scholarly journals Towards a better understanding of hot-mixed mortars for the conservation of historic buildings: the role of water temperature and steam during lime slaking

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Cecilia Pesce ◽  
Martha C. Godina ◽  
Alison Henry ◽  
Giovanni Pesce
Keyword(s):  
Water Temperature ◽  
Water Retention ◽  
Strength Properties ◽  
X Ray Diffraction ◽  
Mineralogical Characteristics ◽  
Slaked Lime ◽  
Lime Mortars ◽  
Restoration Work ◽  
Material Evidence

AbstractAccording to various historic accounts and material evidence, the practice of producing lime mortars by mixing the quicklime with the sand (i.e. hot-mixing) before first slaking it with water was much more common in the past centuries than appreciated by most contemporary academics, conservation professionals and craftsmen. However, in the last 10 years, there has been resurgence in interest in hot-mixing. In such systems, the steam developed during the mixing is supposed to be crucial in determining the superior characteristics of the mortars, but in-depth investigations on the role of steam in hot-mixing are very few. This study reports the results of some experimental work investigating the effects of water temperature and steam used for lime slaking on the characteristics of lime and related mortars. In these tests, calcic quicklime was slaked in water at 20 and 75 °C, and with steam at 90 °C. Microstructure and mineralogical characteristics of the hydrates were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Mortars produced with these limes were tested for fresh (water retention and flowability) and hardened (compressive and flexural strength) properties. Carbonation was assessed using SEM, XRD and phenolphthalein tests. Results show that steam-slaked lime is characterised by portlandite crystals with smaller crystallite size and significantly different microstructure compared to that of water-slaked lime. Results also show that mortars made with steam-slaked lime have higher water retention and flowability than the mortars produced with water-slaked lime. Under conditions of comparatively low relative humidity (c 40–50%), carbonation is slower in the steam-slaked lime mortar due to the lower water content compared to water-slaked lime mortars. Overall, these results confirm anecdotal reports of better workability and water retention and suggest that this production technology, which is only rarely used nowadays, can produce mortars with improved characteristics, and provide a means by which to match the performance of some historic mortars, and create compatible materials for conservation and restoration work.

Influence of the Aggregate Type on the Properties of Dolomitic Lime-Based Mortars

2016 ◽  
Vol 722 ◽  
pp. 343-350 ◽  
Author(s):  
Martin Vyšvařil ◽  
Tomáš Žižlavský ◽  
Patrik Bayer
Keyword(s):  
Positive Impact ◽  
Total Porosity ◽  
Strength Properties ◽  
Carbonation Reaction ◽  
Dolomitic Lime ◽  
Limestone Aggregate ◽  
Lime Mortars ◽  
Restoration Work ◽  
Limestone Fines

Considering the requirement of numerous restoration work on historical buildings with dolomitic lime-based mortars, a research of the applicability and suitability of various types of plasters for repairing the historical plasters have been developed. This work presents the applicability of limestone aggregate and limestone fines to dolomitic lime-based mortars. The role of aggregates on the properties of dolomitic lime mortars was examined by comparing pure quartz sand and limestone aggregate and its quantity in the mortar. Limestone aggregate and limestone fines accelerated the carbonation reaction in the mortars, but the positive impact of limestone aggregates to strength properties of mortars was not observed. Mortars with limestone aggregate showed higher total porosity and water absorption than those with quartz aggregate. Similar results was obtained for mortars with limestone fines. It was found that limestone aggregate and limestone fines, used in this work, is not so suitable and applicable to the dolomitic lime-based mortar as to the aerial lime-based mortars.

The Effect of Aggregate Type on the Properties of Lime Mortars

2016 ◽  
Vol 861 ◽  
pp. 141-148 ◽  
Author(s):  
Martin Vyšvařil ◽  
Tomáš Žižlavský ◽  
Patrik Bayer
Keyword(s):  
Mechanical Properties ◽  
Absorptive Capacity ◽  
Building Materials ◽  
Historical Buildings ◽  
Limestone Aggregate ◽  
Lime Mortars ◽  
Restoration Work ◽  
Limestone Fines ◽  
Dramatic Growth

Lime mortars represent indispensable building materials that have been used for centuries in civil engineering. Considering the necessity of numerous restoration work on historical buildings, a research of the applicability and suitability of various types of plasters for repairing the historical plasters has been developed. This work presents the applicability of limestone aggregate and limestone fines to aerial lime-based mortars. The role of aggregates on the properties of lime mortars is examined in this paper by comparing pure quartz sand and limestone aggregate and its quantity in the mortar. It was found that limestone aggregate produced the comparable or higher mortar strengths than quartz aggregate and slightly increased porosity, water absorptive capacity and carbonation rate of the mortars. Partially replacement of aggregate by limestone fines has caused dramatic growth in strength, especially in mortars with high content of binder. The applied limestone aggregate is convenient to lime-based mortars and the addition of limestone fines contributes to better mechanical properties of lime mortars.

