scholarly journals Optimization of multi variant process parameters to reduce emissions of high sulfur coal during combustion in fluidized bed facility

2021 ◽  
Vol 13 (9) ◽  
pp. 168781402110446
Author(s):  
Bhutta Muhammad Mahmood Aslam ◽  
Shafiq ur Rehman ◽  
Asad Naeem Shah ◽  
Muhammad Sajid Kamran ◽  
Ahmad Naveed ◽  
...  
Keyword(s):  
Particle Size ◽  
Energy Demand ◽  
Gaseous Emissions ◽  
Considerable Decrease ◽  
Molar Ratios ◽  
Bed Temperature ◽  
Salt Range ◽  
Reduce Emissions ◽  
Sulfur Emissions

Pakistan has 185 billion tonnes reserves of coal but unfortunately the quality of 80% of this coal is not good. As the country has a shortage of energy so it is necessary to refine the coal before it can be used to produce electricity. In this sense, this research is very important as it enables indigenous coal to meet the increasing energy demand. This study is focused on the control of sulfur emissions during the combustion of high sulfur Pakistani coal from the Trans Indus Range and the Salt Range. Parameters like Ca/S molar ratios (MRs), limestone particle size, bed temperature, and different percentages of biomass in co-firing with coal have been studied. It is showed that desulfurization of coal was maximum with the fine-sized particles of limestone. Co-firing of moderate quantity biomass exhibited a considerable decrease in SO2 emissions. Results achieved are presented in the form of tables and plots. This study for control of the gaseous emissions from combustion in FBC facility has great potential for new coal based power projects, especially in Pakistan.

scholarly journals The Influence of Extruded Sugar Beet Pulp on Cookies' Nutritional, Physical and Sensory Characteristics

2021 ◽  
Vol 13 (9) ◽  
pp. 5317
Author(s):  
Sonja Simić ◽  
Jovana Petrović ◽  
Dušan Rakić ◽  
Biljana Pajin ◽  
Ivana Lončarević ◽  
...  
Keyword(s):  
Particle Size ◽  
Sugar Beet ◽  
Dietary Fiber ◽  
Wheat Flour ◽  
Nutritional Quality ◽  
Sugar Beet Pulp ◽  
Sensory Characteristics ◽  
Total Dietary Fiber ◽  
Beet Pulp

Sugar beet pulp (SBP) is a by-product of the sugar industry in which the dietary fiber content ranges from 73% to 80%. Compared to cereal fibers mainly used in biscuit production, sugar beet fibers are gluten free and have a perfect ratio of 2/3 insoluble fiber. In this work, sugar beet pulp was extruded with corn grits (ratios of corn grits to sugar beet pulp in extrudates were 85:15, 70:30, and 55:45), and the obtained sugar beet pulp extrudates (SBPEs) were used for improving the nutritional quality of cookies. The wheat flour in cookies was replaced with SBPEs in the amount of 5, 10, and 15%. The influence of three factors (the percentage of sugar beet pulp in the SBPEs, the size of the SBPE particles, and the percentage of wheat flour substituted with SBPEs) and their interactions on the nutritional quality of cookies, as well as their physical and sensory characteristics are examined using the Box–Behnken experimental design. The addition of extruded sugar beet pulp (SBPEs) significantly increased the amount of total dietary fiber and mineral matter of cookies. On the whole, the addition of SBPEs increased cookie hardness, but the hardness decreased with an increase in extrudate particle size. Sensory characteristics (except for the taste) were the most influenced by extrudate particle size.

scholarly journals Modernization of the Public Transport Bus Fleet in the Context of Low-Carbon Development in Poland

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3295
Author(s):  
Maciej Dzikuć ◽  
Rafał Miśko ◽  
Szymon Szufa
Keyword(s):  
Coal Combustion ◽  
Electricity Generation ◽  
Urban Transport ◽  
Rolling Stock ◽  
Low Carbon ◽  
The Public ◽  
Low Carbon Development ◽  
Reduce Emissions ◽  
Excessive Noise

