Talonavicular Joint Surface Anatomy and Prototype Resurfacing Prostheses

Foot & Ankle ◽  
1981 ◽  
Vol 2 (1) ◽  
pp. 5-14 ◽  
Author(s):  
A. U. Daniels ◽  
K. M. Samuelson ◽  
K. A. Rusin
Keyword(s):  
Range Of Motion ◽  
Surface Area ◽  
Experimental Studies ◽  
Joint Surface ◽  
Design Parameters ◽  
Radius Of Curvature ◽  
Arc Length ◽  
Human Foot ◽  
Surface Anatomy ◽  
Prosthetic Joint

The curvature and extent of a joint surface largely determine the type and range of motion possible. The talonavicular surface anatomy of 10 human foot specimens has been determined quantitatively, and the data have been compared with the design parameters for a prototype prosthetic joint. It was found that, in general, the natural talus as compared with the navicular was slightly larger in surface area and in mean arc length, but slightly smaller in mean radius of curvature. The arc length of the joint was found to be generally slightly longer along an axis positioned from slightly medial of dorsal to slightly lateral of ventral. In contrast, no general orientation of the radius of curvature was observed. Also, it was found that the congruency between the talus and navicular surfaces, as indicated by corresponding radii of curvature, varied widely. In comparison to the human specimens, a previously designed prototype talonavicular prosthesis proved somewhat smaller in radius, arc length, and surface area. Experimental studies related to other prosthesis design parameters, besides type and range of motion, are in progress.

scholarly journals Investigation of sectional operating elements for conveying agricultural materials

2020 ◽  
Vol 66 (No. 1) ◽  
pp. 18-26
Author(s):  
Roman Hevko ◽  
Roman Rohatynskyi ◽  
Myroslav Hevko ◽  
Oleh Lyashuk ◽  
Oleksandra Trokhaniak
Keyword(s):  
Experimental Investigation ◽  
Experimental Studies ◽  
Design Parameters ◽  
Radius Of Curvature ◽  
Material Damage ◽  
Technological Parameters ◽  
Screw Conveyer ◽  
Operating Element ◽  
Processing Line ◽  
Agricultural Materials

The paper covers the results of the theoretical and experimental investigation of the developed sectional operating element of a flexible screw conveyer designed for transporting bulk agricultural materials. In order to determine the correlation between the design parameters of the hinged screw sections and the minimum permissible radius of curvature of a processing line, the analytical dependences have been deduced. The results of the experimental studies aimed at determining the efficiency of a screw conveyer and the level of the grain material damage depending on the change in design, kinematic and technological parameters of an operating element are presented.

EXPERIMENTAL STUDIES OF REINFORCED CONCRETE STRUCTURES WITH CROSS-SHAPED SPATIAL CRACK UNDER TORSION WITH BENDING

2020 ◽  
Vol 92 (6) ◽  
pp. 13-25
Author(s):  
Vl.I. KOLCHUNOV ◽  
◽  
A.I. DEMYANOV ◽  
M.M. MIHAILOV ◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Experimental Determination ◽  
Calculation Method ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Design Parameters ◽  
Reinforced Concrete Structures ◽  
Experimental Scheme

The article offers a method and program for experimental studies of reinforced concrete structures with cross-shaped spatial crack under torsion with bending, the main purpose of which is to check the design assumptions and experimental determination of the design parameters of the proposed calculation method. The conducted experimental studies provide an opportunity to test the proposed calculation apparatus and clarify the regularities for determining deflections, angles of rotation of extreme sections, and stresses in the compressed zone of concrete. For analysis, the article presents a typical experimental scheme for the formation and development of cracks in the form of a sweep, as well as characteristic graphs of the dependence of the angles of rotation of end sections.

scholarly journals Morphological Aspects of Ciliary Motility

1967 ◽  
Vol 50 (6) ◽  
pp. 241-258 ◽  
Author(s):  
Peter Satir
Keyword(s):  
The Other ◽  
Radius Of Curvature ◽  
Arc Length ◽  
Apparent Displacement ◽  
Shaft Length ◽  
Ciliary Motility ◽  
Morphological Aspects ◽  
Circular Arcs ◽  
The Relationship

