Pineapple shell fiber as reinforcement in cassava starch foam trays

2019 ◽  
Vol 27 (8) ◽  
pp. 496-506
Author(s):  
Arnold Cabanillas ◽  
Julio Nuñez ◽  
JP Cruz-Tirado ◽  
R Vejarano ◽  
Delia R Tapia-Blácido ◽  
...  
Keyword(s):  
Food Packaging ◽  
Physical And Mechanical Properties ◽  
Crystallinity Index ◽  
High Water ◽  
Cassava Starch ◽  
Absorption Capacity ◽  
Expanded Polystyrene ◽  
Molding Process ◽  
Dry Food ◽  
Physicochemical And Structural Properties

Pineapple shell, considered a waste in the juice industry, was used as a reinforcement material to produce biodegradable foam trays (FTs) based on cassava starch by a compression molding process. These foams were prepared with different starch/fiber ratios and then were characterized according to their microstructure and physical and mechanical properties. The starch/fiber ratio of 95/5 showed the lowest values of thickness and density (2.58 mm and 367 kg m−3, respectively). There was a good distribution of the pineapple shell fiber throughout the polymeric matrix. All FTs showed a semicrystalline structure and 95/5 ratio showed the highest crystallinity index (CI) value (39%). In addition, this ratio improved the tensile strength of the FTs, obtaining similar values to expanded polystyrene (EPS) samples, used as the reference material. Nevertheless, all FTs reinforced with pineapple shell fiber showed high water absorption capacity (WAC); therefore, future studies should focus on to improve the physicochemical and structural properties of the cassava starch-based foams, considering the promising potential of this novel biodegradable material for dry food packaging, such as a viable alternative to reduce the use of petroleum-based materials such as commercial EPS trays.

scholarly journals Recent Developments in Seafood Packaging Technologies

Foods ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 940
Author(s):  
Michael G. Kontominas ◽  
Anastasia V. Badeka ◽  
Ioanna S. Kosma ◽  
Cosmas I. Nathanailides
Keyword(s):  
Shelf Life ◽  
Food Packaging ◽  
Modified Atmosphere Packaging ◽  
High Water ◽  
Edible Films ◽  
Nitrogenous Compounds ◽  
Quality Properties ◽  
Unsaturated Lipids ◽  
Active Food Packaging ◽  
Seafood Products

Seafood products are highly perishable, owing to their high water activity, close to neutral pH, and high content of unsaturated lipids and non-protein nitrogenous compounds. Thus, such products require immediate processing and/or packaging to retain their safety and quality. At the same time, consumers prefer fresh, minimally processed seafood products that maintain their initial quality properties. The present article aims to review the literature over the past decade on: (i) innovative, individual packaging technologies applied to extend the shelf life of fish and fishery products, (ii) the most common combinations of the above technologies applied as multiple hurdles to maximize the shelf life of seafood products, and (iii) the respective food packaging legislation. Packaging technologies covered include: Modified atmosphere packaging; vacuum packaging; vacuum skin packaging; active food packaging, including oxygen scavengers; carbon dioxide emitters; moisture regulators; antioxidant and antimicrobial packaging; intelligent packaging, including freshness indicators; time–temperature indicators and leakage indicators; retort pouch processing and edible films; coatings/biodegradable packaging, used individually or in combination for maximum preservation potential.

scholarly journals Cellulose Nanofibrils/Xyloglucan Bio-Based Aerogels with Shape Recovery

Gels ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 5
Author(s):  
Samuel Mandin ◽  
Samuel Moreau ◽  
Malika Talantikite ◽  
Bruno Novalès ◽  
Jean-Eudes Maigret ◽  
...  
Keyword(s):  
Water Absorption ◽  
Shape Recovery ◽  
Cellulose Nanofibrils ◽  
High Water ◽  
Absorption Capacity ◽  
Absorption Properties ◽  
High Affinity ◽  
High Water Absorption ◽  
Freezing Procedure ◽  
The Impact

