scholarly journals Efficient experimental identification of three-dimensional tyre structural properties

2018 ◽  
Vol 233 (1) ◽  
pp. 88-106 ◽  
Author(s):  
Vasilis Tsinias ◽  
George Mavros
Keyword(s):  
Structural Parameters ◽  
Three Dimensional ◽  
Partial Identification ◽  
Modal Testing ◽  
Mode Shapes ◽  
Experimental Identification ◽  
Frequency Responses ◽  
Angular Dependency ◽  
High Purity Mode ◽  
Generic Time

Modal testing is routinely applied to tyres for the identification of structural parameters and prediction of their vibration response to excitations. The present work focuses on the more demanding case of modal testing with the aim of constructing a full mathematical model of a tyre, appropriate for use in a generic time-based simulation. For this purpose, the less common free–free boundary condition is employed for the wheel, while the tyre belt is excited in all three directions, namely radial tangential and lateral. To improve efficiency, a novel partial identification method is developed for the mode shapes, whereby measured and predicted frequency responses are matched around distinct resonance peaks, while eliminating the effect of out-of-band modes. Axial symmetry of the tyre requires high purity mode shapes to avoid angular dependency of the tyre’s response. For this reason, experimental mode shapes are digitally filtered and combined with their orthogonal counterparts. Processed data reveal apparent repetition of selected mode shapes, and this is attributed to rim deflection.

scholarly journals Brain capillary structures of schizophrenia cases and controls show a correlation with their neuron structures

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Rino Saiga ◽  
Masayuki Uesugi ◽  
Akihisa Takeuchi ◽  
Kentaro Uesugi ◽  
Yoshio Suzuki ◽  
...  
Keyword(s):  
Blood Vessels ◽  
Structural Parameters ◽  
Three Dimensional ◽  
Superior Temporal Gyrus ◽  
Anterior Cingulate ◽  
Dimensional Structure ◽  
Constant Diameter ◽  
The Mean ◽  
Cartesian Coordinate ◽  
Micrometer Scale

AbstractBrain blood vessels constitute a micrometer-scale vascular network responsible for supply of oxygen and nutrition. In this study, we analyzed cerebral tissues of the anterior cingulate cortex and superior temporal gyrus of schizophrenia cases and age/gender-matched controls by using synchrotron radiation microtomography or micro-CT in order to examine the three-dimensional structure of cerebral vessels. Over 1 m of cerebral blood vessels was traced to build Cartesian-coordinate models, which were then used for calculating structural parameters including the diameter and curvature of the vessels. The distribution of vessel outer diameters showed a peak at 7–9 μm, corresponding to the diameter of the capillaries. Mean curvatures of the capillary vessels showed a significant correlation to the mean curvatures of neurites, while the mean capillary diameter was almost constant, independent of the cases. Our previous studies indicated that the neurites of schizophrenia cases are thin and tortuous compared to controls. The curved capillaries with a constant diameter should occupy a nearly constant volume, while neurons suffering from neurite thinning should have reduced volumes, resulting in a volumetric imbalance between the neurons and the vessels. We suggest that the observed structural correlation between neurons and blood vessels is related to neurovascular abnormalities in schizophrenia.

scholarly journals Coupled Fluid–Solid Numerical Simulation for Flow Field Characteristics and Supporting Performance of Flexible Support Cylindrical Gas Film Seal

Aerospace ◽  
2021 ◽  
Vol 8 (4) ◽  
pp. 97
Author(s):  
Junfeng Sun ◽  
Meihong Liu ◽  
Zhen Xu ◽  
Taohong Liao ◽  
Xiangping Hu ◽  
...  
Keyword(s):  
Flow Field ◽  
Film Thickness ◽  
Fluid Dynamic ◽  
Structural Characteristics ◽  
Structural Parameters ◽  
Equivalent Stress ◽  
Three Dimensional ◽  
High Rotational Speed ◽  
Flexible Support ◽  
Flow Field Characteristics

A new type of cylindrical gas film seal (CGFS) with a flexible support is proposed according to the working characteristics of the fluid dynamic seal in high-rotational-speed fluid machinery, such as aero-engines and centrifuges. Compared with the CGFS without a flexible support, the CGFS with flexible support presents stronger radial floating characteristics since it absorbs vibration and reduces thermal deformation of the rotor system. Combined with the structural characteristics of a film seal, an analytical model of CGFS with a flexible wave foil is established. Based on the fluid-structure coupling analysis method, the three-dimensional flow field of a straight-groove CGFS model is simulated to study the effects of operating and structural parameters on the steady-state characteristics and the effects of gas film thickness, eccentricity, and the number of wave foils on the equivalent stress of the flexible support. Simulation results show that the film stiffness increases significantly when the depth of groove increases. When the gas film thickness increases, the average equivalent stress of the flexible support first decreases and then stabilizes. Furthermore, the number of wave foils affects the average foils thickness. Therefore, when selecting the number of wave foils, the support stiffness and buffer capacity should be considered simultaneously.