The development of urban transport in recent years has become one of the most important issues related to improving the quality of life in Polish cities. Excessive pollution in the form of greenhouse gases and other harmful substances from buses affects people’s health as does the excessive noise. This article analysed the measures being taken to reduce emissions, and the results showed that it is possible to reduce CO2 emissions by more than 28 thousand megagrams (Mg) per annum. Policymakers in Poland should consider limiting electricity generation through coal combustion and recognize, at least temporarily, CNG/LNG-powered buses as low-carbon rolling stock and co-finance their purchase and the necessary infrastructure.

scholarly journals Syngas Quality as a Key Factor in the Design of an Energy-Efficient Pyrolysis Plant for Scrap Tyres

Proceedings ◽  
2018 ◽  
Vol 2 (23) ◽  
pp. 1455 ◽  
Author(s):  
Dina Czajczyńska ◽  
Renata Krzyżyńska ◽  
Hussam Jouhara
Keyword(s):  
Energy Demand ◽  
Chemical Properties ◽  
Industrial Emissions ◽  
Whole Process ◽  
Start Up ◽  
Key Factor ◽  
Industrial Emissions Directive ◽  
Pyrolytic Oil ◽  
Quality Of Products

In 2016 4.94 million tonnes of tyres were produced. Each tyre eventually become waste and pyrolysis has been considered an effective way of utilizing scrap tyres for several decades. However, pyrolysis has failed many times because the process has a great energy demand and the quality of products is unstable or insufficient for commercial use. Usually plants are focused on the production of pyrolytic oil or char and the gaseous phase is only a by-product. In this paper the importance of composition and quality of pyrolytic gas is emphasized. The main chemical properties make this gas a valuable biofuel that may satisfy energy requirements of the whole process (except for the start-up phase). Available data from literature concerning composition and other features of the pyrolytic gas from scrap tyres obtained at temperatures up to 1000 °C are compared with experimental results. The quality of evolved gases is discussed in the context of the Industrial Emissions Directive (IED), too. Finally, an analysis of the mass balances obtained allows a decision about the business profile and profitability.

Effects of Flour Particle Size and Starch Damage on Processing and Quality of White Salted Noodles

2002 ◽  
Vol 79 (1) ◽  
pp. 64-71 ◽  
Author(s):  
D. W. Hatcher ◽  
M. J. Anderson ◽  
R. G. Desjardins ◽  
N. M. Edwards ◽  
J. E. Dexter
Keyword(s):  
Particle Size

Performance, carcass traits and meat quality of lambs fed with different roughage:concentrate ratios associated with variable physically effective neutral detergent fibre content

2021 ◽  
pp. 1-11
Author(s):  
L. de O. Queiroz ◽  
A. M. Barbosa ◽  
G. B. Mourão ◽  
M. A. Fonseca ◽  
L. F. B. Pinto ◽  
...  
Keyword(s):  
Fatty Acids ◽  
Particle Size ◽  
Meat Quality ◽  
Average Daily Gain ◽  
Carcass Traits ◽  
Faecal Excretion ◽  
Neutral Detergent Fibre ◽  
Fatty Acids Profile ◽  
Colour Parameter

Abstract This study evaluated the effect of roughage:concentrate (R:C) ratio associated with a variable particle size of physically effective neutral detergent fibre (peNDF8) in the forage (Tifton-85 hay) on the performance, carcass traits and meat quality of lambs. Seventy-two 4-month-old, non-castrated Santa Ines male lambs (23.5 ± 2.32 kg BW) were distributed in a completely randomized design, in a 2 × 2 factorial arrangement [two peNDF8 hay particle sizes (13 and 6 mm) and two R:C ratios (700:300 and 500:500 g/kg DM total)]. DMI, DM, NFC and TDN digestibility's, N-intake and N-faecal excretion were affected by the R:C ratio (P < 0.05). However, the N-retained was not affected by the studied variables (P > 0.05). It was observed an interaction (P < 0.05) between the peNDF8 and R:C ratios for final BW, average daily gain (ADG), colour parameters and pH 24 h. The lower roughage ratio provided greater (P < 0.05) concentrations of C14:1, C16:1–cis9, C18:1–cis9, ΣMUFA, Σn–6:Σn–3 and hypocholesterolemic/hypercholesterolemic index, enzymatic activity Δ9desaturase-C16 and -C18. Lambs fed a lower roughage diet had improved performance and feed efficiency, however, presented reduced polyunsaturated fatty acids (PUFA) concentrations in the meat, especially Σn–3 family. Higher roughage diet and larger peNDF8 particle size improved the concentrations of PUFA while decreased Σn–6:Σn–3 ratio in meat. Larger peNDF8 particle size associated with higher roughage proportion, have reduced animal performance however, it increased protein concentration, a* and C* colour parameter without affecting fatty acids profile of Longissimus lumborum muscle.

