Numerical investigation of the axial compressor performance with inlet distortions

2017 ◽  
Vol 232 (8) ◽  
pp. 1434-1441
Author(s):  
ZX Liu ◽  
HZ Diao ◽  
XC Zhu ◽  
ZH Du
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Body Force ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Force Model ◽  
Transonic Compressor ◽  
High Pressure Ratio ◽  
Compressor Performance

In this paper, a three-dimensional body force model for predicting compressor performance and stability is implemented in the Ansys CFX. The influence of the blade rows on the flow field is represented by the source terms of CFX-solver equation. At first, a high-speed and high-pressure-ratio transonic compressor with the clean inlet is investigated. The overall performance and the flow fields are in agreement well with those of the experimental date, so the model is reliable and correct. Then, the effects of the circumferential distortions in the inlet total pressure and the total temperature on the compressor performance and flow field are also illustrated, respectively. In summary, the proposed body force model is suitable to investigate the flow field of the compressor with the inlet distortions.

Numerical research on inlet total pressure distortion in a transonic compressor with non-axisymmetric stator

2017 ◽  
Vol 233 (2) ◽  
pp. 667-678 ◽  
Author(s):  
Peng Sun ◽  
Wenguang Fu ◽  
Hong Wang ◽  
Jingjun Zhong
Keyword(s):  
Flow Field ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Deep Understanding ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Transonic Compressor ◽  
Compressor Performance ◽  
Software Pack

The adverse impacts of non-uniform inlet flow have been the focus for several decades with the increase of the operating range of engines. A deep understanding of the flow mechanism of distortion passing through a compressor is needed urgently and the improvement of the compressor performance becomes more and more important. In this paper, a non-axisymmetric stator is presented with significant non-axisymmetric characteristics in a transonic compressor to investigate compressor performance and flow field effects. A time-dependent three-dimensional Reynolds-averaged Navier-Stokes equation composed in ‘Fluent Software Pack’ is validated and used to perform the simulations. The flow fields with distorted inlet are obtained and the effects of original stator and non-axisymmetric stator in a transonic compressor are compared. The results are discussed in terms of the effects of non-axisymmetric stator on compressor performance, blockage of flow passage, rotor and stator. The results show that the non-axisymmetric stator influences not only the stator flow field but also the rotor flow field, so the efficiency and total pressure ratio are improved correspondingly.

Characteristics of Stable Rotating Stall Cells in an Axial Compressor

2017 ◽  
Author(s):  
Adam R. Hickman ◽  
Scott C. Morris
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Axial Compressor ◽  
Field Measurements ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Stable Operation ◽  
Double Phase

Flow field measurements of a high-speed axial compressor are presented during pre-stall and post-stall conditions. The paper provides an analysis of measurements from a circumferential array of unsteady shroud static pressure sensors during stall cell development. At low-speed, the stall cell approached a stable size in approximately two rotor revolutions. At higher speeds, the stall cell developed within a short amount of time after stall inception, but then fluctuated in circumferential extent as the compressor transiently approached a stable post-stall operating point. The size of the stall cell was found to be related to the annulus average flow coefficient. A discussion of Phase-Locked Average (PLA) statistics on flow field measurements during stable operation is also included. In conditions where rotating stall is present, flow field measurements can be Double Phase-Locked Averaged (DPLA) using a once-per-revolution (1/Rev) pulse and the period of the stall cell. The DPLA method provides greater detail and understanding into the structure of the stall cell. DPLA data indicated that a stalled compressor annulus can be considered to contained three main regions: over-pressurized passages, stalled passages, and recovering passages. Within the over-pressured region, rotor passages exhibited increased blade loading and pressure ratio compared to pre-stall values.

Calculation of Flow Instability Inception in High Speed Axial Compressors

2014 ◽  
Author(s):  
Xiaohua Liu ◽  
Yanpei Zhou ◽  
Xiaofeng Sun ◽  
Dakun Sun
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Body Force ◽  
Present Model ◽  
Flow Instability ◽  
Tip Clearance ◽  
Force Model ◽  
Fine Grid ◽  
Stall Margin ◽  
Onset Point

