scholarly journals Fibre-reinforced polymer strengthening of substandard lap-spliced reinforced concrete members: A comprehensive survey

2016 ◽  
Vol 20 (6) ◽  
pp. 976-1001 ◽  
Author(s):  
Reyes Garcia ◽  
Maurizio Guadagnini ◽  
Kypros Pilakoutas ◽  
Luis A Pech Poot
Keyword(s):  
Reinforced Concrete ◽  
Cost Effective ◽  
Design Guidelines ◽  
Testing Procedures ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Comprehensive Survey ◽  
Fibre Reinforced Polymer ◽  
Frp Strengthening ◽  
Analytical Approaches

Externally bonded Fibre Reinforced Polymer (FRP) confinement is extensively used to improve the bond strength of substandard lap spliced steel bars embedded in reinforced concrete (RC) components. However, the test results from bond tests on such bond-deficient components are not fully conclusive, which is reflected in the few design guidelines available for FRP strengthening. For the first time, this article presents a comprehensive survey on FRP strengthening of substandard lap-spliced RC members, with emphasis on the adopted experimental methodologies and analytical approaches developed to assess the effectiveness of FRP in controlling bond-splitting failures. The main findings and shortcomings of previous investigations are critically discussed and further research needs are identified. This review contributes towards the harmonisation of testing procedures so as to facilitate the development of more accurate predictive models, thus leading to more cost-effective strengthening interventions.

scholarly journals OPTIMISATION OF THICKNESS OF FIBRE REINFORCED POLYMER SHEETS FOR STRENGTHENING REINFORCED CONCRETE BEAMS WITH FLEXURAL DEFICIENCY

2016 ◽  
Vol 36 (1) ◽  
pp. 45-49
Author(s):  
JM Kaura
Keyword(s):  
Reinforced Concrete ◽  
High Capacity ◽  
Cost Effective ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Reduced Gradient ◽  
Generalized Reduced Gradient

The use of Fiber Reinforced Polymer (FRP) is becoming a widely accepted solution for repairing and strengthening of deteriorated reinforced concrete members, to restore their load carrying capacities. One of the major concerns in the use of FRP is its cost. This therefore calls for the use of efficient and cost effective design approach. Design efficiency in terms of cost can be achieved through optimisation. In the present paper, Generalized Reduced Gradient (GRG) optimisation technique was employed to optimize the strengthening cost of a simply supported reinforced concrete beam strengthened with Fibre Reinforced Polymer (FRP). Optimum design charts for the considered problem were presented. The results showed that considerable savings in thickness can be achieved using FRP of high modulus of elasticity. For example at very high capacity reduction say 70% (kc = 0.3), the required FRP thicknesses for FRP with elastic moduli of 25GPa, 50GPa, 75GPa, 100GPa, 125GPa and 150GPa are respectively equal to 2.5mm, 1.75mm, 0.75mm, 0.6mm, 0.5mm and 0.4mm.  http://dx.doi.org/10.4314/njt.v36i1.7

A review on experimental flexural cracking in FRP reinforced concrete members

2019 ◽  
Author(s):  
Cristina Barris ◽  
Paula Zubillaga ◽  
Lluis Torres
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Design Guidelines ◽  
Flexural Members ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Maximum Crack ◽  
The Relationship ◽  
Frp Bars

<p>This paper aims to assess the relationship among crack width and several influencing parameters of Fibre Reinforced Polymer (FRP) Reinforced Concrete (RC) flexural members. A database with the results of 133 concrete specimens reinforced with different types of FRP bars available in the literature has been collected and analysed. A bond coefficient <i>k</i>b has been adjusted for the maximum crack width of all specimens by using ACI-440 and ISIS Canada design guidelines in the service range, obtaining a mean bond coefficient of 1.11 and 0.72, respectively. The effect of the surface treatment and modulus of elasticity of the FRP rebar, and the <i>n·</i> ratio on the bond coefficient have been studied, obtaining no significant influence of the studied parameters due to the high scatter of results.</p>

