Characterization of Areva javanica fiber – A possible replacement for synthetic acrylic fiber in the disc brake pad

2018 ◽  
Vol 49 (3) ◽  
pp. 294-317 ◽  
Author(s):  
Md Javeed Ahmed ◽  
MA Sai Balaji ◽  
SS Saravanakumar ◽  
MR Sanjay ◽  
P Senthamaraikannan
Keyword(s):  
Wear Test ◽  
Disc Brake ◽  
Brake Pad ◽  
X Ray Diffraction ◽  
Acrylic Fiber ◽  
Force Microscopy ◽  
Atomic Force ◽  
Ft Ir

Areva javanica (AJ), a natural cotton flowers fiber of Amaranthaceae family was taken up for the study of its possible utilization in a friction composite. The chemical composition of Areva javanica fiber (AJF) such as cellulose, lignin, ash, moisture, wax content, and density was evaluated. In addition to these, Fourier transform infrared (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential scanning calorimeter (DSC) tests were performed. The surface roughness of AJ fiber was estimated using atomic force microscopy (AFM) and the statistical analysis using Weibull distribution was carried out to identify the diameter of AJ fiber. TGA studies revealed its moderate thermal resistance upto 219℃, and a density of 1.4005 g/cc was estimated of AJF. An attempt was made to make use of the AJF as a potential reinforcement material for acrylic fibers in an organic disc brake pad formulation. Upon fibrization, AJ fibrillates and forms a dense structure, a vital property required for the production of a brake pad. The role of AJ fiber in brake pad was studied by investigating the behavior of fibers from the mixing stage to the cured brake pad. Results revealed that the developed brake pad had a density of 2.01 g/cc, hardness HRS 91, Loss on ignition 21.68%, and cold and hot shear strengths of 44 and 27 kg/cm2, respectively. These values were very close to that of an Acrylic fiber based brake pad. The wear test using Friction Assessment and Screening test (FAST) gave the wear percentage of 0.0187 in3/Hp-h which was found to be 16% higher than AJF (0.0159 in3/Hp-hr) based brake pad.

The Microstructural Characterization of Nanocrystalline CeO2 Ceramics Produced by the Sol-Gel Method

1994 ◽  
Vol 343 ◽  
Author(s):  
F. Czerwinski ◽  
J.A. Szpunar
Keyword(s):  
Sol Gel ◽  
Microstructural Characterization ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Structure Of Coatings ◽  
Heating Up

ABSTRACTCeO2 ceramics were manufactured in the form of surface coatings deposited onto various substrates by sol-gel technology. The size of the CeO2 crystallites, dried at room temperature, was about 5 nm and did not change significantly after heating, up to 680 K. Further increase of the temperature resulted in a rapid growth of crystallites. The process of growth depends also on the film thickness and nature of substrate. The results obtained using thermogravimetric analysis (TGA) and infrared spectroscopy (IR) demonstrated that the thermal decomposition of gel was completed at about 750 K. There was no evident texture in both the as-deposited state and after heat-treatment. X-ray diffraction (XRD), the atomic force microscopy (AFM), and transmission electron microscopy (TEM) were used to characterize the structure of coatings. The examples of application of CeO2 ceramics as coatings for high temperature corrosion protection are presented. The role of size of CeO2 particles in modification of grain boundary transport is discussed.

scholarly journals Morphometric characterization of fibrinogen's αC regions and their role in fibrin self-assembly and molecular organization

Nanoscale ◽  
2017 ◽  
Vol 9 (36) ◽  
pp. 13707-13716 ◽  
Author(s):  
Anna D. Protopopova ◽  
Rustem I. Litvinov ◽  
Dennis K. Galanakis ◽  
Chandrasekaran Nagaswami ◽  
Nikolay A. Barinov ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Self Assembly ◽  
Molecular Organization ◽  
Microscopy Imaging ◽  
Force Microscopy ◽  
Atomic Force ◽  
Atomic Force Microscopy Imaging ◽  
Morphometric Characterization

High-resolution atomic force microscopy imaging reveals the role of fibrinogen αC regions in the early stages of fibrin self-assembly.

scholarly journals Optical, Structural and Electrical Properties of Electrochemical Synthesis of Thin Film of Polyaniline

2018 ◽  
Vol 15 (1) ◽  
pp. 73-80 ◽  
Author(s):  
Baghdad Science Journal
Keyword(s):  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Structural And Electrical Properties ◽  
A Cell ◽  
Ft Ir ◽  
Ir And Raman

Polyaniline membranes of aniline were produced using an electrochemical method in a cell consisting of two poles. The effect of the vaccination was observed on the color of membranes of polyaniline, where analysis as of blue to olive green paints. The sanction of PANI was done by FT-IR and Raman techniques. The crystallinity of the models was studied by X-ray diffraction technique. The different electronic transitions of the PANI were determined by UV-VIS spectroscopy. The electrical conductivity of the manufactured samples was measured by using the four-probe technique at room temperature. Morphological studies have been determined by Atomic force microscopy (AFM). The structural studies have been measured by (SEM).

