scholarly journals Evaluation of residual strength with ultrasonic pulse velocity relationship for concrete exposed to high temperatures

2021 ◽  
Vol 13 (9) ◽  
pp. 168781402110349
Author(s):  
Yeol Choi ◽  
Joo-Won Kang ◽  
Tae-Yeon Hwang ◽  
Chang-Geun Cho
Keyword(s):  
Compressive Strength ◽  
High Temperatures ◽  
Elevated Temperatures ◽  
Linear Equations ◽  
Ultrasonic Pulse Velocity ◽  
Tensile Tests ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Velocity Relationship ◽  
The Difference

This paper presents the results of an experimental investigation on the relationship between strength and ultrasonic pulse velocity (UPV) of concrete exposed to high temperature, especially for a decision of building remodeling of concrete structures. The experiments were conducted at three different initial compressive strength levels for temperature up to 800°C. UPV, Compressive, and splitting tensile tests and UPV measurements were performed for unheated and heated concrete specimens. The measured UPV values in the present work were correlated with compressive and tensile strengths to estimate the strength of concrete. Based on the results, two linear equations for predicting compressive and tensile strength of concrete at elevated temperatures using UPV have been proposed. It is found that the difference of initial compressive strength of concrete does not have a significant effect on the strength reduction ratio after exposed to high temperatures. In addition, the reduction factors of compressive and tensile strengths in the present work do not well comply with the values of suggested by EN 1992-1-2.

Recycled Concrete Using Crushed Construction Waste Bricks Subject to Elevated Temperatures

2010 ◽  
Vol 152-153 ◽  
pp. 1-10
Author(s):  
Chung Ming Ho ◽  
Wei Tsung Tsai
Keyword(s):  
Compressive Strength ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
Plain Concrete ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Recycled Concrete ◽  
Fine Aggregate ◽  
Term Performance

The objectives of this paper are to find the compressive strength and ultrasonic pulse velocity (UPV) of recycled concrete with various percentages of natural fine aggregate replaced by Recycled brick fine aggregate (RBFA) as well as the residual strength and residual UPV of recycled concrete subjected to elevated temperatures. Experiment results showed that the compressive strength and UPV decreased as amount of RBFA in concrete increased, the long-term performance of compressive strength and UPV development increased as the RBFA content increased. The residual strength of recycled concrete increased slightly after heating to 300°C and the residual UPV of recycled concrete decreased gradually as the exposed temperature increased beyond 300°C. In the range of 580 -800°C, recycled concrete lost most of its original compressive strength and UPV. After subjected to the temperature of 800°C, compared to plain concrete, recycled concrete with 100% RBFA had a greater discount rate of compressive strength and UPV of the order of 5-15% and 6-10%. Regression analysis results revealed that the residual strength and residual UPV of recycled concrete had a high relevance after elevated temperatures exposure.

scholarly journals Transport Properties and Resistance Improvement of Ultra-High Performance Concrete (UHPC) after Exposure to Elevated Temperatures

Buildings ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 416
Author(s):  
Yunfeng Qian ◽  
Dingyi Yang ◽  
Yanghao Xia ◽  
Han Gao ◽  
Zhiming Ma
Keyword(s):  
Compressive Strength ◽  
Transport Properties ◽  
High Temperatures ◽  
High Performance ◽  
High Performance Concrete ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Capillary Absorption ◽  
Self Healing