Composition, particle size, and near-infrared irradiation effects on optical properties of Au–Au2S nanoparticles

2008 ◽  
Vol 23 (1) ◽  
pp. 281-293 ◽  
Author(s):  
Mei Chee Tan ◽  
Jackie Y. Ying ◽  
Gan Moog Chow
Keyword(s):  
Particle Size ◽  
Optical Properties ◽  
Thermal Effects ◽  
Near Infrared ◽  
Sodium Sulfide ◽  
Irradiation Effects ◽  
Absorption Bands ◽  
Molar Ratios ◽  
Nir Absorption ◽  
Structure And Microstructure

Near-infrared (NIR)-absorbing nanoparticles synthesized by the reduction of tetrachloroauric acid (HAuCl4) using sodium sulfide (Na2S) exhibited absorption bands at ∼530 nm and at the NIR region of 650−1100 nm. A detailed study on the structure and microstructure of as-synthesized nanoparticles was reported previously. The as-synthesized nanoparticles were found to consist of amorphous AuxS (x = ∼2), mostly well mixed within crystalline Au. In this work, the optical properties were tailored by varying the precursor molar ratios of HAuCl4 and Na2S. In addition, a detailed study of composition and particle-size effects on the optical properties was discussed. The change of polarizability by the introduction of S in the form of AuxS (x = ∼2) had a significant effect on NIR absorption. Also, it was found in this work that exposure of these particles to NIR irradiation using a Nd:YAG laser resulted in loss of the NIR absorption band. Thermal effects generated during NIR irradiation had led to microstructural changes that modified the optical properties of particles.

Influence of coke breeze particle size on quality of sinter

2008 ◽  
Vol 35 (8) ◽  
pp. 567-574 ◽  
Author(s):  
T. Umadevi ◽  
A. V. Deodhar ◽  
S. Kumar ◽  
C. S. Gururaj Prasad ◽  
M. Ranjan
Keyword(s):  
Particle Size ◽  
Coke Breeze

scholarly journals Opening Material as the Possibility of Elimination Veining in Foundries

2016 ◽  
Vol 16 (3) ◽  
pp. 157-161 ◽  
Author(s):  
M. Hrubovčáková ◽  
I. Vasková ◽  
M. Benková ◽  
M. Conev
Keyword(s):  
Thermal Conductivity ◽  
Particle Size ◽  
Thermal Expansion ◽  
Cast Iron ◽  
Granular Material ◽  
Surface Defects ◽  
Silica Sand ◽  
Iron Castings ◽  
Thermal Dilatation

Abstract The main bulk density representation in the molding material is opening material, refractory granular material with a particle size of 0.02 mm. It forms a shell molds and cores, and therefore in addition to activating the surface of the grain is one of the most important features angularity and particle size of grains. These last two features specify the porosity and therefore the permeability of the mixture, and thermal dilatation of tension from braking dilation, the thermal conductivity of the mixture and even largely affect the strength of molds and cores, and thus the surface quality of castings. [1] Today foundries, which use the cast iron for produce of casts, are struggling with surface defects on the casts. One of these defects are veining. They can be eliminated in several ways. Veining are foundry defects, which arise as a result of tensions generated at the interface of the mold and metal. This tension also arises due to abrupt thermal expansion of silica sand and is therefore in the development of veining on the surface of casts deal primarily influences and characteristics of the filler material – opening material in the production of iron castings.