Minimum thickness of concrete members reinforced with fibre reinforced polymer bars

2001 ◽  
Vol 28 (4) ◽  
pp. 583-592 ◽  
Author(s):  
Amin Ghali ◽  
Tara Hall ◽  
William Bobey
Keyword(s):  
Reinforced Concrete ◽  
Minimum Thickness ◽  
Reinforced Polymers ◽  
Flexural Members ◽  
Steel Reinforced Concrete ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Steel Bars ◽  
Fibre Reinforced Polymer ◽  
Frp Bars

To avoid excessive deflection most design codes specify the ratio (l/h)s, the span to minimum thickness of concrete members without prestressing. Use of the values of (l/h)s specified by the codes, in selecting the thickness of members, usually yields satisfactory results when the members are reinforced with steel bars. Fibre reinforced polymer (FRP) bars have an elastic modulus lower than that of steel. As a result, the values of (l/h)s specified in codes for steel-reinforced concrete would lead to excessive deflection if adopted for FRP-reinforced concrete. In this paper, an equation is developed giving the ratio (l/h)f for use with FRP bars in terms of (l/h)s and (εs/εf), where εs and εf are the maximum strain allowed at service in steel and FRP bars, respectively. To control the width of cracks, ACI 318-99 specifies εs = 1200 × 10–6 for steel bars having a modulus of elasticity, Es, of 200 GPa and a yield strength, fy, of 400 MPa. At present, there is no value specified for εf; a value is recommended in this paper.Key words: concrete, cracking, deflection, fibre reinforced polymers, flexural members, minimum thickness.

scholarly journals FLEXURAL CAPACITY OF CONCRETE BEAMS REINFORCED WITH STEEL AND FIBRE‐REINFORCED POLYMER (FRP) BARS

2004 ◽  
Vol 10 (3) ◽  
pp. 209-215
Author(s):  
Hau Yan Leung
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Beam Design ◽  
Reinforced Concrete Member ◽  
Current Design ◽  
Fibre Reinforced Polymer ◽  
Steel Rebars ◽  
Frp Bars

Although much research on concrete beams reinforced with fibre‐reinforced polymer (FRP) rods has been conducted in recent years, their use still does not receive the attention it deserves from practicising engineers. This is attributed to the fact that FRP is brittle in nature and the collapse of FRP‐reinforced concrete member may be catastrophic. A rational beam design can incorporate a hybrid use of FRP rods and steel rods. Current design codes only deal with steel‐reinforced or FRP‐reinforced concrete members. Therefore in this study some design charts and equations for concrete beam sections reinforced with FRP rods and steel rebars were generated. Results from the theoretical derivations agreed well with experimental data.

Effect of freeze–thaw cycling on the behaviour of reinforced concrete beams strengthened in flexure with fibre reinforced polymer sheets

2003 ◽  
Vol 30 (6) ◽  
pp. 1081-1088 ◽  
Author(s):  
Mark F Green ◽  
Aaron J.S Dent ◽  
Luke A Bisby
Keyword(s):  
Reinforced Concrete ◽  
Test Data ◽  
Concrete Beams ◽  
Design Guidelines ◽  
Reinforced Concrete Beams ◽  
Bending Test ◽  
Small Scale ◽  
Freeze Thaw ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer

Externally bonded fibre reinforced polymer (FRP) plates and sheets for strengthening and rehabilitating existing reinforced concrete structures have recently received a great deal of attention within the civil engineering community. Many tests have shown the benefits of FRP, but more information is required on their behaviour in cold regions. Twenty-seven small-scale concrete beams (100 mm × 150 mm × 1220 mm) were strengthened with FRP in flexure (and in some cases also in shear), subjected to up to 200 freeze–thaw cycles, and tested to failure in four-point bending. Test results were compared with those predicted by theoretical models and reasonable agreement between the tests and the models was obtained. Current design guidelines for FRP-strengthened beams were compared against the test data and were found to be adequate for the artificially aged beams. The test data also indicated that no significant damage to the glass or carbon FRP-strengthened concrete beams had occurred because of freeze–thaw cycling.Key words: concrete, rehabilitation, fibre reinforced polymers, FRP, beams, freeze–thaw, cold region engineering, flexure, external strengthening.

scholarly journals Application of Sustainable Bamboo-Based Composite Reinforcement in Structural-Concrete Beams: Design and Evaluation

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 696 ◽  
Author(s):  
Alireza Javadian ◽  
Ian F. C. Smith ◽  
Dirk E. Hebel
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Design Guidelines ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Structural Concrete ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Composite Reinforcement

Reinforced concrete is the most widely used building material in history. However, alternative natural and synthetic materials are being investigated for reinforcing concrete structures, given the limited availability of steel in developing countries, the rising costs of steel as the main reinforcement material, the amount of energy required by the production of steel, and the sensitivity of steel to corrosion. This paper reports on a unique use of bamboo as a sustainable alternative to synthetic fibers for production of bamboo fiber-reinforced polymer composite as reinforcement for structural-concrete beams. The aim of this study is to evaluate the feasibility of using this novel bamboo composite reinforcement system for reinforced structural-concrete beams. The bond strength with concrete matrix, as well as durability properties, including the water absorption and alkali resistance of the bamboo composite reinforcement, are also investigated in this study. The results of this study indicate that bamboo composite reinforced concrete beams show comparable ultimate loads with regards to fiber reinforced polymer (FRP) reinforced concrete beams according to the ACI standard. Furthermore, the results demonstrate the potential of the newly developed bamboo composite material for use as a new type of element for non-deflection-critical applications of reinforced structural-concrete members. The design guidelines that are stated in ACI 440.1R-15 for fiber reinforced polymer (FRP) reinforcement bars are also compared with the experimental results that were obtained in this study. The American Concrete Institute (ACI) design guidelines are suitable for non-deflection-critical design and construction of bamboo-composite reinforced-concrete members. This study demonstrates that there is significant potential for practical implementation of the bamboo-composite reinforcement described in this paper. The results of this study can be utilized for construction of low-cost and low-rise housing units where the need for ductility is low and where secondary-element failure provides adequate warning of collapse.

A review on the behaviour of reinforced concrete beams with fibre-reinforced polymer-strengthened web openings

2021 ◽  
pp. 136943322110463
Author(s):  
Xuefei Nie ◽  
Shishun Zhang ◽  
Zeyu Gao ◽  
Zhuo Zeng
Keyword(s):  
Reinforced Concrete ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Web Openings ◽  
Web Opening ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Frp Strengthening ◽  
The Web

Web openings often need to be created in reinforced concrete (RC) beams for the passages of utility ducts and/or pipes. Such web openings reduce the cross-section area of the beam in the affected region, leading to decrease in its load-carrying capacity and stiffness. Therefore, a fibre-reinforced polymer (FRP)-strengthening system generally needs to be applied around the web opening to ensure the safety of the weakened beam. A number of studies have been conducted by researchers all over the world to examine the behaviour of RC beams with FRP-strengthened web opening/web openings, and plenty of useful findings have been generated. This article presents a critical literature review of existing relevant research from three aspects: experimental studies, numerical studies and theoretical studies. The effect of main factors, including the size, shape, location and number of the web opening, the shape and shear span ratio of the beam, the concrete strength, the loading scheme and the FRP-strengthening scheme, on the structural performance of RC beams with FRP-strengthened web opening/web openings have been thoroughly analysed and discussed. Finally, directions for future research based on the gaps which exist in existing studies are pointed out.

Sign in / Sign up

Export Citation Format

Share Document