Ultra-high performance concrete (UHPC) has a high self-healing capacity and is prone to bursting after exposure to high temperatures due to its characteristics. This work evaluates the damage and improvement of UHPC with coarse aggregates through mechanical properties (compressive strength and ultrasonic pulse velocity), transport properties (water absorption and a chloride diffusion test), and micro-properties such as X-ray diffraction (XRD), Mercury intrusion porosimetry (MIP), and Scanning electronic microscopy (SEM). The result demonstrates that polypropylene (PP) fibers are more suitable for high temperature tests than polyacrylonitrile (PAN) fibers. The result shows that 400 °C is the critical temperature point. With the increase in temperature, the hydration becomes significant, and the internal material phase changes accordingly. Although the total pore volume increased, the percentage of various types of pores was optimized within 400 °C. The mass loss gradually increased and the ultrasonic pulse velocity gradually decreased. While the compressive strength first increased and then decreased, and the increase occurred within 25–400 °C. As for the transport properties, the chloride migration coefficient and capillary absorption coefficient both increased dramatically due to the higher sensitivity to temperature changes. The results of the property improvement test showed that at temperatures above 800 °C, the compressive strength recovered by more than 65% and the ultrasonic pulse velocity recovered by more than 75%. In terms of transport properties, compared to the results before self-healing, the chloride migration coefficient decreased by up to 59%, compared with 89% for the capillary absorption coefficient, after self-healing at 800 °C. With respect to the enhancement effect after exposure to high temperatures, the environment of a 5% Na2SO4 solution was not as good as the clean water environment. The corresponding changes in microstructure during the high temperatures and the self-healing process can explain the change in the pattern of macroscopic properties more precisely.

scholarly journals The relationship between the compressive strength and ultrasonic pulse velocity concrete with fibers exposed to high temperatures

2018 ◽  
Vol 3 (1) ◽  
pp. 31
Author(s):  
Belaribi Hassiba ◽  
Mellas Mekki ◽  
Rahmani Fraid
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Velocity ◽  
High Temperatures ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Ratio ◽  
Compressive Strength Of Concrete ◽  
The Relationship ◽  
The Waves

The paper analyses the effects of high temperatures on the concrete residual strength using ultrasonic velocity (UPV). An experimental investigation was conducted to study the relationship between UPV residual data and compressive strength of concrete with different mixture proportions, cubic specimens with water-cement ratio of 0.35. They were heated in an electric furnace at temperatures ranging from 200°C to 600°C. In this experiment a comparison was made between the four groups which include two types of fibers steel 0,19%, 0,25% and 0,5%, polypropylene: 0,05%, 0,11% 0,16 % by volume. Cube specimens were tested in order to determine ultrasonic velocity. The compressive strength was tested too. According to the results, relations were established between ultrasonic velocity in the specimens and the compressive strength at different temperature and the range of the velocity of the waves were also determined for this kind of concrete. Result of the test showed that UPV test can be successfully used in order to verify the consistency of structures damaged by fire.

Effect of Elevated Temperature on the Strength and Ultrasonic Pulse Velocity of Glass Fiber and Nano-Clay Concrete

2010 ◽  
Vol 163-167 ◽  
pp. 1532-1539 ◽  
Author(s):  
Chung Ming Ho ◽  
Wei Tsung Tsai
Keyword(s):  
Compressive Strength ◽  
Glass Fiber ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Nano Clay ◽  
Compressive Strength Of Concrete ◽  
Temperature Exposure

The objectives of this paper are to find the strength and ultrasonic pulse velocity (UPV) of concrete adding admixtures by glass fiber and nano-clay. Residual strength and residual UPV of concrete specimens subjected to elevated temperatures are investigated. Experiment results showed that adding glass fiber and nano-clay would be beneficial for the later-age compressive strength of concrete. Adding nano-clay could considerably increase the flexural and split strength and the toughness of concrete. It is revealed that adding nano-clay could significantly maintain residual compressive and split strength of specimens after high temperature exposure. Regression analysis results revealed that the residual strength and residual UPV of concrete specimens had a high relevance after elevated temperatures exposure.

scholarly journals Behavior of Biochar-Modified Cementitious Composites Exposed to High Temperatures

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5414
Author(s):  
Xu Yang ◽  
Run-Sheng Lin ◽  
Yi Han ◽  
Xiao-Yong Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
High Temperatures ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Temperature Resistance ◽  
Residual Compressive Strength ◽  
Scanning Electron