Bio-based aerogels containing cellulose nanofibrils (CNFs) are promising materials due to the inherent physical properties of CNF. The high affinity of cellulose to plant hemicelluloses (xyloglucan, xylan, pectin) is also an opportunity to develop biomaterials with new properties. Here, we prepared aerogels from gelled dispersions of CNFs and xyloglucan (XG) at different ratios by using a freeze-casting procedure in unidirectional (UD) and non-directional (ND) manners. As showed by rheology analysis, CNF and CNF/XG dispersions behave as true gels. We investigated the impact of the freezing procedure and the gel’s composition on the microstructure and the water absorption properties. The introduction of XG greatly affects the microstructure of the aerogel from lamellar to cellular morphology. Bio-based aerogels showed high water absorption capacity with shape recovery after compression. The relation between morphology and aerogel compositions is discussed.

Preparation and characterization of biodegradable cassava starch thin films for potential food packaging applications

Cellulose ◽  
2021 ◽  
Author(s):  
Sumedha M. Amaraweera ◽  
Chamila Gunathilake ◽  
Oneesha H. P. Gunawardene ◽  
Nimasha M. L. Fernando ◽  
Drashana B. Wanninayaka ◽  
...  
Keyword(s):  
Thin Films ◽  
Food Packaging ◽  
Cassava Starch ◽  
Potential Food

Comparison of Bio and Eco-technologies with Chemical Methods for Pre-treatment of Flax Fibers: Impact on Fiber Properties

2014 ◽  
Vol 9 (4) ◽  
pp. 155892501400900 ◽  
Author(s):  
Sabela Camano ◽  
Nemeshwaree Behary ◽  
Philippe Vroman ◽  
Christine Campagne
Keyword(s):  
Water Absorption ◽  
Fiber Bundle ◽  
Glass Fibers ◽  
Fiber Surface ◽  
Pectate Lyase ◽  
High Water ◽  
Absorption Capacity ◽  
Water Absorption Capacity ◽  
Flax Fibers ◽  
The Impact

Flax fibers, available as fiber bundles, are commonly used as fiber reinforcement in composite materials as a substitute for glass fibers. Pre-treatments are often necessary for improving fiber-resin adhesion, and also to facilitate fiber elementarization, and to improve fiber ability to be implemented in mechanical processes limiting fiber damages. This paper focuses on the impact of biotechnologies (effect of 2 different enzymes: a pectate lyase and a laccase) and of an ecotechnology (ultrasound with ethanol), compared to classical chemical pre-treatments (using aqueous NaOH and ammonia) on the final flax fiber bundle properties, before and after a carding process. Fiber surface properties (wettability and/or zeta potential values), fiber elementarization and mechanical properties vary with the type of treatment (chemical nature of product and conditions used). Fibers elementarised using pectate lyase and ultrasound/ethanol have a hydrophilic surface and a high water absorption capacity, and are also of highest quality in terms of increased fineness. Treatment with NaOH yields the poorest fiber bundle tenacity. Laccase enzyme yields long thick hydrophobic fibers having very low water absorption capacity, and the most neutral surface charge. Properties of flax fibers can be easily monitored using different pre-treatments resulting in fibers which would be suited for various final applications.

scholarly journals Resistance of ETICS with Fire Barriers to Cyclic Hygrothermal Impact

2021 ◽  
Vol 13 (16) ◽  
pp. 9220
Author(s):  
Rosita Norvaišienė ◽  
Paweł Krause ◽  
Vincent Buhagiar ◽  
Arūnas Burlingis
Keyword(s):  
Physical And Mechanical Properties ◽  
Mineral Wool ◽  
Expanded Polystyrene ◽  
Test Rig ◽  
Horizontal Strip ◽  
Climate Chamber ◽  
Expanded Polystyrene Foam ◽  
Hygrothermal Performance ◽  
Thermal Data ◽  
Chamber Temperature

