Synthetic seismic sections of typical petroleum traps

Geophysics ◽  
1978 ◽  
Vol 43 (6) ◽  
pp. 1119-1147 ◽  
Author(s):  
Bruce T. May ◽  
Franta Hron
Keyword(s):  
Cross Sections ◽  
Structural Information ◽  
Mode Conversion ◽  
Three Dimensional ◽  
Fundamental Principle ◽  
Seismic Exploration ◽  
Complex Behavior ◽  
P Waves ◽  
Seismic Sections ◽  
Zero Offset

Interpretation of seismic reflections remains a key problem in seismic exploration because reflections have complex behavior, especially near geologic structures. One method to gain an understanding of this complex behavior is to study synthetic seismic sections of models of typical petroleum traps as computed by zero‐offset ray tracing for primary P‐waves only. These synthetic sections have features of significant interpretative value to the practicing geophysicist, such as variations in reflection amplitudes and complexities in reflection‐time geometries. Asymptotic ray theory was applied to calculate reflection amplitudes, accounting for mode conversion and three‐dimensional geometric divergence of ray tubes in the presence of curvilinear interfaces. This suite of synthetic seismic sections illustrates the difficulties in making correct seismic interpretations of geologic structures and suggests three conclusions: (1) The customary assumption that seismic sections are simple images of geologic cross‐sections is an oversimplification and can lead to erroneous interpretations. (2) Variations in overlying strata produce marked disturbances in reflection amplitude and traveltime. (3) Critical reflections that provide key structural information are often difficult to recognize and are apt to be ignored, or misidentified, especially if trace processing has been cursory. A fundamental principle of interpretation is underscored by this study: CDP stacked seismic sections must be interpreted so as to be consistent with structural depth models because stacked sections are not simple images of geologic structures.

Dependent Scattering of Acoustic Phonons From Particles Embedded in an Anisotropic Medium

2007 ◽  
Author(s):  
Neil Zuckerman ◽  
Jennifer R. Lukes
Keyword(s):  
Cross Sections ◽  
Phonon Scattering ◽  
Elastic Anisotropy ◽  
Mode Conversion ◽  
Three Dimensional ◽  
Atomic Scale ◽  
Dynamics Simulation ◽  
Nanometer Scale ◽  
Acoustic Phonons ◽  
Scale Granularity

Dependent scattering of acoustic phonons by multiple nanometer-scale inclusions in anisotropic media is investigated using a new molecular dynamics simulation technique. The spectral-directional characteristics of the scattering are found by calculation of three-dimensional scattering phase functions and cross sections for inclusions of varying sizes in various spatial arrangements. The technique enables computation of the effects of reflected wave interference and sequential scattering, mode conversion, lattice strain, elastic anisotropy, and atomic-scale granularity on acoustic phonon scattering from structured inclusions. The results will improve understanding and prediction of heat transfer in quantum-dot superlattices and other engineered thermal materials with nanometer-scale structures.

Two-Dimensional Crystallization of Tetanus Toxin

1985 ◽  
Vol 43 ◽  
pp. 528-529
Author(s):  
Jeffry A. Reidler ◽  
John P. Robinson
Keyword(s):  
Electron Microscopy ◽  
Tetanus Toxin ◽  
Structural Information ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Membrane Interface ◽  
3D Reconstructions ◽  
Cellular Receptors ◽  
Computer Reconstruction ◽  
2D Crystals

We have prepared two-dimensional (2D) crystals of tetanus toxin using procedures developed by Uzgiris and Kornberg for the directed production of 2D crystals of monoclonal antibodies at an antigen-phospholipid monolayer interface. The tetanus toxin crystals were formed using a small mole fraction of the natural receptor, GT1, incorporated into phosphatidyl choline monolayers. The crystals formed at low concentration overnight. Two dimensional crystals of this type are particularly useful for structure determination using electron microscopy and computer image refinement. Three dimensional (3D) structural information can be derived from these crystals by computer reconstruction of photographs of toxin crystals taken at different tilt angles. Such 3D reconstructions may help elucidate the mechanism of entry of the enzymatic subunit of toxins into cells, particularly since these crystals form directly on a membrane interface at similar concentrations of ganglioside GT1 to the natural cellular receptors.