scholarly journals THE EFFECT OF CAVITATION TREATMENT ON THE EXTINGUISHING OF PARTICLES OF OILS IN FUEL BOILERS

2019 ◽  
Vol 20 (9-10) ◽  
pp. 52-59
Author(s):  
M. A. Taymarov ◽  
R. V. Akhmetova ◽  
S. M. Margulis ◽  
L. I. Kasimova
Keyword(s):  
Particle Size ◽  
Combustion Zone ◽  
Consumption Rate ◽  
Fuel Oil ◽  
Particle Sizes ◽  
Oil Consumption ◽  
Boiler Efficiency ◽  
Large Particles ◽  
Oil Particles

The difficulties of burning the watered fuel oil used at the TPP as a reserve fuel for boilers are associated with its preparation by heating to reduce viscosity and the choice of a method of spraying with nozzles into the combustion zone. The quality of the preparation of fuel oil for combustion affecting the boiler efficiency is estimated by the length of the flame, the presence of burning large particles of fuel oil, the injection of coke and unburned particles onto screen and other heat-receiving surfaces. One of the ways to prepare fuel oil for combustion is cavitation treatment, which results in an emulsion consisting of fine micronsized particles. Heating of fuel oil particles after the nozzle in contact with the combustion zone is due to the flow of radiation from the burning torch. Therefore, in this article, the values of the flux density from the torch during the combustion of fuel oil are experimentally determined. The influence of particle size on the burning rate of the fuel oil M100 with the different density of the thermal radiation of the flame. It is found that the effect of cavitation treatment of fuel oil on the combustion rate is most significantly manifested in particle sizes less than 10 microns. For this purpose, the use of hydrodynamic cavitators are preferred at high fuel oil consumption rate.

scholarly journals KUALITAS PAPAN KOMPOSIT DARI LIMBAH FINIR KAYU LAPIS BERDASARKAN UKURAN PARTIKEL DAN WAKTU PENGEMPAAN DENGAN MENGGUNAKAN PEREKAT LIMBAH PLASTIK POLIPROPILENA

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Alfonsus Rodriquez ◽  
Ahmad Yani ◽  
Fathul Yusro
Keyword(s):  
Particle Size ◽  
Physical And Mechanical Properties ◽  
Particle Sizes ◽  
Hot Press ◽  
Factor B ◽  
Pressing Time ◽  
Materials Used ◽  
Absorption Thickness ◽  
Water Contents

This study aims to analyze the quality of composite boards from plywood veneers waste and polypropylene plastic waste adhesives base on particle sizes, pressing times, and both of interaction towards physical and mechanical properties also to obtain the particle sizes and pressing time properly with the result that produce the qualified standard boards of JIS A 5908-2003. This research carried out at the wood workshop, laboratory of technology and processing of woods (the faculty of forestry, university of Tanjungpura), and the laboratory of PT. Duta Pertiwi Nusantara. The materials used in this study were plywood veneers waste and polypropylene plastic by 50% : 50% comparison. The research method was utilized the completely randomized factorial design by two treatment factors. Factor A was particle sizes that consisting of 6 mesh, 8 mesh, and 10 mesh. Factor B was pressing time that consisting of 10 minutes, 15 minute, and 20 minutes. Composite boards were created by 30 x 30 x 1 size in centimetres by means the density target was 0,7 gr/cm3. The pressing was done by hot press in 180oC temperature and composite boards conditioning for 14 days. The results of this study showed that the density, water absorption, thickness, Modulus of Repture (MOR), internal bonding, holding strength of screws in the composite boards have been qualified the standard of JIS A 5908-2003. While, the water contents and Modulus of Elasticity (MOE) testing were not qualified the standard of JIS 5908-2003. The treatment that produce the optimum composite boards which quality JIS A 5908-2003 standard was on the 8 mesh particle size treatment by means of 15 minutes pressing time.Keywords: Composite Board, Particle Size, Polypropylene Plastics, Pressing Time, Veneers Waste.

Sign in / Sign up

Export Citation Format

Share Document