In Elliptio complanatus lateral cilia, two distinct patterns of filament termination can be discerned. In one case, all nine filaments are present and all are single; in the second, at least one filament is missing but doublets are still present. These probably represent different configurations within one cilium in different stroke positions; to get from one to the other, some peripheral filaments must move with respect to others. The data are consistent with the hypothesis that the filaments themselves do not change length, but rather slide past one another to accommodate increasing curvature. The bent regions of the cilium are in the form of circular arcs. In a few cases, apparent displacement of filaments at the tip (Δl) can be shown to be accounted for if we assume that all differences are generated within these arcs. The displacement per degree of bend is 35 A. Regions of bent arc are initially confined to the base of the cilium but move up the shaft as straight regions appear below them. From the relationship between arc length and radius of curvature, a shaft length that is the unit that initially bends and slides may be defined. Quantal displacements of the length of one 14S dynein may perhaps occur at sites between filaments at opposite sides of such a unit as sliding occurs.

Use of Digital Twins for Mathematical Modeling of Ultrasonic Cutting of Titanium Blanks

2021 ◽  
Vol 1037 ◽  
pp. 369-376
Author(s):  
Maxim Ilyushkin ◽  
Kirill Savelev ◽  
Oleg Krupennikov ◽  
Evgeniy S. Kiselev
Keyword(s):  
Mathematical Modeling ◽  
Thermal Power ◽  
Experimental Studies ◽  
Ultrasonic Field ◽  
Design Parameters ◽  
Digital Twins ◽  
Machine Parts ◽  
Cutting Processes ◽  
Stock Removal ◽  
Processing Zone

The paper presents the results of numerical experimental studies of cutting titanium blanks using mathematical modeling programs, which make it possible to completely repeat technological processes in a computer (digital twin). The LS-DYNA product was used as a program to simulate the process of stock removal from titanium blank. It has been established that the use of this method adequately describes the cutting processes, including with the introduction of the energy of an ultrasonic field into the processing zone, can significantly reduce the duration of experimental research and evaluate the influence of the elements of the cutting mode and design parameters of the tool on the thermal power aspects of the formation of new surfaces of machine parts.

Deaf and Hard-of-hearing Users Evaluating Designs for Highlighting Key Words in Educational Lecture Videos

2021 ◽  
Vol 14 (4) ◽  
pp. 1-24
Author(s):  
Sushant Kafle ◽  
Becca Dingman ◽  
Matt Huenerfauth
Keyword(s):  
Experimental Study ◽  
Key Words ◽  
Hard Of Hearing ◽  
Experimental Studies ◽  
Design Parameters ◽  
Educational Video ◽  
Word Level ◽  
Sentence Level ◽  
First Occurrence ◽  
Educational Videos

There are style guidelines for authors who highlight important words in static text, e.g., bolded words in student textbooks, yet little research has investigated highlighting in dynamic texts, e.g., captions during educational videos for Deaf or Hard of Hearing (DHH) users. In our experimental study, DHH participants subjectively compared design parameters for caption highlighting, including: decoration (underlining vs. italicizing vs. boldfacing), granularity (sentence level vs. word level), and whether to highlight only the first occurrence of a repeating keyword. In partial contrast to recommendations in prior research, which had not been based on experimental studies with DHH users, we found that DHH participants preferred boldface, word-level highlighting in captions. Our empirical results provide guidance for the design of keyword highlighting during captioned videos for DHH users, especially in educational video genres.

Experimental and Numerical Modal Analysis of Composite Laminated Shells

2019 ◽  
Vol 161 (A1) ◽  
Keyword(s):  
Heat Dissipation ◽  
Mass Matrix ◽  
Experimental Studies ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Radius Of Curvature ◽  
Lumped Mass ◽  
Auxiliary Equipment ◽  
Mass Model ◽  
Laminated Shells

The presence of cut outs at different positions of laminated shell component in marine and aeronautical structures facilitate heat dissipation, undertaking maintenance, fitting auxiliary equipment, access ports for mechanical and electrical systems, damage inspection and also influences the dynamic behaviour of the structures. The aim of the present study is to establish a comprehensive perspective of dynamic behavior of laminated deep shells (length to radius of curvature ratio less than one) with cut-out by experiments and numerical simulation. The glass epoxy laminated composite shell has been prepared in the laboratory by resin infusion. The experimental free vibration analysis is carried out on laminated shells with and without cut-out. The mass matrix is developed by considering rotary inertia in a lumped mass model in the numerical modeling. The results obtained from numerical and experimental studies are compared for verification and the consistency between mode shapes is established by applying modal assurance criteria.

