Numerical research on a vortex shedding induced piezoelectric-electromagnetic energy harvester

2021 ◽  
pp. 1045389X2110116
Author(s):  
Xia Li ◽  
Zhiyuan Li ◽  
Benxue Liu ◽  
Jun Zhang ◽  
Weidong Zhu
Keyword(s):  
Wind Speed ◽  
Output Power ◽  
Vortex Shedding ◽  
Energy Harvester ◽  
Hybrid Structure ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Speed Range ◽  
Electromechanical Coupled

To widen the operation wind speed bandwidth of a classic vortex shedding induced vibration piezoelectric energy harvester, a piezoelectric-electromagnetic hybrid energy harvester based on vortex shedding induced vibration is designed. The hybrid vortex shedding induced vibration energy harvester (HVSIVEH) includes a vortex shedding induced vibration piezoelectric energy harvester (VSIVPEH) and an electromagnetic vibration energy harvester (EVEH). The electromechanical coupled vibration model of the hybrid structure was established. By comparing the variations of the output power as a function of the wind speed of the HVSIVEH and the classic VSIVPEH, it is found that the power response curve of the HVSIVEH has two peaks. The hybrid structure can broaden the working wind speed range. The lower the requirement on the output power level, the more obvious the effect of widening the wind speed range. By the solution and analysis of the electromechanical coupled model, better values of related parameters of the HVSIVEH are obtained. The first and second peaks of the output power of the HVSIVEH show better values of 1.9 and 2.2 mW, respectively, under these parameters.

scholarly journals Optimization of Galloping Piezoelectric Energy Harvester with V-Shaped Groove in Low Wind Speed

Energies ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4619 ◽  
Author(s):  
Kaiyuan Zhao ◽  
Qichang Zhang ◽  
Wei Wang
Keyword(s):  
Wind Speed ◽  
Output Power ◽  
Critical Velocity ◽  
Energy Harvester ◽  
Windward Side ◽  
Flow Induced Vibration ◽  
Vibration Energy Harvester ◽  
Low Wind Speed ◽  
Local Hopf Bifurcation ◽  
Piezoelectric Energy

A square cylinder with a V-shaped groove on the windward side in the piezoelectric cantilever flow-induced vibration energy harvester (FIVEH) is presented to improve the output power of the energy harvester and reduce the critical velocity of the system, aiming at the self-powered supply of low energy consumption devices in the natural environment with low wind speed. Seven groups of galloping piezoelectric energy harvesters (GPEHs) were designed and tested in a wind tunnel by gradually changing the angle of two symmetrical sharp angles of the V-groove. The GPEH with a sharp angle of 45° was selected as the optimal energy harvester. Its output power was 61% more than the GPEH without the V-shaped groove. The more accurate mathematical model was made by using the sparse identification method to calculate the empirical parameters of fluid based on the experimental data and the theoretical model. The critical velocity of the galloping system was calculated by analyzing the local Hopf bifurcation of the model. The minimum critical velocity was 2.53 m/s smaller than the maximum critical velocity at 4.69 m/s. These results make the GPEH with a V-shaped groove (GPEH-V) more suitable to harvest wind energy efficiently in a low wind speed environment.

Theoretical modeling and analysis of a 2-degree-of-freedom hybrid piezoelectric–electromagnetic vibration energy harvester with a driven beam

2018 ◽  
Vol 29 (11) ◽  
pp. 2465-2476 ◽  
Author(s):  
Dan Zhao ◽  
Shaogang Liu ◽  
Qingtao Xu ◽  
Wenyi Sun ◽  
Tao Wang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Energy Harvester ◽  
Degree Of Freedom ◽  
Energy Output ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Electromagnetic Vibration ◽  
Operating Bandwidth

In the article, a novel 2-degree-of-freedom hybrid piecewise-linear piezoelectric–electromagnetic vibration energy harvester is presented to achieve better energy harvesting efficiency. The harvester consists of a primary piezoelectric energy harvesting device to which an electromagnetic mechanism is coupled to improve the integral energy output, and a driven beam is mounted to broaden the operating bandwidth by inducing nonlinearity. Considering the piezoelectric–electromagnetic coupling characteristics and the nonlinear factors, dynamic equations of the system are established. Expressions of the output power are deduced though averaging method. Characteristic parameters are analyzed theoretically, including the piezoelectric parameters, electromagnetic parameters, and the piecewise-linearity. Frequency sweep excitation test is conducted on the setup at an excitation acceleration of 0.3 g and results demonstrate that two resonant regions are obtained with the peak output power of 5.4 and 6.49 mW, respectively, and the operating bandwidth is increased by 8 Hz. Moreover, though adjusting the stiffness of the driven beam k3 and the gap between the primary beam and the driven beam d, the performance of the harvester can be further optimized.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

Closed-form solutions of bending-torsion coupled forced vibrations of a piezoelectric energy harvester under a fluid vortex

2021 ◽  
pp. 1-31
Author(s):  
Xiang Zhao ◽  
Weidong Zhu ◽  
Ying-hui Li
Keyword(s):  
Closed Form ◽  
Torsional Vibration ◽  
Energy Harvester ◽  
High Energy ◽  
Forced Vibrations ◽  
Vibration Energy ◽  
Beam Model ◽  
Vibration Energy Harvester ◽  
Closed Form Solutions ◽  
Piezoelectric Energy