SEM Study of Tension Wood Fiber Morphology and its Effect on Paper Properties

1977 ◽  
Vol 35 ◽  
pp. 308-309
Author(s):  
K. W. Robinson
Keyword(s):  
Tension Wood ◽  
Wood Fiber ◽  
Strength Properties ◽  
Fiber Morphology ◽  
Paper Properties ◽  
Pure Cellulose ◽  
Short Rotation ◽  
Hardwood Trees ◽  
Sem Study

Tension wood (TW) is an abnormal tissue of hardwood trees; although it has been isolated from most parts of the tree, it is frequently found on the upper side of branches and leaning stems. TW has been classically associated with geotropic alignment, but more recently it has been associated with fast growth. Paper made from TW is generally lower in strength properties. Consequently, the paper industries' growing dependence on fast growing, short- rotation trees will result in higher amounts of TW in the final product and a corresponding reduction in strength.Relatively few studies have dealt with the role of TW in the structure of paper. It was suggested that the lower strength properties of TW were due to a combination of factors, namely, its unique morphology, compression failures in the cell wall, and lower hemicellulose content. Central to the unique morphology of the TW fiber is the thick gelatinous layer (G-layer) composed almost entirely of pure cellulose.

A glimpse from the ancient world: What a gold necklace from Tillya-tepe reveals about opium in Afghanistan

Afghanistan ◽  
2020 ◽  
Vol 3 (2) ◽  
pp. 135-173
Author(s):  
Sara Peterson
Keyword(s):  
Opium Poppy ◽  
Ancient World ◽  
Cultural Importance ◽  
Large Seed ◽  
Potent Drug ◽  
Material Evidence ◽  
Societal Role

Among the six excavated burials at Tillya-tepe, in northern Afghanistan, was one occupied by an elite woman wearing a substantial necklace consisting of large gold beads shaped as seed-heads. The scale and fine workmanship of this necklace suggest that it was one of her most important possessions. It can be demonstrated that these large seed-heads are representations of poppy capsules, whose significance lies in the fact that they are the source of the potent drug opium. This necklace is the most outstanding object within a group of items decorated with poppy imagery, all of which were discovered in female burials. The opium poppy has long been a culturally important plant, and the implication of this identification is investigated in several contexts. Firstly, the proliferation of poppy imagery in the female burials at Tillya-tepe is examined, and then there is a discussion of material evidence for opium among relevant peoples along the Eurasian steppes. The particular cultural importance of opium is reviewed, leading finally to a proposal for the societal role of these women.

Role of the Structure and Electronic Properties of Fe2O3-MoO3 Catalyst on the Dehydration of Isopropyl Alcohol

1993 ◽  
Vol 58 (7) ◽  
pp. 1591-1599 ◽  
Author(s):  
Abd El-Aziz A. Said
Keyword(s):  
Active Sites ◽  
Isopropyl Alcohol ◽  
Oxide Catalyst ◽  
Flow System ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalyst Composition ◽  
Surface Active

Molybdenum oxide catalyst doped or mixed with (1 - 50) mole % Fe3+ ions were prepared. The structure of the original samples and the samples calcined at 400 °C were characterized using DTA, X-ray diffraction and IR spectra. Measurements of the electrical conductivity of calcined samples with and without isopropyl alcohol revealed that the conductance increases on increasing the content of Fe3+ ions up to 50 mole %. The activation energies of charge carriers were determined in presence and absence of the alcohol. The catalytic dehydration of isopropyl alcohol was carried out at 250 °C using a flow system. The results obtained showed that the doped or mixed catalysts are active and selective towards propene formation. However, the catalyst containing 40 mole % Fe3+ ions exhibited the highest activity and selectivity. Correlations were attempted to the catalyst composition with their electronic and catalytic properties. Probable mechanism for the dehydration process is proposed in terms of surface active sites.

scholarly journals Modeling of magneto-conductivity of bismuth selenide: a topological insulator

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Yogesh Kumar ◽  
Rabia Sultana ◽  
Prince Sharma ◽  
V. P. S. Awana
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Single Crystal ◽  
Single Crystals ◽  
X Ray Diffraction ◽  
Field Range ◽  
X Ray ◽  
Bulk Carriers ◽  
Different Temperatures

AbstractWe report the magneto-conductivity analysis of Bi2Se3 single crystal at different temperatures in a magnetic field range of ± 14 T. The single crystals are grown by the self-flux method and characterized through X-ray diffraction, Scanning Electron Microscopy, and Raman Spectroscopy. The single crystals show magnetoresistance (MR%) of around 380% at a magnetic field of 14 T and a temperature of 5 K. The Hikami–Larkin–Nagaoka (HLN) equation has been used to fit the magneto-conductivity (MC) data. However, the HLN fitted curve deviates at higher magnetic fields above 1 T, suggesting that the role of surface-driven conductivity suppresses with an increasing magnetic field. This article proposes a speculative model comprising of surface-driven HLN and added quantum diffusive and bulk carriers-driven classical terms. The model successfully explains the MC of the Bi2Se3 single crystal at various temperatures (5–200 K) and applied magnetic fields (up to 14 T).