Growth and Characterization of bulk GaN by Ga Vapor Transport

2004 ◽  
Vol 831 ◽  
Author(s):  
Phanikumar Konkapaka ◽  
Huaqiang Wu ◽  
Yuri Makarov ◽  
Michael G. Spencer
Keyword(s):  
Growth Rates ◽  
Vapor Transport ◽  
Spiral Growth ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Bulk Gan ◽  
Diffraction Patterns

ABSTRACTBulk GaN crystals of dimensions 8.5 mm × 8.5 mm were grown at growth rates greater than 200μm/hr using Gallium Vapor Transport technique. GaN powder and Ammonia were used as the precursors for growing bulk GaN. Nitrogen is used as the carrier gas to transport the Ga vapor that was obtained from the decomposition of GaN powder. During the process, the source GaN powder was kept at 1155°C and the seed at 1180°C. Using this process, it was possible to achieve growth rates of above 200 microns/hr. The GaN layers thus obtained were characterized using X-Ray diffraction [XRD], scanning electron microscopy [SEM], and atomic force microscopy [AFM]. X-ray diffraction patterns showed that the grown GaN layers are single crystals oriented along c direction. AFM studies indicated that the dominant growth mode was dislocation mediated spiral growth. Electrical and Optical characterization were also performed on these samples. Hall mobility measurements indicated a mobility of 550 cm2/V.s and a carrier concentration of 6.67 × 1018/cm3

scholarly journals Synthesis and Characterization of PLA-Micro-structured Hydroxyapatite Composite Films

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 274 ◽  
Author(s):  
Andreea Madalina Pandele ◽  
Andreea Constantinescu ◽  
Ionut Cristian Radu ◽  
Florin Miculescu ◽  
Stefan Ioan Voicu ◽  
...  
Keyword(s):  
Composite Films ◽  
Synthesis Method ◽  
Polymer Chains ◽  
Force Microscopy ◽  
Degradation Temperature ◽  
Atomic Force ◽  
Hydroxyapatite Composite ◽  
Ft Ir ◽  
Ir And Raman

This article presents a facile synthesis method used to obtain new composite films based on polylactic acid and micro-structured hydroxyapatite particles. The composite films were synthesized starting from a polymeric solution in chloroform (12 wt.%) in which various concentrations of hydroxyapatite (1, 2, and 4 wt.% related to polymer) were homogenously dispersed using ultrasonication followed by solvent evaporation. The synthesized composite films were morphologically (through SEM and atomic force microscopy (AFM)) and structurally (through FT-IR and Raman spectroscopy) characterized. The thermal behavior of the composite films was also determined. The SEM and AFM analyses showed the presence of micro-structured hydroxyapatite particles in the film’s structure, as well as changes in the surface morphology. There was a significant decrease in the crystallinity of the composite films compared to the pure polymer, this being explained by a decrease in the arrangement of the polymer chains and a concurrent increase in the degree of their clutter. The presence of hydroxyapatite crystals did not have a significant influence on the degradation temperature of the composite film.

scholarly journals Cellulose-Cyclodextrin Co-Polymer for the Removal of Cyanotoxins on Water Sources

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2075
Author(s):  
Diego Gomez-Maldonado ◽  
Iris Beatriz Vega Erramuspe ◽  
Ilari Filpponen ◽  
Leena-Sisko Johansson ◽  
Salvatore Lombardo ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Cellulose Nanofibrils ◽  
Human Consumption ◽  
Nutrient Runoff ◽  
Force Microscopy ◽  
Atomic Force ◽  
Safe Limits ◽  
Ft Ir ◽  
Recreational Use

With increasing global water temperatures and nutrient runoff in recent decades, the blooming season of algae lasts longer, resulting in toxin concentrations that exceed safe limits for human consumption and for recreational use. From the different toxins, microcystin-LR has been reported as the main cyanotoxin related to liver cancer, and consequently its abundance in water is constantly monitored. In this work, we report a methodology for decorating cellulose nanofibrils with β-cyclodextrin or with poly(β-cyclodextrin) which were tested for the recovery of microcystin from synthetic water. The adsorption was followed by Quartz Crystal Microbalance with Dissipation monitoring (QCM-D), allowing for real-time monitoring of the adsorption behavior. A maximum recovery of 196 mg/g was obtained with the modified by cyclodextrin. Characterization of the modified substrate was confirmed with Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Photoelectron Spectroscopy (XPS), Thermogravimetric Analysis (TGA), and Atomic Force Microscopy (AFM).

