scholarly journals OPTIMISATION OF THICKNESS OF FIBRE REINFORCED POLYMER SHEETS FOR STRENGTHENING REINFORCED CONCRETE BEAMS WITH FLEXURAL DEFICIENCY

2016 ◽  
Vol 36 (1) ◽  
pp. 45-49
Author(s):  
JM Kaura
Keyword(s):  
Reinforced Concrete ◽  
High Capacity ◽  
Cost Effective ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Reduced Gradient ◽  
Generalized Reduced Gradient

The use of Fiber Reinforced Polymer (FRP) is becoming a widely accepted solution for repairing and strengthening of deteriorated reinforced concrete members, to restore their load carrying capacities. One of the major concerns in the use of FRP is its cost. This therefore calls for the use of efficient and cost effective design approach. Design efficiency in terms of cost can be achieved through optimisation. In the present paper, Generalized Reduced Gradient (GRG) optimisation technique was employed to optimize the strengthening cost of a simply supported reinforced concrete beam strengthened with Fibre Reinforced Polymer (FRP). Optimum design charts for the considered problem were presented. The results showed that considerable savings in thickness can be achieved using FRP of high modulus of elasticity. For example at very high capacity reduction say 70% (kc = 0.3), the required FRP thicknesses for FRP with elastic moduli of 25GPa, 50GPa, 75GPa, 100GPa, 125GPa and 150GPa are respectively equal to 2.5mm, 1.75mm, 0.75mm, 0.6mm, 0.5mm and 0.4mm.  http://dx.doi.org/10.4314/njt.v36i1.7

scholarly journals Fibre-reinforced polymer strengthening of substandard lap-spliced reinforced concrete members: A comprehensive survey

2016 ◽  
Vol 20 (6) ◽  
pp. 976-1001 ◽  
Author(s):  
Reyes Garcia ◽  
Maurizio Guadagnini ◽  
Kypros Pilakoutas ◽  
Luis A Pech Poot
Keyword(s):  
Reinforced Concrete ◽  
Cost Effective ◽  
Design Guidelines ◽  
Testing Procedures ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Comprehensive Survey ◽  
Fibre Reinforced Polymer ◽  
Frp Strengthening ◽  
Analytical Approaches

Externally bonded Fibre Reinforced Polymer (FRP) confinement is extensively used to improve the bond strength of substandard lap spliced steel bars embedded in reinforced concrete (RC) components. However, the test results from bond tests on such bond-deficient components are not fully conclusive, which is reflected in the few design guidelines available for FRP strengthening. For the first time, this article presents a comprehensive survey on FRP strengthening of substandard lap-spliced RC members, with emphasis on the adopted experimental methodologies and analytical approaches developed to assess the effectiveness of FRP in controlling bond-splitting failures. The main findings and shortcomings of previous investigations are critically discussed and further research needs are identified. This review contributes towards the harmonisation of testing procedures so as to facilitate the development of more accurate predictive models, thus leading to more cost-effective strengthening interventions.

Behaviour of reinforced GFRP bars concrete beams having strengthened splices using CFRP sheets

2021 ◽  
pp. 136943322110015
Author(s):  
Akram S. Mahmoud ◽  
Ziadoon M. Ali
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
New Method ◽  
Gfrp Bars ◽  
Reinforced Polymer ◽  
Strength Capacity ◽  
Cfrp Sheet ◽  
Carbon Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer

When glass fibre-reinforced polymer (GFRP) bar splices are used in reinforced concrete sections, they affect the structural performance in two different ways: through the stress concentration in the section, and through the configuration of the GFRP–concrete bond. This study experimentally investigated a new method for increasing the bond strength of a GFRP lap (two GFRP bars connected together) using a carbon fibre-reinforced polymer (CFRP) sheet coated in epoxy resin. A new splicing method was investigated to quantify the effect of the bar surface bond on the development length, with reinforced concrete beams cast with laps in the concrete reinforcing bars at a known bending span length. Specimens were tested in four-point flexure tests to assess the strength capacity and failure mode. The results were summarised and compared within a standard lap made according to the ACI 318 specifications. The new method for splicing was more efficient for GFRP splice laps than the standard lap method. It could also be used for head-to-head reinforcement bar splices with the appropriate CFRP lapping sheets.