INFLUENCE OF TECHNOLOGICAL FACTORS ON THE EFFICIENCY OF REMOVAL OF SCALE FROM FLATS FOR HOLLOW BALLS

2021 ◽  
pp. 143-147
Author(s):  
А.В. Панфилова ◽  
А.В. Королев ◽  
О.П. Решетникова ◽  
Б.М. Изнаиров ◽  
А.Н. Васин
Keyword(s):  
Rotation Speed ◽  
Experimental Studies ◽  
Surface Cleaning ◽  
Point Of View ◽  
Design Parameters ◽  
Technological Factors ◽  
Proportional Relationship ◽  
Sheet Products ◽  
Process Factors ◽  
Rolled Surface

Рассматриваются результаты проведения экспериментальных исследований способа удаления окалины с поверхности стального листового проката. Предложен новый способ и устройство для очистки поверхности листового проката от окалины режущими пластинами, вращающимися вокруг оси, перемещающейся поступательно вдоль обрабатываемой поверхности. Пластины наклонены в направлении вектора вращения на угол до 10 градусов и упруго поджимаются к обрабатываемой поверхности. Это обеспечивает возможность в процессе очистки поверхности воспроизводить макронеровности листового проката. Приведены результаты экспериментальных исследований, построены математические и графические зависимости, описывающие влияние факторов процесса на эффективность очистки поверхности проката. Показано, что наиболее значимое влияние на параметр оптимизации оказывает сила воздействия инструмента на поверхность заготовки. Причем это влияние реализуется в прямо пропорциональной зависимости. Другие исследованные факторы, а именно: угол наклона пластины, скорость ее вращения и подача, оказывают значительно меньшее влияние на степень очистки проката. Эти исследования были необходимы с точки зрения определения конструктивных параметров силовых элементов как технологической оснастки, реализующей указанный способ, так и технологической установки в целом. План эксперимента был принят, исходя из реальных производственных возможностей индустриального партнера, и соответствовал классическим представлениям теории резания. Описанные результаты дают возможность планировать дальнейшие эксперименты по изучению направлений использования данного способа Here we consider the results of experimental studies of the method of removing scale from the surface of steel sheet products. We propose a new method and device for cleaning the surface of rolled sheets from scale by cutting plates rotating around an axis moving translationally along the treated surface. The plates are tilted in the direction of the rotation vector at an angle of up to 10 degrees and are elastically pressed to the treated surface. This makes it possible to reproduce the macro-dimensions of sheet metal during the surface cleaning process. We present the results of experimental studies. We constructed mathematical and graphical dependences describing the influence of process factors on the efficiency of cleaning the rolled surface. We show that the most significant influence on the optimization parameter is exerted by the force of the tool's impact on the surface of the workpiece. Moreover, this influence is realized in a directly proportional relationship. Other factors studied, namely the angle of inclination of the plate, its rotation speed and feed, have a much smaller impact on the degree of cleaning of rolled products. These studies were necessary from the point of view of determining the design parameters of the power elements of both the technological equipment implementing this method and the technological installation as a whole. We adopted the experimental plan based on the real production capabilities of the industrial partner and corresponded to the classical concepts of the cutting theory. The described results make it possible to plan further experiments to study the directions of using the method

scholarly journals Evaluating the Subtalar Joint in Tibiotalocalcaneal Nail

2018 ◽  
Vol 3 (3) ◽  
pp. 2473011418S0040
Author(s):  
Megan Reilly ◽  
Kurosh Darvish ◽  
Soroush Assari ◽  
John Cole ◽  
Tyler Wilps ◽  
...  
Keyword(s):  
Surface Area ◽  
Subtalar Joint ◽  
Articular Surface ◽  
Joint Surface ◽  
Central Dome ◽  
Below The Knee ◽  
Joint Surfaces ◽  
Circular Surface ◽  
The Mean ◽  
Pass Through

