Fragility Analysis of Reinforced Masonry Shear Walls

2012 ◽  
Vol 28 (4) ◽  
pp. 1523-1547 ◽  
Author(s):  
Juan Murcia-Delso ◽  
P. Benson Shing
Keyword(s):  
Shear Walls ◽  
Fragility Functions ◽  
Damage State ◽  
Shear Damage ◽  
Drift Ratio ◽  
Reinforced Masonry ◽  
Specific Loading ◽  
Story Drift ◽  
Damage States ◽  
Story Building

Fragility functions have been developed to evaluate the damageability of fully grouted and partially grouted reinforced masonry shear walls subjected to in-plane seismic loading. Six damage states are considered, representing different levels of flexure, diagonal shear, and sliding shear damage. For each damage state, two classes of fragility functions have been developed. One has the story-drift ratio as the demand parameter. The other uses normalized demand parameters that account for the specific loading condition and design details of a wall component. All the fragility functions are derived from experimental data except for those developed for partially grouted walls and the sliding shear damage state. With both classes of fragility functions, the seismic damageability of flexure-dominated cantilever reinforced masonry shear walls in a four-story building has been assessed. It has been shown that the normalized flexural demand parameter provides a better correlation to the degree of damage developed in a wall than the story-drift ratio.

Fragility Functions for Steel Plate Shear Walls

2012 ◽  
Vol 28 (2) ◽  
pp. 405-426 ◽  
Author(s):  
Nicole M. Baldvins ◽  
Jeffery W. Berman ◽  
Laura N. Lowes ◽  
Todd M. Janes ◽  
Natalie A. Low
Keyword(s):  
Steel Plate ◽  
Probability Distributions ◽  
Experimental Studies ◽  
Shear Walls ◽  
Fragility Functions ◽  
Empirical Relationships ◽  
Steel Plate Shear Walls ◽  
Story Drift ◽  
Damage States ◽  
Lognormal Probability

Fragility functions are developed to predict the method of repair required for steel plate shear walls damaged due to earthquake loading. The results of previous experimental studies are used to develop empirical relationships between damage states and story drift. Damage states are proposed and linked deterministically with commonly employed methods of repair; these damage states are characterized by parameters such as yielding and tearing of the steel plate and yielding, buckling and fracture of frame members. Lognormal probability distributions are fit to the empirical data and evaluated using standard statistical methods. The results of this effort are families of fragility functions that predict the required method of repair for a damaged wall.

scholarly journals Response analysis of a multi-story building structure with a variety of horizontal irregularities and shear wall geometries

2021 ◽  
Vol 933 (1) ◽  
pp. 012008
Author(s):  
A H Prathama ◽  
M Teguh ◽  
F Saleh
Keyword(s):  
Urban Areas ◽  
Response Spectrum ◽  
Structural Models ◽  
Shear Walls ◽  
Shear Wall ◽  
Response Analysis ◽  
Base Shear ◽  
Drift Ratio ◽  
Story Drift ◽  
Story Building

Abstract The growing growth of human activities has led to changes in housing patterns in urban areas. The land crisis in urban areas has made land prices uneconomical, so buildings are designed vertically. One solution to resist earthquakes in multi-story buildings is to add a shear wall structure with the proper profile and layout. Shear wall designs with variations influence the base shear, drift ratio, lateral deflection, and story drift patterns. This study presents the structural response comparison of buildings against variations in the profile and layout of shear walls subjected to earthquake loads. Force Based Design method utilizing the response spectrum approach was adopted in the analysis and carried out using SAP200. Six structural models comprise a frame without shear walls, three L-profile shear walls, two I-profile (straight) shear walls. The simulation results of the overall structural models show that the profile and layout configuration of shear walls in the frame structure of a multi-story building correlates directly to the performance of base shear, drift ratio, and story drift with relatively comparative conditions.