This paper applies a theoretical model developed recently to calculate the flow instability inception point in axial high speed compressors system. After the mean flow field is computed by steady CFD simulation, a body force approach, which is a function of flow field data and comprises of one inviscid part and the other viscid part, is taken to duplicate the physical sources of flow turning and loss. Further by applying appropriate boundary conditions and spectral collocation method, a group of homogeneous equations will yield from which the stability equation can be derived. The singular value decomposition method is adopted over a series of fine grid points in frequency domain, and the onset point of flow instability can be judged by the imaginary part of the resultant eigenvalue. The first assessment is to check the applicability of the present model on calculating the stall margin of one single stage transonic compressors at 85% rotational speed. The reasonable prediction accuracy validates that this model can provide an unambiguous judgment on stall inception without numerous requirements of empirical relations of loss and deviation angle. It could possibly be employed to check over-computed stall margin during the design phase of new high speed fan/compressors. The following validation case is conducted to study the nontrivial role of tip clearance in rotating stall, and a parameter study is performed to investigate the effects of end wall body force coefficient on stall onset point calculation. It is verified that the present model could qualitatively predict the reduced stall margin by assuming a simplified body force model which represents the response of a large tip clearance on the unsteady flow field.

Numerical Investigation on the Effect of Bleed Port With Self-Recirculating Casing Treatment on the Stability of a 1.5-Stage Transonic Compressor

2019 ◽  
Author(s):  
Yiming Zhong ◽  
WuLi Chu ◽  
HaoGuang Zhang
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Stability Margin ◽  
Axial Position ◽  
Stable Operation ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Efficiency

Abstract Compared to the traditional casing treatment, the self-recirculating casing treatment (SCT) can improve or not decrease the compressor efficiency while achieving the stall margin improvement. For the bleed port, the main design indicator is to reduce the flow loss caused by suction, while providing sufficient jet flow and jet pressure to the injector. In order to gain a better study of the bleed port stabilization mechanisms, the bleed configuration was parameterized with the bleed port inlet width and the bleed port axial position. Five kinds of recirculating casing treatments were applied to a 1.5-stage transonic axial compressor with the method of three-dimensional unsteady numerical simulation. Fifteen identical self-recirculating devices are uniformly mounted around the annulus. The numerical results show that the SCT can improve compressor total pressure ratio and stability, shift the stall margin towards lower mass flows. Furthermore, it has no impact on compressor efficiency. The optimal case presents that stability margin is improved by 6.7% employing 3.1% of the annulus mass flow. Expanding bleed port inlet width to an intermediate level can further enhance compressor stability, but excessive bleed port inlet width will reduce the stabilization effect. The optimal bleed port position is located in the blocked area of the low energy group at the top of the rotor. In the case of solid casing, stall inception was the tip blockage, which was mainly triggered by the interaction of the tip leakage vortex and passage shock. From radial distribution, the casing treatment predominantly affects the above 70% span. The reduction of tip reflux region by suction effect is the main reason for the extension of stable operation range. The SCT also has an obvious stability improvement in tip blockage stall, while delaying the occurrence of compressor stall.

Experimental Investigation of Aspiration in a Multi-Stage High-Speed Axial-Compressor

2016 ◽  
Author(s):  
Jan Siemann ◽  
Ingolf Krenz ◽  
Joerg R. Seume
Keyword(s):  
Flow Field ◽  
Total Pressure ◽  
High Speed ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Reference Configuration ◽  
Corner Separation ◽  
Part Load ◽  
Total Pressure Ratio ◽  
Isentropic Efficiency

Reducing the fuel consumption is a main objective in the development of modern aircraft engines. Focusing on aircraft for mid-range flight distances, a significant potential to increase the engines overall efficiency at off-design conditions exists in reducing secondary flow losses of the compressor. For this purpose, Active Flow Control (AFC) by aspiration or injection of fluid at near wall regions is a promising approach. To experimentally investigate the aerodynamic benefits of AFC by aspiration, a 4½-stage high-speed axial-compressor at the Leibniz Universitaet Hannover was equipped with one AFC stator row. The numerical design of the AFC-stator showed significant hub corner separations in the first and second stator for the reference configuration at the 80% part-load speed-line near stall. Through the application of aspiration at the first stator, the numerical simulations predict the complete suppression of the corner separation not only in the first, but also in the second stator. This leads to a relative increase in overall isentropic efficiency of 1.47% and in overall total pressure ratio of 4.16% compared to the reference configuration. To put aspiration into practice, the high-speed axial-compressor was then equipped with a secondary air system and the AFC stator row in the first stage. All experiments with AFC were performed for a relative aspiration mass flow of less than 0.5% of the main flow. Besides the part-load speed-lines of 55% and 80%, the flow field downstream of each blade row was measured at the AFC design point. Experimental results are in good agreement with the numerical predictions. The use of AFC leads to an increase in operating range at the 55% part-load speed-line of at least 19%, whereas at the 80% part-load speed-line no extension of operating range occurs. Both speed-lines, however, do show a gain in total pressure ratio and isentropic efficiency for the AFC configuration compared to the reference configuration. Compared to the AFC design point, the isentropic efficiency ηis rises by 1.45%, whereas the total pressure ratio Πtot increases by 1.47%. The analysis of local flow field data shows that the hub corner separation in the first stator is reduced by aspiration, whereas in the second stator the hub corner separation slightly increases. The application of AFC in the first stage further changes the stage loading in all downstream stages. While the first and third stage become unloaded by application of AFC, the loading in terms of the De-Haller number increases in the second and especially in the fourth stage. Furthermore, in the reference as well as in the AFC configuration, the fourth stator performs significantly better than predicted by numerical results.