Minimum thickness of concrete members reinforced with fibre reinforced polymer bars

2001 ◽  
Vol 28 (4) ◽  
pp. 583-592 ◽  
Author(s):  
Amin Ghali ◽  
Tara Hall ◽  
William Bobey
Keyword(s):  
Reinforced Concrete ◽  
Minimum Thickness ◽  
Reinforced Polymers ◽  
Flexural Members ◽  
Steel Reinforced Concrete ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Steel Bars ◽  
Fibre Reinforced Polymer ◽  
Frp Bars

To avoid excessive deflection most design codes specify the ratio (l/h)s, the span to minimum thickness of concrete members without prestressing. Use of the values of (l/h)s specified by the codes, in selecting the thickness of members, usually yields satisfactory results when the members are reinforced with steel bars. Fibre reinforced polymer (FRP) bars have an elastic modulus lower than that of steel. As a result, the values of (l/h)s specified in codes for steel-reinforced concrete would lead to excessive deflection if adopted for FRP-reinforced concrete. In this paper, an equation is developed giving the ratio (l/h)f for use with FRP bars in terms of (l/h)s and (εs/εf), where εs and εf are the maximum strain allowed at service in steel and FRP bars, respectively. To control the width of cracks, ACI 318-99 specifies εs = 1200 × 10–6 for steel bars having a modulus of elasticity, Es, of 200 GPa and a yield strength, fy, of 400 MPa. At present, there is no value specified for εf; a value is recommended in this paper.Key words: concrete, cracking, deflection, fibre reinforced polymers, flexural members, minimum thickness.

scholarly journals FLEXURAL CAPACITY OF CONCRETE BEAMS REINFORCED WITH STEEL AND FIBRE‐REINFORCED POLYMER (FRP) BARS

2004 ◽  
Vol 10 (3) ◽  
pp. 209-215
Author(s):  
Hau Yan Leung
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Members ◽  
Reinforced Polymer ◽  
Beam Design ◽  
Reinforced Concrete Member ◽  
Current Design ◽  
Fibre Reinforced Polymer ◽  
Steel Rebars ◽  
Frp Bars

Although much research on concrete beams reinforced with fibre‐reinforced polymer (FRP) rods has been conducted in recent years, their use still does not receive the attention it deserves from practicising engineers. This is attributed to the fact that FRP is brittle in nature and the collapse of FRP‐reinforced concrete member may be catastrophic. A rational beam design can incorporate a hybrid use of FRP rods and steel rods. Current design codes only deal with steel‐reinforced or FRP‐reinforced concrete members. Therefore in this study some design charts and equations for concrete beam sections reinforced with FRP rods and steel rebars were generated. Results from the theoretical derivations agreed well with experimental data.

Numerical Analysis of Reinforced Concrete Beam Strengthened with CFRP or GFRP Laminates

2016 ◽  
Vol 707 ◽  
pp. 51-59 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Rania Khattab
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

The behaviour of reinforced concrete beam strengthened with Carbon Fiber Reinforced Polymer (CFRP) and Glass fiber reinforced polymer GFRP laminates was investigated using finite element models and the results are presented in this paper. The numerical investigation assessed the effect of the configuration of FRP strengthening laminates on the behaviour of concrete beams. The load-deflection behaviour, and ultimate load of strengthened beam were compared to those of un-strengthened concrete beams. It was shown that using U-shaped FRP sheets increased the ultimate load. The stiffness of the strengthed beam also increased after first yielding of steel reinforcing bars. At was also observed that strengthening beams with FRP laminates to one-fourth of the beam span, modifies the failure of the beam from shear-controlled near the end of the unstrengthened beam, to flexure-controlled near mid-span. CFRP produced better results compared GFRP in terms of the ability to enhance the behavior of strengthenened reinforced concrete beams.

scholarly journals Efficacy of Thermally Conditioned Sisal FRP Composite on the Shear Characteristics of Reinforced Concrete Beams

2013 ◽  
Vol 2013 ◽  
pp. 1-14 ◽  
Author(s):  
Tara Sen ◽  
H. N. Jagannatha Reddy
Keyword(s):  
Reinforced Concrete ◽  
Polymer Composite ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Shear Strengthening ◽  
Sisal Fibre ◽  
Reinforced Polymer ◽  
Wide Range ◽  
Fibre Reinforced Polymer ◽  
Fracture Study

The development of commercially viable composites based on natural resources for a wide range of applications is on the rise. Efforts include new methods of production and the utilization of natural reinforcements to make biodegradable composites with lignocellulosic fibers, for various engineering applications. In this work, thermal conditioning of woven sisal fibre was carried out, followed by the development of woven sisal fibre reinforced polymer composite system, and its tensile and flexural behaviour was characterized. It was observed that thermal conditioning improved the tensile strength and the flexural strength of the woven sisal fibre composites, which were observed to bear superior values than those in the untreated ones. Then, the efficacy of woven sisal fibre reinforced polymer composite for shear strengthening of reinforced concrete beams was evaluated using two types of techniques: full and strip wrapping techniques. Detailed analysis of the load deflection behaviour and fracture study of reinforced concrete beams strengthened with woven sisal under shearing load were carried out, and it was concluded that woven sisal FRP strengthened beams, underwent very ductile nature of failure, without any delamination or debonding of sisal FRP, and also increased the shear strength and the first crack load of the reinforced concrete beams.

Sign in / Sign up

Export Citation Format

Share Document