Abstract Vibration energy harvesting problems have strongly developed in recent years. However, many researchers just consider bending vibration models of energy harvesters. As a matter of fact, torsional vibration is also important and cannot be ignored in many cases. In this work, closed-form solutions of bending-torsion coupled forced vibrations of a piezoelectric energy harvester subjected to a fluid vortex are derived. Timoshenko beam model is used for modeling the energy harvester, and the extended Hamilton's principle is used in the modeling process. Since piezoelectric effects in both bending and torsional directions are considered, two kinds of electric coupling effects appear in forced vibration equations, and a new model for the electric circuit equation is developed. Lamb-Oseen vortex model is considered in this study. Both the external aerodynamic force and moment are simple harmonic loads. Three damping coefficients are considered in the present model. Based on Green's function method, closed-form solutions of the piezoelectric energy harvester subjected to the water vortex are derived. Some published results are used to verify the present solutions. It can be concluded through analysis that when torsional vibration is considered, the bandwidth of the high energy area of the voltage becomes large, and the bending-torsion coupled vibration energy harvester can produce more power than a transverse vibration energy harvester.

scholarly journals Theoretical and Experimental Study of Nonlinear and Electro-Magneto-Mechanical-Based Piezoelectric Vibration Energy Harvester

2019 ◽  
Vol 2019 ◽  
pp. 1-17
Author(s):  
Shilong Sun ◽  
Xiao Zhang
Keyword(s):  
Experimental Study ◽  
Energy Harvester ◽  
Time History ◽  
Vibration Energy ◽  
Voltage Response ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Voltage Output ◽  
Cantilevered Beam ◽  
Substrate Plate

This paper presents a folded nonlinear electro-magneto-mechanical (EMM) vibration-based piezoelectric energy harvester system, which is built on the cantilevered beam structure and consists of one host beam and two substrate plates. The performance of the linearity and nonlinearity to the proposed EMM system is evaluated and compared. Moreover, the voltage response in time history and the phase portrait are studied under an external rectifier circuit with a resistor. The results show that the nonlinearity of the reported EMM system changes the coherent resonance vibration mode from single to double under a harmonic base excitation within the frequency range of 20 Hz–50 Hz. Meanwhile, the substrate plate D contributes more averaged voltage output at a lower frequency while the substrate plate A contributes the voltage output at the relatively higher frequency for the nonlinear EMM system. The experimental study indicates that the proposed nonlinear EMM vibration-based piezoelectric energy harvester can yield a total voltage of 8.133 [email protected] Hz while the baseline structure only produces 1.724 [email protected] Hz. In addition, the bandwidth range of high-power output is enlarged by the nonlinear EMM system, which makes this device more flexible and applicable to absorb the wasted vibration energy generated by industrial machines and public facilities.

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

scholarly journals Experiments and Electromechanical Properties of a Broadband Piezoelectric Vibration Energy Harvester

2016 ◽  
Vol 2016 ◽  
pp. 1-14
Author(s):  
Guangqing Wang ◽  
Shuaishuai Gao ◽  
Xiaojun Li
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Short Circuit ◽  
Open Circuit ◽  
Vibration Energy Harvester ◽  
Frequency Space ◽  
Piezoelectric Energy ◽  
Lumped Parameter ◽  
Maximal Output ◽  
Two Peaks

A broadband piezoelectric energy harvester (BPEH), consisting of a conventional linear piezoelectric energy harvester (CPEH) and an elastic magnifier, was presented in this paper. The improved two-degree-of-freedom lumped-parameter electromechanical model of the BPEH was established and the optimal external resistances under short-circuit and open-circuit resonance conditions were investigated to maximize the output power of the BPEH. The output voltage and output power of the BPEH obtained from the theoretical model were verified and found to be in reasonable agreement with the experimental results. The obtained results have shown that the maximal output powers under short-circuit and open-circuit resonance conditions are both 24 times that generated by the CPEH without elastic magnifier. The frequency space between the two peaks of the frequency-response curve of the BPEH is 14 Hz which is 7 times that of CPEH.

Energy Harvesting Performance of Vertically Staggered Rectangle-Through-Holes Cantilevered in Piezoelectric Vibration Energy Harvester

2019 ◽  
Author(s):  
Shan Gao ◽  
Hongrui Ao ◽  
Hongyuan Jiang
Keyword(s):  
Energy Harvesting ◽  
Integrated Circuits ◽  
Resonant Frequency ◽  
High Power ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Piezoelectric Vibration

Abstract Piezoelectric vibration energy harvesting technology has attracted significant attention for its applications in integrated circuits, microelectronic devices and wireless sensors due to high power density, easy integration, simple configuration and other outstanding features. Among piezoelectric vibration energy harvesting structures, cantilevered beam is one of the simplest and most commonly used structures. In this work, a vertically staggered rectangle-through-holes (VS-RTH) cantilevered model of mesoscale piezoelectric energy harvester is proposed, which focuses on the multi-directional vibration collection and low resonant frequency. To verify the output performances of the device, this paper employs basic materials and fabrication methods with mathematical modeling. The simulations are conducted through finite element methods to discuss the properties of VS-RTH energy harvester on resonant frequency and output characteristics. Besides, an energy storage circuit with high power collection rate is adopted as collection system. This harvester is beneficial to the further application of devices working with continuous vibrations and low power requirements.

Sign in / Sign up

Export Citation Format

Share Document