ◽  
Impact Location ◽  
The Impact

Sandwich structures with corrugated cores have attracted a lot of interest from industrial and academic fields due to their superior crashworthiness. In this paper, the dynamic response of metallic trapezoidal corrugated core sandwich panels under low-velocity impact loading is studied by conducting drop hammer impact testing. The sandwich panels composed of two thin face skins and trapezoidal corrugated core, were designed and fabricated through folding and laser welding technology. Main attention of present study was placed at the influences of the impact energy, impactor diameter and impact location on the impact force, deformation mechanisms and the permanent deflections of the trapezoidal corrugated core sandwich panels. Results revealed that the impact energy has significant effects on the dynamic response of the sandwich panel, whereas the impact diameter has little effects on it. The deformation mode of the front face sheet differs sharply when the impact location is different. The middle unit cell of corrugated core is compressed to the “M” shape under different low-velocity impact loading.

scholarly journals Low Velocity Impact Assessment of a Carbon Fiber Bicycle Wheel

2021 ◽  
Author(s):  
Karmanya Ratra
Keyword(s):  
Carbon Fiber ◽  
Energy Absorption ◽  
Impact Energy ◽  
Damage Evolution ◽  
Impact Damage ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Test Protocol ◽  
Velocity Impact ◽  
The Impact

Carbon fiber bicycle wheels were tested under low velocity impact to monitor the damage evolution of the impact event. A wheel model designed by KQS Inc. (industrial partner) with eight different configurations, including spoke tension, number of spokes, and location of impact on the rim were investigated. IR thermography combined with PCA was used to monitor the damage during impact. Results showed that wheels in line with spokes had 16% higher impact energy absorption compared to those impacted in between spokes on average (58.9 J vs 70.2 J). The 20 spoked wheels had a slightly higher (6%) impact energy absorption than the 24 spoked wheels. The added stiffness due to the extra spokes reduced the impact energy absorption of rim. Wheels with higher spoke tension also had slightly improved impact energy absorption (4%). The test protocol established in this study provides a good understanding of the wheel’s impact damage evolution.

scholarly journals Structural Damage Characteristics of a Layer-to-Layer 3-D Angle-Interlock Woven Composite Subjected to Drop-Weight Impact

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Qian Ma ◽  
Ke Wang ◽  
Shudong Wang ◽  
Yiwei Ouyang ◽  
Zhiqiang Lin ◽  
...  
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Structural Damage ◽  
Low Velocity Impact ◽  
Woven Composite ◽  
Low Velocity ◽  
Velocity Impact ◽  
Damage Characteristics ◽  
Drop Weight ◽  
The Impact

AbstractThe most attractive structural feature of the three-dimensional (3D) angle-interlock woven structure is that the straight weft yarns are bundled by the undulated warp yarns, which induces the overall good structural stability and a stable fabric structure. Thus the 3-D angle-interlock woven composite (3DAWC) prepared by the vacuum-assisted resin transfer molding (VARTM) curing process has excellent mechanical properties by using the fabric and epoxy resin as the reinforcement and matrix, respectively. The low-velocity impact damage properties of the composites under different drop-weight energies (70, 80, and 100 J) were tested experimentally. The load–displacement curves, energy–time curves, and the ultimate failure modes were obtained to analyze the performance of resistance to low-velocity impact, as well as the impact energy absorption effect and failure mechanism, especially the structural damage characteristics of the 3DAWC subjected to the low-velocity impact of drop weight. By analyzing the obtained experimental results, it is found that the fabric reinforcement is the primary energy absorption component and the impact energy mainly propagates along the longitudinal direction of the yarns, especially the weft yarn system, which is arranged in a straight way. In addition, as the impact energy increases, the energy absorbed and dissipated by the composite increases simultaneously. This phenomenon is manifested in the severity of deformation and damage of the material, i.e., the amount of deformation and size of the damaged area.

Impact Energy for the First Crack of Reinforced Concrete with Partial Replacements of Sand by Fine Crumb Rubber

2013 ◽  
Vol 701 ◽  
pp. 286-290 ◽  
Author(s):  
Mustafa Maher Al-Tayeb ◽  
B.H. Abu Bakar ◽  
Hanafi Ismail ◽  
Hazizan Md Akil
Keyword(s):  
Reinforced Concrete ◽  
Impact Energy ◽  
Impact Loading ◽  
Crumb Rubber ◽  
Low Velocity Impact ◽  
Moist Air ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact

Effects of partial replacements of sand by waste fine crumb rubber on the performance of reinforced concrete under low velocity impact loading were investigated. Specimens were prepared for 5%, 10% and 20 % replacements by volume of sand. All specimens were cured in moist air for 90 days. For each case, six beams of 100 mm ×100 mm × 500mm were subjected to 5.15 kg hammer from 900mm height. The number of blows of the hammer required to induce the first visible crack of the beam were recorded. The results are presented in terms of impact energy required for the first crack. The fine crumb rubbers increased the impact energy for first crack.

scholarly journals The low-velocity impact and compression after impact (CAI) behavior of foam core sandwich panels with shape memory alloy hybrid face-sheets

2019 ◽  
Vol 26 (1) ◽  
pp. 517-530 ◽  
Author(s):  
Ye Wu ◽  
Yun Wan
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Sandwich Panels ◽  
Image Correlation ◽  
Low Velocity Impact ◽  
Foam Core ◽  
Low Velocity ◽  
Velocity Impact ◽  
Compression After Impact ◽  
The Impact

AbstractDue to the properties of shape memory effect and super-elasticity, shape memory alloy (SMA) is added into glass fiber reinforced polymer (GFRP) face-sheets of foam core sandwich panels to improve the impact resistence performance by many researchers. This paper tries to discuss the failure mechanism of sandwich panels with GF/ epoxy face-sheets embedded with SMA wires and conventional 304 SS wire nets under low-velocity impact and compression after impact (CAI) tests. The histories of contact force, absorbed energy and deflection during the impact process are obtained by experiment. Besides, the failure modes of sandwich panels with different ply modes are compared by visual inspection and scanning electron microscopy (SEM). CAI tests are conducted with the help of digital image correlation (DIC) technology. Based on the results, the sandwich panels embedded with SMA wires can absorb more impact energy, and show relatively excellent CAI performance. This is because the SMA wires can absorb and transmit the energy to the outer region of GFRP face-sheet due to the super-elasticity-behavior. The failure process and mechanism of the CAI test is also discussed.

Sign in / Sign up

Export Citation Format

Share Document