EMCAT: An automatic image-processing system for electron-microscopic tomography

1994 ◽  
Vol 52 ◽  
pp. 418-419
Author(s):  
Weiping Liu ◽  
John W. Sedat ◽  
David A. Agard
Keyword(s):  
Image Processing ◽  
Structural Information ◽  
Imaging Technique ◽  
Three Dimensional ◽  
Processing System ◽  
Electron Microscopic ◽  
Data Set ◽  
Ordered Structures ◽  
Automatic Image Processing ◽  
Em Tomography

Any real world object is three-dimensional. The principle of tomography, which reconstructs the 3-D structure of an object from its 2-D projections of different view angles has found application in many disciplines. Electron Microscopic (EM) tomography on non-ordered structures (e.g., subcellular structures in biology and non-crystalline structures in material science) has been exercised sporadically in the last twenty years or so. As vital as is the 3-D structural information and with no existing alternative 3-D imaging technique to compete in its high resolution range, the technique to date remains the kingdom of a brave few. Its tedious tasks have been preventing it from being a routine tool. One keyword in promoting its popularity is automation: The data collection has been automated in our lab, which can routinely yield a data set of over 100 projections in the matter of a few hours. Now the image processing part is also automated. Such automations finish the job easier, faster and better.

Geological Field Sketches and Illustrations

2019 ◽  
Author(s):  
Matthew J. Genge
Keyword(s):  
Cross Sections ◽  
Earth Science ◽  
Three Dimensional ◽  
Worked Examples ◽  
Scientific Publications ◽  
Thin Sections ◽  
Geological Features ◽  
Different Types ◽  
The Subject

Drawings, illustrations, and field sketches play an important role in Earth Science since they are used to record field observations, develop interpretations, and communicate results in reports and scientific publications. Drawing geology in the field furthermore facilitates observation and maximizes the value of fieldwork. Every geologist, whether a student, academic, professional, or amateur enthusiast, will benefit from the ability to draw geological features accurately. This book describes how and what to draw in geology. Essential drawing techniques, together with practical advice in creating high quality diagrams, are described the opening chapters. How to draw different types of geology, including faults, folds, metamorphic rocks, sedimentary rocks, igneous rocks, and fossils, are the subjects of separate chapters, and include descriptions of what are the important features to draw and describe. Different types of sketch, such as drawings of three-dimensional outcrops, landscapes, thin-sections, and hand-specimens of rocks, crystals, and minerals, are discussed. The methods used to create technical diagrams such as geological maps and cross-sections are also covered. Finally, modern techniques in the acquisition and recording of field data, including photogrammetry and aerial surveys, and digital methods of illustration, are the subject of the final chapter of the book. Throughout, worked examples of field sketches and illustrations are provided as well as descriptions of the common mistakes to be avoided.

Pushing the Envelope

2018 ◽  
Author(s):  
Eaton E. Lattman ◽  
Thomas D. Grant ◽  
Edward H. Snell
Keyword(s):  
High Resolution ◽  
Electron Density ◽  
Structural Information ◽  
Hydration Shell ◽  
Three Dimensional ◽  
Scattering Data ◽  
Saxs Data ◽  
Electron Density Function ◽  
Angle Scattering ◽  
Iterative Structure

Direct electron density determination from SAXS data opens up new opportunities. The ability to model density at high resolution and the implicit direct estimation of solvent terms such as the hydration shell may enable high-resolution wide angle scattering data to be used to calculate density when combined with additional structural information. Other diffraction methods that do not measure three-dimensional intensities, such as fiber diffraction, may also be able to take advantage of iterative structure factor retrieval. While the ability to reconstruct electron density ab initio is a major breakthrough in the field of solution scattering, the potential of the technique has yet to be fully uncovered. Additional structural information from techniques such as crystallography, NMR, and electron microscopy and density modification procedures can now be integrated to perform advanced modeling of the electron density function at high resolution, pushing the boundaries of solution scattering further than ever before.

Nonrandom Segregation of the Mouse Univalent X Chromosome: Evidence of Spindle-Mediated Meiotic Drive

Genetics ◽  
2000 ◽  
Vol 156 (2) ◽  
pp. 775-783 ◽  
Author(s):  
Renée LeMaire-Adkins ◽  
Patricia A Hunt
Keyword(s):  
X Chromosome ◽  
Chromosome Abnormality ◽  
Three Dimensional ◽  
Fundamental Principle ◽  
Mendelian Inheritance ◽  
Segregation Behavior ◽  
Chromosome Transmission ◽  
Distortion Effect ◽  
Random Segregation ◽  
Transmission Distortion