Multivariate Fragility Models for Earthquake Engineering

2016 ◽  
Vol 32 (1) ◽  
pp. 441-461 ◽  
Author(s):  
Abbas Javaherian Yazdi ◽  
Terje Haukaas ◽  
Tony Yang ◽  
Paolo Gardoni
Keyword(s):  
Logistic Regression ◽  
Earthquake Engineering ◽  
Shear Walls ◽  
Performance Assessments ◽  
Fragility Functions ◽  
Structural Components ◽  
Logistic Regression Models ◽  
Damage Models ◽  
Damage States ◽  
Performance Based Earthquake Engineering

This paper employs a logistic regression technique to develop multivariate damage models. The models are intended for performance assessments that require the probability that structural components are in one of several damage states. As such, the developments represent an extension of the univariate fragility functions that are omnipresent in contemporary performance-based earthquake engineering. The multivariate logistic regression models that are put forward here eliminate several of the limitations of univariate fragility functions. Furthermore, the new models are readily substituted for existing fragility functions without any modifications to the existing performance-based analysis methodologies. To demonstrate the proposed modeling approach, a large number of tests of reinforced concrete shear walls are employed to develop multivariate damage models. It is observed that the drift ratio and aspect ratio of concrete shear walls are among the parameters that are most influential on the damage probabilities.

scholarly journals Seismic and Wind Analysis of RCC Building with Different Shape of Shear Wall and Without Shear Wall

2022 ◽  
Vol 10 (1) ◽  
pp. 678-683
Author(s):  
Bayi Bage
Keyword(s):  
Seismic Analysis ◽  
Three Dimensional ◽  
Shear Walls ◽  
Shear Wall ◽  
Structure Comparison ◽  
Displacement Capacity ◽  
Irregular Shapes ◽  
Strength Capacity ◽  
Story Drift ◽  
Story Building

Abstract: ETABS Stand for Extended Three-Dimensional Analysis of Building systems. ETABS integrates every aspect of the engineering design process. In the present situations of construction industry, the buildings that are being constructed are gaining significance, in general those with the best possible outcomes which are referred to members like beams and columns in multi storeys R.C structures. This paper deals with the seismic analysis of regular B+G+26 story building with shear wall and G+B+10 Story building with different irregular shapes considering different shapes of shear wall at different locations has been carried out. Which can be done in ETABS taking all the considerations regarding codes and other factors into account. All the buildings were analyzed with the same method as stated in IS 1893-Part-1:2016. The effect of shear walls on lateral capacity of the building are examined because the seismic analysis of a frame depends upon the location and symmetry of shear wall. Present study shows the shear wall improves not only the lateral stiffness and strength capacity but also the displacement capacity of structure. Comparison of results been done of different models by comparing the parameters such as story drift, story displacement, story stiffness and base reaction. Therefore, as far as possible irregularities in a building must be avoided. But, if irregularities have to be introduced for any reason, they must be designed properly following the conditions of IS 13920:1993. The complex shaped buildings are now days getting popular, but they carry a risk of sustaining damages during earthquakes. Keywords ETABS Software; IS Code 1892-Part-1:2016; IS Code 13920:1993; IS Code 875-Part-1 and Part-2

scholarly journals Experimental Investigation into the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls with Vertical Joint Connections

2021 ◽  
Vol 11 (10) ◽  
pp. 4421
Author(s):  
Zhiming Zhang ◽  
Fenglai Wang
Keyword(s):  
Seismic Performance ◽  
Cross Sections ◽  
Shear Walls ◽  
Construction Method ◽  
Shear Capacity ◽  
Initial Stiffness ◽  
Equivalent Viscous Damping ◽  
Displacement Ductility ◽  
Reinforced Masonry ◽  
Cracking Performance

In this study, four single-story reinforced masonry shear walls (RMSWs) (two prefabricated and two cast-in-place) under reversed cyclic loading were tested to evaluate their seismic performance. The aim of the study was to evaluate the shear behavior of RMSWs with flanges at the wall ends as well as the effect of construction method. The test results showed that all specimens had a similar failure mode with diagonal cracking. However, the crack distribution was strongly influenced by the construction method. The lateral capacity of the prefabricated walls was 12% and 27% higher than that of the corresponding cast-in-place walls with respect to the rectangular and T-shaped cross sections. The prefabricated walls showed better post-cracking performance than did the cast-in-place wall. The secant stiffness of all the walls decreased rapidly to approximately 63% of the initial stiffness when the first major diagonal crack was observed. The idealized equivalent elastic-plastic system showed that the prefabricated walls had a greater displacement ductility of 3.2–4.8 than that of the cast-in-place walls with a displacement ductility value of 2.3–2.7. This proved that the vertical joints in prefabricated RMSWs enhanced the seismic performance of walls in shear capacity and ductility. In addition, the equivalent viscous damping of the specimens ranged from 0.13 to 0.26 for prefabricated and cast-in-place walls, respectively.