In this study, the effect of biochar on the high temperature resistance of cementitious paste was investigated using multiple experimental methods. The weight loss, cracks, residual compressive strength, and ultrasonic pulse velocity (UPV) of biochar cementitious paste with 2% and 5% biochar exposed to 300, 550 and 900 °C were measured. The products and microstructures of biochar cementitious paste exposed to high temperatures were analyzed by X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy. The results showed that the cracks of specimens exposed to high temperatures decreased with increasing biochar content. The addition of 2% and 5% biochar increased the residual compressive strength of the specimens exposed to 300 °C and the relative residual compressive strength at 550 °C. As the exposure temperature increased, the addition of biochar compensated for the decreasing ultrasonic pulse velocity. The addition of biochar contributed to the release of free water and bound water, and reduced the vapor pressure of the specimen. The addition of biochar did not change the types of functional groups and crystalline phases of the products of cementitious materials exposed to high temperatures. Biochar particles were difficult to observe at 900 °C in scanning electron microscopy images. In summary, because biochar has internal pores, it can improve the high-temperature resistance of cement paste.

scholarly journals Use of Bacteria Externally for Repairing Cracks and Improving Properties of Concrete Exposed to High Temperatures

Crystals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1503
Author(s):  
Milad Nimafar ◽  
Bijan Samali ◽  
Saied Jalil Hosseini ◽  
Alireza Akhlaghi
Keyword(s):  
Electrical Conductivity ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
High Temperatures ◽  
Ultrasonic Pulse Velocity ◽  
Bacillus Sphaericus ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Calcium Carbonate Precipitation ◽  
Bacterial Remediation

The current paper presents the results of an experimental study on the application of calcium carbonate precipitation bacteria as a new approach to repairing damaged concrete when exposed to high temperatures. To do so, cylindrical and cubic concrete specimens were initially exposed to heat in a furnace for 1 h, after reaching two different temperatures of 600 and 800 °C. A heat rate of 5.5 °C per minute was used to achieve the target temperatures. Then, two types of bacteria, namely Sporosarcina pasteurii and Bacillus sphaericus, with cell concentration of 107 cells/mL, were utilized externally, to repair the thermal cracks, enhancing the mechanical properties and durability of the damaged concrete. The efficiency of the bacterial remediation technique was then evaluated through compressive strength, ultrasonic pulse velocity (UPV), and electrical conductivity tests on the control specimens (unexposed to heat), and those exposed to high temperature with or without bacterial healing. The experimental results demonstrate that the compressive strength of the test specimens exposed to temperatures of 600 and 800 °C decreased by about 31–44% compared with the control ones. However, compared to those damaged at 600 and 800 °C, the compressive strength of specimens repaired by the S. pasteurii and the B. sphaericus showed increases of 31–93%. This increase is associated with the precipitation of calcium carbonate in the deep and superficial cracks and pores of the damaged specimens. Furthermore, the ultrasonic pulse velocity of the specimens subjected to bacterial remediation had a significant increase of about 1.65–3.47 times compared with the damaged ones. In addition, the electrical conductivity of repaired specimens decreased by 22–36% compared with the damaged specimens.

PENGKAJIAN KEKUATAN BETON STRUKTUR JEMBATAN PASCA KEBAKARAN

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Sudarmadi Sudarmadi
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Strength Assessment ◽  
Concrete Testing

In this paper a case study about concrete strength assessment of bridge structure experiencing fire is discussed. Assessment methods include activities of visual inspection, concrete testing by Hammer Test, Ultrasonic Pulse Velocity Test, and Core Test. Then, test results are compared with the requirement of RSNI T-12-2004. Test results show that surface concrete at the location of fire deteriorates so that its quality is decreased into the category of Very Poor with ultrasonic pulse velocity ranges between 1,14 – 1,74 km/s. From test results also it can be known that concrete compressive strength of inner part of bridge pier ranges about 267 – 274 kg/cm2 and concrete compressive strength of beam and plate experiencing fire directly is about 173 kg/cm2 and 159 kg/cm2. It can be concluded that surface concrete strength at the location of fire does not meet the requirement of RSNI T-12-2004. So, repair on surface concrete of pier, beam, and plate at the location of fire is required.

Sign in / Sign up

Export Citation Format

Share Document