Epitaxial Growth and Characterization of the Ordered Vacancy Compound CuIn3Se5 on GaAs (100) Fabricated by Molecular Beam Epitaxy

1994 ◽  
Vol 340 ◽  
Author(s):  
Art J. Nelson ◽  
M. Bode ◽  
G. Horner ◽  
K. Sinha ◽  
John Moreland
Keyword(s):  
Molecular Beam Epitaxy ◽  
Epitaxial Growth ◽  
Molecular Beam ◽  
Structural Defects ◽  
X Ray Diffraction ◽  
Symmetric Vibration ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron

ABSTRACTEpitaxial growth of the ordered vacancy compound (OVC) CuIn3Se5 has been achieved on GaAs (100) by molecular beam epitaxy (MBE) from Cu2Se and In2Se3 sources. Electron probe microanalysis and X-ray diffraction have confirmed the composition for the 1-3-5 OVC phase and that the film is single crystal Culn3Se5 (100). Transmission electron microscopy (TEM) characterization of the material also showed it to be single crystalline. Structural defects in the layer consisted mainly of stacking faults. Photoluminescence (PL) measurements performed at 7.5 K indicate that the bandgap is 1.28 eV. Raman spectra reveal a strong polarized peak at 152 cm−1, which is believed to arise from the totally symmetric vibration of the Se atoms in the lattice. Atomic force microscopy reveals faceting in a preferred (100) orientation.

Characterization of Asymmetric Polydiacetylene Ultrathin Films

1995 ◽  
Vol 382 ◽  
Author(s):  
D. W. Cheong ◽  
V. Shivshankar ◽  
H. C. Wang ◽  
C. M. Sung ◽  
J. Kumar ◽  
...  
Keyword(s):  
Ultrathin Films ◽  
Second Harmonic ◽  
Film Deposition ◽  
Asymmetric Structure ◽  
Blodgett Film ◽  
Force Microscopy ◽  
Langmuir Blodgett ◽  
Atomic Force ◽  
Ft Ir

ABSTRACTNonlinear optical (NLO) ultrathin films of a preforrned asymmetric polydiacetylene have been fabricated by Z-type Langmuir-Blodgett film deposition from the air-water interface. Induced in-plane orientation of the polydiacetylene backbone on the substrates has been confirmed by UV/Vis, FT-IR dichroism, and degenerate four wave mixing (DFWM) studies. All the measurements indicate that the backbone is prefe rentially oriented along the dipping direction. Second harmonic generation study suggests that the LB multilayers form an asymmetric structure (Z-type) due to the accumulation of 2-dimensional ordered monolayer and the dominant induced second order polarization is in the plane of the film. The film morphology and molecular orientation have been investigated by atomic force microscopy (AFM).

Stability and Structural Characterization of Epitaxial NdNiO3 Films Grown by Pulsed Laser Deposition

2000 ◽  
Vol 658 ◽  
Author(s):  
Trong-Duc Doan ◽  
Cobey Abramowski ◽  
Paul A. Salvador
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Monoclinic Distortion

ABSTRACTThin films of NdNiO3 were grown using pulsed laser deposition on single crystal substrates of [100]-oriented LaAlO3 and SrTiO3. X-ray diffraction and reflectivity, scanning electron microscopy, and atomic force microscopy were used to characterize the chemical, morphological and structural traits of the thin films. Single-phase epitaxial films are grown on LaAlO3 and SrTiO3 at 625°C in an oxygen pressure of 200 mTorr. At higher temperatures, the films partially decompose to Nd2NiO4 and NiO. The films are epitaxial with the (101) planes (orthorhombic Pnma notation) parallel to the substrate surface. Four in-plane orientational variants exist that correspond to the four 90° degenerate orientations of the film's [010] with respect to the in-plane substrate directions. Films are observed to be strained in accordance with the structural mismatch to the underlying substrate, and this leads, in the thinnest films on LaAlO3, to an apparent monoclinic distortion to the unit cell.

Effects of Annealing on Pulsed Laser Deposited TiO2 Thin Films

2013 ◽  
Vol 446-447 ◽  
pp. 306-311 ◽  
Author(s):  
Sudhanshu Dwivedi ◽  
Somnath Biswas
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Si Substrates ◽  
Morphological Studies ◽  
Atomic Force ◽  
Deposited Films ◽  
Type Crystal

Mixed phase TiO2 thin films of rutile and anatase type crystal orientations were deposited on Si substrates by pulsed laser deposition (PLD) technique. When annealed at 800°C at 1 mbar oxygen pressure for 3 h, the deposited films transform into a single phase of rutile type. Structural and morphological studies of the as-deposited and annealed films were performed with X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), Raman spectroscopy, and atomic force microscopy (AFM). Photoluminescence (PL) spectroscopy was used for optical characterization of the annealed thin films.

Sign in / Sign up

Export Citation Format

Share Document