scholarly journals In-plane shear strength and damage fragility functions for partially-grouted reinforced masonry walls with bond-beam reinforcement

2021 ◽  
Vol 242 ◽  
pp. 112569
Author(s):  
Zhiming Zhang ◽  
Juan Murcia-Delso ◽  
Cristián Sandoval ◽  
Gerardo Araya-Letelier ◽  
Fenglai Wang
Keyword(s):  
Shear Strength ◽  
Masonry Walls ◽  
Fragility Functions ◽  
Plane Shear ◽  
Reinforced Masonry

The Lima earthquake of October 3, 1974: Damage distribution

1977 ◽  
Vol 67 (5) ◽  
pp. 1441-1472
Author(s):  
R. Husid ◽  
A. F. Espinosa ◽  
J. de las Casas
Keyword(s):  
Reinforced Concrete ◽  
Structural Damage ◽  
Concrete Structures ◽  
Effective Length ◽  
Reinforced Concrete Structures ◽  
Severe Damage ◽  
Original Design ◽  
Reinforced Masonry ◽  
Water Tanks ◽  
Story Building

abstract The October 3, 1974, earthquake caused severe damage to buildings of adobe and quincha construction, and also to masonry, reinforced masonry, and reinforced-concrete structures in Lima and vicinity. Most of the damage to well-built structures was due, in part, to the lack of lateral resistance in the original design and to the fact that this earthquake had more energy around 0.4 seconds period than prior destructive earthquakes. Water tanks on the roofs of structures with four or five stories were damaged. Well-engineered single-story buildings were less affected than taller structures. Considerable structural damage to reinforced-concrete structures occurred in the districts of Barranco, La Campiña Molina, and Callao. In La Campiña three-story building partly collapsed and other buildings sustained considerable damage. In La Molina, the buildings of the Agrarian University sustained severe damage, and some collapsed. In Surco, the district adjacent to La Molina, there was no appreciable damage. In Callao, a four-story building collapsed, and the upper half of a concrete silo collapsed. In reinforced-concrete structures, column ties were frequently small in diameter, widely spaced, and not well connected. Usually, the reinforcement of resisting elements had no relation to their stiffnesses. Front columns in school buildings were restrained by high brick walls and had rather short effective lengths to allow building displacement in that direction. The windows in the rear walls gave the rear columns a much greater effective length. Therefore, a longitudinal displacement induces large shear forces in the front columns where most of the severe damage occurred. This problem was not considered in the design of these structures.

scholarly journals Analisis Pengaruh Lokasi Dinding Geser Terhadap Pergeseran Lateral Bangunan Bertingkat Beton Bertulang 5 Lantai

2021 ◽  
Vol 4 (1) ◽  
pp. 16
Author(s):  
Leonardus Setia Budi Wibowo ◽  
Dermawan Zebua
Keyword(s):  
Lateral Displacement ◽  
Shear Walls ◽  
Seismic Loading ◽  
Shear Wall ◽  
Structural System ◽  
Earthquake Force ◽  
Earthquake Resistant ◽  
Story Drift ◽  
Frame System ◽  
Rc Shear Wall

Indonesia is one of the countries in the earthquake region. Therefore, it is necessary to build earthquake-resistant buildings to reduce the risk of material and life losses. Reinforced Concrete (RC) shear walls is one of effective structure element to resist earthquake forces. Applying RC shear wall can effectively reduce the displacement and story-drift of the structure. This research aims to study the effect of shear wall location in symmetric medium-rise building due to seismic loading. The symmetric medium rise-building is analyzed for earthquake force by considering two types of structural system. i.e. Frame system and Dual system. First model is open frame structural system and other three models are dual type structural system. The frame with shear walls at core and centrally placed at exterior frames showed significant reduction more than 80% lateral displacement at the top of structure.

Sign in / Sign up

Export Citation Format

Share Document