Category: Hindfoot Introduction/Purpose: In tibiotalocalcaneal nails for arthrodesis, the path of the nail through the subtalar joint has not been well documented. Ideally, the defect caused by reaming and the nail does not pass through the joint surface so that the amount of bony contact between the talus and calcaneus is maintained in order to optimize fusion. Our hypothesis is that the TTC nail does not destroy a significant amount contact area between the talus and calcaneus. However, using larger diameter nails (which are inherently stronger) will have more of an effect on the contact surface. Methods: Five cadaveric below the knee specimens were obtained. The ankle was disarticulated on each specimen. Subsequently, a guidepin was drilled from the central dome of the talus down to the calcaneus. The 11 mm reamer was then passed over the guidepin through the calcaneus to simulate retrograde reaming of a TTC nail. Then, the subtalar joint was dissected open and the articular surface was documented in comparison with the area that was reamed out. Measurements were then made, using software that calculated two dimensional surface area to determine the percentage of actual subtalar joint area that was reamed out. The mean percentage of articular area that was removed with the reamer was then calculated. Results: Among the five specimens, in the calcaneus, the mean total articular area was 599mm2±113 and the mean drilled articular area was 21mm2±16. The percentage of the calcaneal articular surface that was removed with the reamer was 3.4%±1.9. In the talus, the mean total articular area was 782mm2±130 and the mean drilled articular area was 39mm2±18. The percentage of the talar articular surface that was removed with the reamer was 5.0%±2.3. Additionally, an 11 mm reamer makes a circular surface area of 95mm2, and the statistics above indicate that a significant portion of the reamed area is nonarticular, within the calcaneal sulcus or the talar sulcus. Conclusion: In a tibiotalocalcaneal nail the subtalar joint is typically incompletely visualized, however this anatomic study demonstrates that the 11 mm reamer eliminates about 3.4% of the calcaneal articular surface and about 5% of the talar articular surface. Therefore, the majority of the articular surface is left intact, which is ideal in optimizing arthrodesis outcomes. Furthermore, this study could extrapolate the effects of a larger nail on the availability of joint surface. It could also be used to argue for cartilage stripping of the affected joint surfaces in arthrodesis preparation, because the majority of the articular surface is, in fact, left intact.

scholarly journals STUDY OF THE FUNCTIONAL OUTCOME OF SURGICAL MANAGEMENT OF INTRA-ARTICULAR DISTAL HUMERUS FRACTURE (AO/OTA TYPE C) IN ADULTS

2020 ◽  
pp. 1-3
Author(s):  
Ravindra Prasad ◽  
L B Manjhi
Keyword(s):  
Internal Fixation ◽  
Range Of Motion ◽  
Functional Outcome ◽  
Surgical Management ◽  
Distal Humerus ◽  
Humerus Fracture ◽  
Joint Surface ◽  
Distal Humerus Fracture ◽  
Complex Anatomy ◽  
Type C

Introduction: Distal humerus fracture in adults particularly complete articular (AO/OTA Type C) remain some of the most difficult injuries to manage. Complex anatomy of distal humerus combined with multifragmented fracture, sparse soft tissue cover with adjacent neurovascular structures poses great difficulty for treatment. Goal of treatment is to obtain a painless, stable and mobile elbow joint through a systematic approach. Aim: to study the functional outcome of surgical management of complete articular distal humerus fracture in adults. Method: a prospective study comprising of 20 patients treated surgically with open reduction and internal fixation using Orthogonal plating (dorsolateral and medial 3.5mm LCP) through trans olecranon approach. Result: Mean age of patients was 36.6 years (range 19 to 58 years) with male dominance, most fractures were of type 13C1 (AO/OTA). RTA accounts for most common mode of injury, majority of them being left sided. Mean operative time was 130 minutes. Complications included one case of superficial infection, 3 cases of ulnar neuropathy and non-union in 2 cases. Mean range of motion of elbow was 89 degree. Functional outcome assessed using Mayo Elbow Performance Score (MEPS) shown Excellent result in 12 cases, good to fair results in 6 and poor result in 2 cases. Conclusion: Anatomical restoration of joint surface and rigid internal fixation with bicolumnar orthogonal plating allowing early range of motion is the key for obtaining good functional results in complete articular distal humerus fractures. However, outcomes do deteriorate with increasing fracture complexity.

Sign in / Sign up

Export Citation Format

Share Document