Abstract A fundamental principle of Mendelian inheritance is random segregation of alleles to progeny; however, examples of distorted transmission either of specific alleles or of whole chromosomes have been described in a variety of species. In humans and mice, a distortion in chromosome transmission is often associated with a chromosome abnormality. One such example is the fertile XO female mouse. A transmission distortion effect that results in an excess of XX over XO daughters among the progeny of XO females has been recognized for nearly four decades. Utilizing contemporary methodology that combines immunofluorescence, FISH, and three-dimensional confocal microscopy, we have readdressed the meiotic segregation behavior of the single X chromosome in oocytes from XO females produced on two different inbred backgrounds. Our studies demonstrate that segregation of the univalent X chromosome at the first meiotic division is nonrandom, with preferential retention of the X chromosome in the oocyte in ∼60% of cells. We propose that this deviation from Mendelian expectations is facilitated by a spindle-mediated mechanism. This mechanism, which appears to be a general feature of the female meiotic process, has implications for the frequency of nondisjunction in our species.

scholarly journals Thermo-Hydraulic Performance of U-Tube Borehole Heat Exchanger with Different Cross-Sections

2021 ◽  
Vol 13 (6) ◽  
pp. 3255
Author(s):  
Aizhao Zhou ◽  
Xianwen Huang ◽  
Wei Wang ◽  
Pengming Jiang ◽  
Xinwei Li
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Heat Resistance ◽  
Cross Sections ◽  
Three Dimensional ◽  
Thermal Response ◽  
Transfer Efficiency ◽  
Cross Sectional ◽  
Heat Transfer Efficiency ◽  
Oval Tube

For reducing the initial GSHP investment, the heat transfer efficiency of the borehole heat exchange (BHE) system can be enhanced to reduce the number or depth of drilling. This paper proposes a novel and simple BHE design by changing the cross-sectional shape of the U-tube to increase the heat transfer efficiency of BHEs. Specifically, in this study, we (1) verified the reliability of the three-dimensional numerical model based on the thermal response test (TRT) and (2) compared the inlet and outlet temperatures of the different U-tubes at 48 h under the premise of constant leg distance and fluid area. Referent to the circular tube, the increases in the heat exchange efficiencies of the curved oval tube, flat oval tube, semicircle tube, and sector tube were 13.0%, 19.1%, 9.4%, and 14.8%, respectively. (3) The heat flux heterogeneity of the tubes on the inlet and outlet sides of the BHE, in decreasing order, is flat oval, semicircle, curved oval, sector, and circle shapes. (4) The temperature heterogeneity of the borehole wall in the BHE in decreasing order is circle, sector, curved oval, flat oval, and semicircle shapes. (5) Under the premise of maximum leg distance, referent to the heat resistance of the tube with a circle shape at 48 h, the heat exchange efficiency of the curved oval, flat oval, semicircle, and sector tubes increased 12.6%, 17.7%, 10.3%, and 7.8%, respectively. (6) We found that the adjustments of the leg distance and the tube shape affect the heat resistance by about 25% and 12%, respectively. (7) The flat-oval-shaped tube at the maximum leg distance was found to be the best tube design for BHEs.

scholarly journals Computer-aided design of multi-purpose steel headframes for mines with a new technical level

2020 ◽  
Vol 174 ◽  
pp. 01048
Author(s):  
Elena Kassikhina ◽  
Vladimir Pershin ◽  
Nina Rusakova
Keyword(s):  
Cross Sections ◽  
Computer Aided Design ◽  
Information Technologies ◽  
Three Dimensional ◽  
Numerical Control ◽  
Technical Level ◽  
Resource Saving ◽  
Existing Structures ◽  
Set Up ◽  
Aided Design

The existing structures of the steel sinking headgear and permanent headframe do not meet the requirements of resource saving (metal consumption and manpower input at installation), and the present methods of the headframe designing do not fully reflect recent possibilities of applying of the advanced information technologies. Technical level of the modern software makes it possible for designers to set up multiple numerical experiments to create a computer simulation that allows solving the problem without field and laboratory experiments, and therefore without special costs. In this regard, a mathematical simulation has been developed and based on it, software to select cross-sections of multi- purpose steel headframe elements and to calculate proper weight of its metal structures depending on the characteristics and hoisting equipment. A headframe drawing is displayed, as the results of the software work, including list of elements, obtained optimal hoisting equipment in accordance with the initial data. The software allows speeding up graphic work and reducing manpower input on calculations and paper work. The software allows developing a three-dimensional image of the structure and its functional blocks, based on the obtained initial parameters, as well as developing control software for units with numerical control (NC) in order to manufacture multi-purpose headframes.

Sign in / Sign up

Export Citation Format

Share Document