A Method of Stall and Surge Prediction in Axial Compressors Based On Three-Dimensional Body-Force Model

2021 ◽  
Author(s):  
Hanxuan Zeng ◽  
Xinqian Zheng ◽  
Mehdi Vahdati
Keyword(s):  
Body Force ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Rotating Stall ◽  
The Body ◽  
Force Model ◽  
Computational Domain ◽  
Forward Flow ◽  
Axial Compressors

Abstract The occurrence of stall and surge in axial compressors has a great impact on the performance and reliability of aero-engines. Accurate and efficient prediction of the key features during these events has long been the focus of engine design processes. In this paper, a new body-force model that can capture the three-dimensional and unsteady features of stall and surge in compressors at a fraction of time required for URANS computations is proposed. To predict the rotating stall characteristics, the deviation of local airflow angle from the blade surface is calculated locally during the simulation. According to this local deviation, the computational domain is divided into stalled and forward flow regions, and the body-force field is updated accordingly; to predict the surge characteristics, the local airflow direction is used to divide the computational domain into reverse flow regions and forward flow regions. A single-stage axial compressor and a three-stage axial compressor are used to verify the proposed model. The results show that the method is capable of capturing stall and surge characteristics correctly. Compared to the traditional fully three-dimensional URANS method (fRANS), the simulation time for multi-stage axial compressors is reduced by 1 to 2 orders of magnitude.

An Investigation of the Effect of Cascade Area Ratios on Transonic Compressor Performance

1994 ◽  
Author(s):  
A. R. Wadia ◽  
W. W. Copenhaver
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Area Ratio ◽  
Peak Efficiency ◽  
Trailing Edge ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Boundary Layer Interaction ◽  
Compressor Performance

Transonic compressor rotor performance is highly sensitive to variations in cascade area ratios. This paper reports on the design, experimental evaluation and three-dimensional viscous analysis of four low aspect ratio transonic rotors that demonstrate the effects of cascade throat area, internal contraction and trailing edge effective camber on compressor performance. The cascade throat area study revealed that tight throat margins result in increased high speed efficiency with lower part speed performance. Stall line was also improved slightly over a wide range of speeds with a lower throat-to-upstream capture area ratio. Higher internal contraction, expressed as throat-to-mouth area ratio, also results in increased design point peak efficiency, but again costs performance at the lower speeds. Reducing the trailing edge effective camber expressed as throat-to-exit area ratio, results in an improvement in peak efficiency level without significantly lowering the stall line. Among all four rotors, the best high speed efficiency was obtained by the rotor with tight throat margin and highest internal contraction, but its efficiency was the lowest at part speed. The best compromise between high speed and part speed efficiency was achieved by the rotor with a large throat and a lower trailing edge effective camber. The differences in the shock structure and the shock boundary layer interaction of the four blades was analyzed using a three-dimensional viscous code. The analytical results are used to supplement the data and provide further insight into the detailed physics of the flow field.