The article presents the results of a set of hygrothermal experiments of an external wall insulated with an ETICS. As an add-on to previous studies, thermal insulation in the form of polystyrene with an additional horizontal strip of mineral wool was used. Laboratory tests were carried out in accordance with ETAG 004. The ETICS test rig was composed of combustible expanded polystyrene foam (EPS) and horizontal strips of noncombustible mineral wool (MW) fire barriers over windows. The physical and mechanical properties of four types of finishing renders (without an additional reinforcement mesh in base coat of the fire barriers) were analyzed across full hygrothermal cycles in a climate chamber. Temperature sensors were mounted onto different ETICS layers to collect thermal data during the weathering. The testing of ETICS regarding their hygrothermal performance revealed that there were no visible defects on any renderings and over the junctions depending on the type of used insulation materials. Results also showed that the joints of EPS and MW have approximately half of their bond strength from polystyrene strength.

scholarly journals Structural Use of Expanded Polystyrene Concrete

2020 ◽  
Vol 5 (6) ◽  
pp. 1131-1138
Author(s):  
Adeniran Jolaade ADEALA ◽  
Olugbenga Babajide SOYEM
Keyword(s):  
Environmental Pollution ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Consumer Products ◽  
Expanded Polystyrene ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Construction Companies ◽  
Fine Aggregates ◽  
Concrete Matrix

Expanded polystyrene (EPS) wastes are generated from industries and post-consumer products. They are non-biodegradable but are usually disposed by burning or landfilling leading to environmental pollution. The possibility of using EPS as partial replacement for fine aggregates in concrete has generated research interests in recent times. However, since the physical and mechanical properties of EPS are not like those of conventional fine aggregates, this study is focussed on the use of EPS as an additive in concrete while keeping other composition (sand and granite) constant. Expanded polystyrene was milled, the bulk density of EPS was 10.57kg/m3 and particle size distributions were determined. Engineering properties of expanded polystyrene concrete were determined in accordance with BS 8110-2:1985. The result showed that the amount of expanded polystyrene incorporated in concrete influence the properties of hardened and fresh concrete. The compressive strengths of 17.07MPa with 5 % expanded polystyrene concrete at 28 days for example can be used as a lightweight concrete for partitioning in offices. Incorporating expanded polystyrene granules in a concrete matrix can produce lightweight polystyrene aggregate concrete of various densities, compressive strengths, flexural strengths and tensile strengths. In conclusion, this reduces environmental pollution, reduction in valuable landfill space and also for sustainability in construction companies

scholarly journals OPTIMUM PERFORMANCE OF STABILIZED EDE LATERITE AS AN ALTERNATIVE CONSTRUCTION MATERIAL

2020 ◽  
Vol 3 (8) ◽  
pp. 1-8
Author(s):  
Adegbenle Bukunmi O
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Construction Material ◽  
High Water ◽  
Good Alternative ◽  
Linear Shrinkage ◽  
Absorption Capacity ◽  
Water Absorption Capacity ◽  
Optimum Performance ◽  
High Water Absorption

Laterite samples from Ede area with particle components of 19.7% clay, 32.8% silt and 47.5% sand was stabilized with combined cement, lime and bitumen and test for Compressive strength, Linear Shrinkage, Permeability and Water Absorption. The stabilizers were mixed with laterite soil in different ratios and percentage. The laterite carried 90% which is constant while the three stabilizers shared the remaining 10% in varying form. After 28 days of curing, laterite stabilizer with 90% of laterite, 8% of cement, 1% lime and 1% bitumen (LCLB1) possessed compressive strength of 2.01N/mm2. It Water Absorption Capacity was 3.05%. LCLB4 stabilizer (90% laterite, 6% cement, 2% lime and 2% bitumen) has the same compressive strength with LCLB1 stabilizer but with a high Water Absorption Capacity of 4.2%. The stabilizer of 90% laterite, 3.33% cement, 3.33% lime and 3.33% of bitumen (LCLB8) has the lowest compressive strength of 0.74N/mm2 and the highest Water Absorption Capacity of 5.39%. The results shows that LCLB1 stabilizer is a better stabilizer for strength and blocks made from laterite stabilized with it stand a good alternative to sand Crete blocks in building constructions. The combination of these stabilizers in order to determine a most economical volume combination for optimum performance is highly possible and economical.