scholarly journals Identification of Mode Shapes of a Composite Cylinder Using Convolutional Neural Networks

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2801
Author(s):  
Bartosz Miller ◽  
Leonard Ziemiański
Keyword(s):  
Neural Networks ◽  
Convolutional Neural Networks ◽  
Composite Structures ◽  
Three Dimensional ◽  
Mode Shapes ◽  
Identification Algorithm ◽  
Material Degradation ◽  
Local Material ◽  
Noisy Input ◽  
Shape Vector

The aim of the following paper is to discuss a newly developed approach for the identification of vibration mode shapes of multilayer composite structures. To overcome the limitations of the approaches based on image analysis (two-dimensional structures, high spatial resolution of mode shapes description), convolutional neural networks (CNNs) are applied to create a three-dimensional mode shapes identification algorithm with a significantly reduced number of mode shape vector coordinates. The CNN-based procedure is accurate, effective, and robust to noisy input data. The appearance of local damage is not an obstacle. The change of the material and the occurrence of local material degradation do not affect the accuracy of the method. Moreover, the application of the proposed identification method allows identifying the material degradation occurrence.

Free Vibrations of Thick, Complete Conical Shells of Revolution From a Three-Dimensional Theory

2005 ◽  
Vol 72 (5) ◽  
pp. 797-800 ◽  
Author(s):  
Jae-Hoon Kang ◽  
Arthur W. Leissa
Keyword(s):  
Ritz Method ◽  
Three Dimensional ◽  
Axial Direction ◽  
Free Vibrations ◽  
Mode Shapes ◽  
Vibration Frequencies ◽  
Shells Of Revolution ◽  
Dimensional Theory ◽  
Conical Shells ◽  
Cylindrical Coordinate

A three-dimensional (3D) method of analysis is presented for determining the free vibration frequencies and mode shapes of thick, complete (not truncated) conical shells of revolution in which the bottom edges are normal to the midsurface of the shells based upon the circular cylindrical coordinate system using the Ritz method. Comparisons are made between the frequencies and the corresponding mode shapes of the conical shells from the authors' former analysis with bottom edges parallel to the axial direction and the present analysis with the edges normal to shell midsurfaces.

scholarly journals Comparison of Two Numerical Algorithms for Computing the Effects of Mistuning of Fan Flutter

2016 ◽  
Author(s):  
L. Salles ◽  
M. Vahdati
Keyword(s):  
Numerical Models ◽  
Three Dimensional ◽  
Numerical Algorithms ◽  
Mode Shapes ◽  
Minimal Amount ◽  
Aeroelastic System ◽  
Cpu Time ◽  
Influence Coefficients ◽  
Non Linear ◽  
The Time Domain

The aim of this paper is to study the effects of mistuning on fan flutter and to compare the prediction of two numerical models of different fidelity. The high fidelity model used here is a three-dimensional, whole assembly, time-accurate, viscous, finite-volume compressible flow solver. The Code used for this purpose is AU3D, written in Imperial College and validated for flutter computations over many years. To the best knowledge of authors, this is the first time such computations have been attempted. This is due to the fact that, such non-linear aeroelastic computations with mistuning require large amount of CPU time and cannot be performed routinely and consequently, faster (low fidelity) models are required for this task. Therefore, the second model used here is the aeroelastic fundamental mistuning model (FMM) and it based on an eigenvalue analysis of the linearized modal aeroelastic system with the aerodynamic matrix calculated from the aerodynamic influence coefficients. The influence coefficients required for this algorithm are obtained from the time domain non-linear Code by shaking one blade in the datum (tuned) frequency and mode. Once the influence coefficients have been obtained, the computations of aero damping require minimal amount of CPU time and many different mistuning patterns can be studied. The objectives of this work are to: 1. Compare the results between the two models and establish the capabilities/limitations of aeroelastic FMM, 2. Check if the introduction of mistuning would bring the experimental and computed flutter boundaries closer, 3. Establish a relationship between mistuning and damping. A rig wide-chord fan blade, typical of modern civil designs, was used as the benchmark geometry for this study. All the flutter analyses carried out in this paper are with frequency mistuning, but the possible consequences of mistuned mode shapes are briefly discussed at the end of this paper. Only the first family of modes (1F, first flap) is considered in this work. For the frequency mistuning analysis, the 1F frequency is varied around the annulus but the 1F mode shapes remain the same for all the blades. For the mode shape mistuning computations, an FE analysis of the whole assembly different mass blades is performed. The results of this work clearly show the importance of mistuning on flutter. It also demonstrates that when using rig test data for aeroelastic validation of CFD codes, the amount mistuning present must be known. Finally, it should be noted that the aim of this paper is the study of mistuning and not steady/unsteady validation of a CFD code and therefore minimal aerodynamic data are presented.