Aerodynamic Design and Analysis of a High Pressure Ratio Aspirated Compressor Stage

2000 ◽  
Author(s):  
Ali A. Merchant ◽  
Mark Drela ◽  
Jack L. Kerrebrock ◽  
John J. Adamczyk ◽  
Mark Celestina
Keyword(s):  
Boundary Layer ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Adverse Pressure Gradient ◽  
Compressor Stage ◽  
High Pressure Ratio ◽  
Total Pressure Ratio ◽  
Isentropic Efficiency

The pressure ratio of axial compressor stages can be significantly increased by controlling the development of blade and endwall boundary layers in regions of adverse pressure gradient by means of boundary layer suction. This concept is validated and demonstrated through the design and analysis of a unique aspirated compressor stage which achieves a total pressure ratio of 3.5 at a tip speed of 1500 ft/s. The aspirated stage was designed using an axisymmetric through-flow code coupled with a quasi three-dimensional cascade plane code with inverse design capability. Validation of the completed design was carried out with three-dimensional Navier-Stokes calculations. Spanwise slots were used on the rotor and stator suction surfaces to bleed the boundary layer with a total suction requirement of 4% of the inlet mass flow. Additional bleed of 3% was also required on the hub and shroud near shock impingement locations. A three-dimensional viscous evaluation of the design showed good agreement with the quasi three-dimensional design intent, except in the endwall regions. The three-dimensional viscous analysis predicted a mass averaged total pressure ratio of 3.7 at an isentropic efficiency of 93% for the rotor, and a mass averaged total pressure ratio of 3.4 at an isentropic efficiency of 86% for the stage.

Computation of the Flow Field of Transonic Axial Compressor by Steady Arbitrary Lagrangian Eulerian Formulation

2008 ◽  
Author(s):  
Adel Ghenaiet ◽  
Nouredine Djeghri
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Arbitrary Lagrangian Eulerian ◽  
Viscous Effects ◽  
Stability Range ◽  
Transonic Compressor ◽  
Ale Formulation ◽  
Transonic Axial Compressor ◽  
Residual Smoothing

This paper presents a multi-block solver dealing with an inviscid three dimensional compressible flow through a transonic compressor blading. For efficient computations of the 3D time dependant Euler equations, this solver that we have developed has been cast within a stationary ALE ‘Arbitrary Lagrangian Eulerian’. The main contribution of this paper is by consolidating this ALE formulation, to alleviate the shortcomings linked to rotation effects and the mixed relative subsonic–supersonic inlet flow conditions, which are now simply implemented through an absolute subsonic flow velocity. The finite volume based solver is using the central differencing scheme known as JST (Jameson-Schmidt-Turkel). The explicit multistage Runge-Kutta algorithm is used as a pseudo time marching to the steady-state, coupled with two convergence accelerating techniques; the variable local time-stepping and the implicit residual smoothing procedure. The adaptive implicit residual smoothing has extended the stability range of this explicit scheme, and proved to be successful in accelerating the rate of convergence. This code is currently being extended to include viscous effects, where fluxes are discretized based on Green’s theorem. To support this solver, an H type grid generator based on algebraic and elliptic methods has been developed. The segmentation of the complete domain into smaller blocks has provided full topological and geometrical flexibilities. The code was used to compute the flow field of a transonic axial compressor NASA rotor 37, and comparisons between the calculations and some available experimental data under the design speed and part speed, show qualitatively good agreement.

Meanline Modeling of a Radial-Inflow Turbine Nozzle With Supersonic Expansion

2016 ◽  
Author(s):  
Shuo Li ◽  
Eric M. Krivitzky ◽  
Xuwen Qiu
Keyword(s):  
Flow Field ◽  
Cfd Simulation ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Expansion Ratio ◽  
Accurate Estimation ◽  
Nozzle Outlet ◽  
Supersonic Expansion ◽  
High Pressure Ratio ◽  
Flow Deviation

High pressure ratio, radial-inflow turbines typically experience supersonic expansion in the nozzle section. Accurate estimation of the flow conditions and velocity triangle at the nozzle outlet is of critical importance in correctly predicting the overall turbine performance. The meanline modeling of such a nozzle requires special attention, due to the significantly altered flow field downstream of the throat. In this study, the flow field of a supersonic expansion nozzle is investigated, using a three-dimensional (3D) computational fluid dynamics (CFD) simulation calibrated with test data. Three different CFD configurations are explored: the nozzle alone, the nozzle plus rotor coupled with a mixing plane, and the nozzle plus rotor coupled with the nonlinear harmonic (NLH) method. These configurations are compared to each other to gauge the effect of the rotor and stator interaction and the potential for error in establishing the velocity triangles. The exit vane angle, number of vanes, and expansion ratio across the nozzle are systematically varied to provide the data as the base for nozzle modeling. Finally, a meanline method is proposed to calculate the pressure loss and flow deviation at the nozzle outlet and is compared with CFD results.

Sign in / Sign up

Export Citation Format

Share Document