The Behavior of FRA Concrete with High Replacement Ratio

2018 ◽  
Vol 760 ◽  
pp. 204-209 ◽  
Author(s):  
Magdaléna Šefflová
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Absorption Capacity ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Replacement Ratio ◽  
Natural Sand ◽  
Concrete Mixtures

This study deals with determination of the properties of the fine recycled aggregate (FRA) concrete with partial replacement of natural sand in concrete mixtures. The FRA was obtained from concrete waste and crushed on fraction 0 – 4 mm by laboratory jaw crusher. The geometrical and physical properties of natural sand and the FRA were tested. The main goal of this study is evaluation of the basic physical and mechanical properties of the concrete with partial natural sand replacement by the FRA such as workability, water absorption capacity, compressive strength and flexural strength. A total four concrete mixtures were prepared. The first concrete mixture was prepared only with natural sand, did not include the FRA. In other concrete mixtures, natural sand was replaced by the FRA in various replacement ratios (40 %, 50 %, and 60 %). All concrete mixtures were designated with the same parameters for clear comparison. The workability of fresh concrete mixtures and physical and mechanical properties of hardened concrete were tested.

Powder Injection Molding of Ti-6Al-4V Alloy for Defect-Free High Performance Titanium Parts with Low Carbon/Oxygen Contents

2018 ◽  
Vol 770 ◽  
pp. 189-194
Author(s):  
Dong Guo Lin ◽  
Jae Man Park ◽  
Tae Gon Kang ◽  
Seong Taek Chung ◽  
Young Sam Kwon ◽  
...  
Keyword(s):  
Injection Molding ◽  
Alloy Powder ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Powder Injection Molding ◽  
Powder Injection ◽  
Solid Loading ◽  
Injection Molding Process ◽  
Low Carbon ◽  
Molding Process

In this work, powder injection molding (PIM) of Ti-6Al-4V alloy powder has been studied. Defect-free high performance Ti-6Al-4V parts with low carbon/oxygen contents have been successfully prepared by PIM. A pre-alloyed Ti-6Al-4V alloy powder and wax-polymer binder system have been mixed together to prepare the feedstock. In mixing stage, the solid loading percentage and mixing conditions have been optimized. Rheological and thermal debinding behaviors of prepared feedstock have been characterized and numerically expressed based on rheometry and thermal gravity experimental results. In addition, the injection molding process of Ti-6Al-4V parts has been numerically analyzed to optimize the injection molding conditions. Consequently, the defect-free Ti-6Al-4V parts with low carbon and oxygen contents have been successfully fabricated by PIM, which exhibits excellent physical and mechanical properties.

Lightweight Cellular Glass Composite from Eggshell and Glass Cullet Powder for Insulation and Bioactive Glass Applications

2020 ◽  
Vol 858 ◽  
pp. 151-156
Author(s):  
Nuchnapa Tangboriboon ◽  
Nathawith Ratchatawatanapipat ◽  
Kunanya Kongpaopong
Keyword(s):  
Thermal Expansion ◽  
Water Absorption ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Flat Glass ◽  
High Water ◽  
Glass Cullet ◽  
Molding Process ◽  
Glass Composites ◽  
Cellular Glass

Cellular glass composites can be made of waste flat glass or bottle glass added with eggshell powder 0, 1, 3 and 5%wt and then fired at 800° and 900°C for 1 h using compression molding process. Adding eggshell powder mixed with glass cullet affects to form open and closed pores and to decrease firing temperature, thermal expansion coefficient and light weight. However, adding high amount of eggshell powder affects to form an excessively amount of open and closed pores effect to increase water absorption. The standard Thailand Industries determines water absorption of glass foam less than 25% because high water absorption affects to decrease mechanical properties. Therefore, cellular glass composites added 1, 3 and 5%wt should not be fired at temperature higher than 800°C for 1h. In addition, the cellular glass composites added 1 %wt eggshell powder and fired at 900°C for 1 h still have low water absorption and low thermal expansion coefficient. Cellular glass composites are potential to apply for many industries such as construction, petroleum and petrochemical, insulation, medical and dental applications.

Sign in / Sign up

Export Citation Format

Share Document