Analysis of Modal Parameters of Adhesively Bonded Double-Strap Joints by the Modal Strain Energy Method

1993 ◽  
Author(s):  
Mohan D. Rao ◽  
Krishna M. Gorrepati
Keyword(s):  
Strain Energy ◽  
Natural Frequencies ◽  
Structural Parameters ◽  
Flexural Vibration ◽  
Mode Shapes ◽  
Modal Parameters ◽  
Adhesively Bonded ◽  
Modal Strain Energy ◽  
Joint System ◽  
Damping Material

Abstract This paper presents the analysis of modal parameters (natural frequencies, damping ratios and mode shapes) of a simply supported beam with adhesively bonded double-strap joint by the finite-element based Modal Strain Energy (MSE) method using ANSYS 4.4A software. The results obtained by the MSE method are compared with closed form analytical solutions previously obtained by the first author for flexural vibration of the same system. Good agreement has been obtained between the two methods for both the natural frequencies and system loss factors. The effects of structural parameters and material properties of the adhesive on the modal properties of the joint system are also studied which are useful in the design of the joint system for passive vibration and noise control. In order to evaluate the MSE and analytical results, some experiments were conducted using aluminum double-strap joint with 3M ISD112 damping material. The experimental results agreed well with both analytical and MSE results indicating the validity of both analytical and MSE methods. Finally, a comparative study has been conducted using various commercially available damping materials to evaluate their relative merits for use in the design of these joints.

Split Vibration Modes in Acoustically-Coupled Disk Stacks

1995 ◽  
Author(s):  
Jung-Ge Tseng ◽  
Jonathan Wickert
Keyword(s):  
Natural Frequencies ◽  
Three Dimensional ◽  
System Level ◽  
Thin Plates ◽  
Mode Shapes ◽  
Design Parameters ◽  
Phase System ◽  
Acoustic Coupling ◽  
Annular Plates ◽  
Vibration Model

Abstract Vibration of an array of stacked annular plates, in which adjacent plates couple weakly through an acoustic layer, is investigated through experimental and theoretical methods. Such acoustic coupling manifests itself through split natural frequencies, beating in the time responses of adjacent or separated plates, and system-level modes in which plates in the array vibrate in- or out-of-phase at closely-spaced frequencies. Laboratory measurements, including a technique in which the frequency response function of all in-phase modes but no out-of-phase modes, or visa versa, is measured, demonstrate the contribution of coupling to the natural frequency spectrum, and identify the combinations of design parameters for which it is important. For the lower modes of primary interest here, the natural frequencies of the out-of-phase system modes decrease as the air layer becomes thinner, while those of the in-phase mode remain sensibly constant at the in vacuo values. A vibration model comprising N classical thin plates that couple through the three-dimensional acoustic fields established in the annular cavities between plates is developed, and its results are compared with measurements of the natural frequencies and mode shapes.

Experimental Study of Blade Vibration in Centrifugal Compressors

2011 ◽  
Author(s):  
Andrew H. Lerche ◽  
J. Jeffrey Moore ◽  
Timothy C. Allison
Keyword(s):  
High Cycle Fatigue ◽  
Axial Flow ◽  
Modal Testing ◽  
Mode Shapes ◽  
Cyclic Symmetry ◽  
Centrifugal Compressors ◽  
Compressor Blades ◽  
Blade Vibration ◽  
Phase Cancellation ◽  
Blade Failure

Blade vibration in turbomachinery is a common problem that can lead to blade failure by high cycle fatigue. Although much research has been performed on axial flow turbomachinery, little has been published for radial flow machines such as centrifugal compressors and radial inflow turbines. This work develops a test rig that measures the resonant vibration of centrifugal compressor blades. The blade vibrations are caused by the wakes coming from the inlet guide vanes. These vibrations are measured using blade mounted strain gauges during a rotating test. The total damping of the blade response from the rotating test is compared to the damping from the modal testing performed on the impeller. The mode shapes of the response and possible effects of mistuning are also discussed. The results show that mistuning can affect the phase cancellation which one would expect to see on a system with perfect cyclic symmetry.

scholarly journals Modal Sensitivity Based Sensor Placement for Damage Identification Under Sparsity Constraint

2019 ◽  
Author(s):  
Bartlomiej Blachowski
Keyword(s):  
Damage Identification ◽  
Structural Parameters ◽  
Three Dimensional ◽  
Least Square ◽  
Truss Structures ◽  
Shape Sensitivity ◽  
Damage Scenarios ◽  
Norm Minimization ◽  
Steel Members ◽  
Upper Deck

The present study deals with a comprehensive approach for damage identification of spatial truss structures. The novelty of the proposed approach consists of a three-level analysis. First, sensitivity of assumed modal characteristics is calculated. Second, natural frequency sensitivity is used to determine hardly identifiable structural parameters and mode shape sensitivity is applied to select damage-sensitive locations of sensors. Third, two sparsity constrained optimization algorithms are tested towards efficient identification of applied damage scenarios. These two algorithms are based on ℓ1-norm minimization and non-negative least square (NNLS) solution.Performances of both proposed algorithms have been compared in two realistic case studies: the first one concerned a three-dimensional truss girder with 61 structural parameters and the second one was devoted to an upper-deck arch bridge composed of 416 steel members.

Sign in / Sign up

Export Citation Format

Share Document