scholarly journals Role of Biochar in Improving Sandy Soil Water Retention and Resilience to Drought

Water ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 407
Author(s):  
Ling Li ◽  
Yong-Jiang Zhang ◽  
Abigayl Novak ◽  
Yingchao Yang ◽  
Jinwu Wang
Keyword(s):  
Climate Variability ◽  
Sandy Soil ◽  
Water Retention ◽  
Sandy Soils ◽  
Crop Productivity ◽  
Future Research ◽  
Soil Water Retention ◽  
The World ◽  
Water Holding

In recent years, plants in sandy soils have been impacted by increased climate variability due to weak water holding and temperature buffering capacities of the parent material. The projected impact spreads all over the world, including New England, USA. Many regions of the world may experience an increase in frequency and severity of drought, which can be attributed to an increased variability in precipitation and enhanced water loss due to warming. The overall benefits of biochar in environmental management have been extensively investigated. This review aims to discuss the water holding capacity of biochar from the points of view of fluid mechanics and propose several prioritized future research topics. To understand the impacts of biochar on sandy soils in-depth, sandy soil properties (surface area, pore size, water properties, and characteristics) and how biochar could improve the soil quality as well as plant growth, development, and yield are reviewed. Incorporating biochar into sandy soils could result in a net increase in the surface area, a stronger hydrophobicity at a lower temperature, and an increase in the micropores to maximize gap spaces. The capability of biochar in reducing fertilizer drainage through increasing water retention can improve crop productivity and reduce the nutrient leaching rate in agricultural practices. To advance research in biochar products and address the impacts of increasing climate variability, future research may focus on the role of biochar in enhancing soil water retention, plant water use efficiency, crop resistance to drought, and crop productivity.

scholarly journals “Newton’s cradle” proton relay with amide–imidic acid tautomerization in inverting cellulase visualized by neutron crystallography

2015 ◽  
Vol 1 (7) ◽  
pp. e1500263 ◽  
Author(s):  
Akihiko Nakamura ◽  
Takuya Ishida ◽  
Katsuhiro Kusaka ◽  
Taro Yamada ◽  
Shinya Fushinobu ◽  
...  
Keyword(s):  
Glycoside Hydrolases ◽  
Side Chain ◽  
Enzymatic Reactions ◽  
X Ray Diffraction ◽  
Peptide Bonds ◽  
Proton Relay ◽  
Newton’S Cradle ◽  
Dynamics Simulations ◽  
Hydrolysis Of

Hydrolysis of carbohydrates is a major bioreaction in nature, catalyzed by glycoside hydrolases (GHs). We used neutron diffraction and high-resolution x-ray diffraction analyses to investigate the hydrogen bond network in inverting cellulase PcCel45A, which is an endoglucanase belonging to subfamily C of GH family 45, isolated from the basidiomycete Phanerochaete chrysosporium. Examination of the enzyme and enzyme-ligand structures indicates a key role of multiple tautomerizations of asparagine residues and peptide bonds, which are finally connected to the other catalytic residue via typical side-chain hydrogen bonds, in forming the “Newton’s cradle”–like proton relay pathway of the catalytic cycle. Amide–imidic acid tautomerization of asparagine has not been taken into account in recent molecular dynamics simulations of not only cellulases but also general enzyme catalysis, and it may be necessary to reconsider our interpretation of many enzymatic reactions.

scholarly journals Crystallization and X-ray diffraction data analysis of human deoxyhaemoglobin A0 fully stripped of any anions

1999 ◽  
Vol 55 (11) ◽  
pp. 1914-1916 ◽  
Author(s):  
F. A. V. Seixas ◽  
W. F. de Azevedo ◽  
M. F. Colombo
Keyword(s):  
Diffraction Data ◽  
Oxygen Affinity ◽  
X Ray Diffraction ◽  
Structural Explanation ◽  
Human Haemoglobin ◽  
X Ray ◽  
High Resolution Structure ◽  
Allosteric Properties

In this work, initial crystallographic studies of human haemoglobin (Hb) crystallized in isoionic and oxygen-free PEG solution are presented. Under these conditions, functional measurements of the O2-linked binding of water molecules and release of protons have evidenced that Hb assumes an unforeseen new allosteric conformation. The determination of the high-resolution structure of the crystal of human deoxy-Hb fully stripped of anions may provide a structural explanation for the role of anions in the allosteric properties of Hb and, particularly, for the influence of chloride on the Bohr effect, the mechanism by which Hb oxygen affinity is regulated by pH. X-ray diffraction data were collected to 1.87 Å resolution using a synchrotron-radiation source. Crystals belong to the space group P21212 and preliminary analysis revealed the presence of one tetramer in the asymmetric unit. The structure is currently being refined using maximum-likelihood protocols.

Sign in / Sign up

Export Citation Format

Share Document