A numerical study on soot formation and oxidation for a direct injection diesel engine

2003 ◽  
Vol 217 (5) ◽  
pp. 403-413 ◽  
Author(s):  
N Sung ◽  
S Lee ◽  
H Kim ◽  
B Kim
Keyword(s):  
Diesel Engine ◽  
Combustion Temperature ◽  
Soot Formation ◽  
Direct Injection ◽  
Soot Oxidation ◽  
Operating Conditions ◽  
Injection Timing ◽  
Mixture Ratio ◽  
Soot Particles ◽  
Carbon Radicals

A numerical cycle model is developed to investigate the soot production in a direct injection (DI) diesel engine. The Surovikin and Fusco models for soot formation and the Nagle model for soot oxidation are used with the KIVA-3V code. In the Surovikin model, carbon radicals are produced from pyrolysis of fuel and soot particles grow through collisions with fuel molecules. In the Fusco model, the carbon radicals and acetylene are formed from pyrolysis of fuel. There, acetylene works for the growth of soot particles. From investigation of the e. ects of the operating conditions on soot formation and oxidation, it is found that soot formation is mainly governed by fuel concentration and combustion temperature and soot oxidation is more dependent on combustion temperature. The air-fuel ratio a. ects soot formation more than injection timing. For a stoichiometric mixture ratio, soot formation is increased because of the high combustion temperature.

Application of a Phenomenological Soot Model for Diesel Engine Combustion

2008 ◽  
Author(s):  
Xiaobei Cheng ◽  
Hongling Jv ◽  
Yifeng Wu
Keyword(s):  
Diesel Engine ◽  
Chemical Reactions ◽  
Oxidation Rate ◽  
Soot Formation ◽  
Soot Oxidation ◽  
Soot Concentration ◽  
Engine Operation ◽  
Soot Particles ◽  
Turbulent Eddies ◽  
Soot Model

The application of the improved CFD code for the simulation of combustion and emission formation in a high-speed diesel engine has been presented and discussed. The soot concentration transport equation is found and solved together with all other flow equations. A slip correction factor is introduced into this equation. In turbulent combustion, the soot particles are contained within the turbulent eddies, and burnt up swiftly with the dissipation of these eddies in the soot oxidation zone. However, the chemical reactions always process except the dissipation of turbulent eddies and the intermixing of soot particles and turbulent eddies. The soot oxidation rate should be controlled simultaneity by the chemical reactions rate and the dissipation rate of turbulent eddies. A hybrid particle turbulent transport controlled rate and soot oxidation rate model is present in this paper and Soot formation and oxidation processes have been modeled according to this model. A reasonable agreement of the measured and computed data of in-cylinder pressure, soot, and NO emissions for different engine operation conditions has been made. The precision of simulated soot concentration is improved compare with the commonly Hiroyasu—Nagel—Strickland (HNS) soot model.

Low-sooting combustion in a small-bore high-speed direct-injection diesel engine using narrow-angle injectors

2008 ◽  
Vol 222 (10) ◽  
pp. 1927-1937 ◽  
Author(s):  
T-G Fang ◽  
R E Coverdill ◽  
C-F F Lee ◽  
R A White
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Fuel Efficiency ◽  
Operating Conditions ◽  
Injection Timing ◽  
Exhaust Pipe ◽  
Injection Angle ◽  
Direct Injection Diesel Engine ◽  
Combustion Flame

An optically accessible high-speed direct-injection diesel engine was used to study the effects of injection angles on low-sooting combustion. A digital high-speed camera was employed to capture the entire cycle combustion and spray evolution processes under seven operating conditions including post-top-dead centre (TDC) injection and pre-TDC injection strategies. The nitrogen oxide (NO x) emissions were also measured in the exhaust pipe. In-cylinder pressure data and heat release rate calculations were conducted. All the cases show premixed combustion features. For post-TDC injection cases, a large amount of fuel deposition is seen for a narrower-injection-angle tip, i.e. the 70° tip, and ignition is observed near the injector tip in the centre of the bowl, while for a wider-injection-angle tip, namely a 110° tip, ignition occurs near the spray tip in the vicinity of the bowl wall. The combustion flame is near the bowl wall and at the central region of the bowl for the 70° tip. However, the flame is more distributed and centralized for the 110° tip. Longer spray penetration is found for the pre-TDC injection timing cases. Liquid fuel impinges on the bowl wall or on the piston top and a fuel film is formed. Ignition for all the pre-TDC injection cases occur in a distributed way in the piston bowl. Two different combustion modes are observed for the pre-TDC injection cases including a homogeneous bulky combustion flame at earlier crank angles and a heterogeneous film combustion mode with luminous sooting flame at later crank angles. In terms of soot emissions, NO x emissions, and fuel efficiency, results show that the late post-TDC injection strategy gives the best performance.

Understanding the soot reduction associated with injection timing variation in a small-bore diesel engine

2019 ◽  
pp. 146808741986805 ◽  
Author(s):  
Lingzhe Rao ◽  
Yilong Zhang ◽  
Sanghoon Kook ◽  
Kenneth S Kim ◽  
Chol-Bum Kweon
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Soot Formation ◽  
Soot Oxidation ◽  
Laser Induced Fluorescence ◽  
Injection Timing ◽  
Gas Temperature ◽  
Planar Laser ◽  
Laser Induced Incandescence ◽  
Ambient Gas

This study shows the in-cylinder soot reduction mechanism associated with injection timing variation in a small-bore optical diesel engine. For the three selected injection timings, three optical-/laser-based imaging diagnostics were performed to show the development of high-temperature reaction and soot within the cylinder, which include OH* chemiluminescence, planar laser–induced fluorescence of hydroxyl and planar laser–induced incandescence. In addition, detailed soot morphology analysis was conducted using thermophoresis-based soot particle sampling from two locations within the piston bowl, and the subsequent analysis of transmission electron microscope (TEM) images of the sampled soot aggregates was also conducted. The results suggest that when fuel injection timing is varied, ambient gas temperature makes a predominant effect on soot formation and oxidation. This is primarily combustion phasing effect as the advanced fuel injection moved the start of combustion closer to the top dead centre, and therefore, soot formation and oxidation occurred at elevated ambient gas temperature. There was an overall development pattern of in-cylinder soot consistently found for three injection timings of this study. The planar laser–induced incandescence images showed that a few small soot pockets first appear around the jet axis, which promptly grow into large soot regions behind the head of the flame marked planar laser–induced fluorescence of hydroxyl. The soot signals disappear due to significant oxidation induced by surrounding OH radicals. When the injection timing is advanced, the soot formation becomes higher as indicated by higher total laser–induced incandescence coverage, increased sampled particle counts and larger and more stretched soot aggregate structures. However, soot oxidation is also enhanced under this elevated ambient temperature environment. At the most advanced injection timing of this study, the enhanced soot oxidation outperformed the increased soot formation with both peak laser–induced incandescence signal coverage and late-cycle coverage showing lower values than those of more retarded injection timings.

Modelling for investigation of combustion and emission characteristics in a high-speed direct-injection diesel engine with light duty under various operating conditions

2008 ◽  
Vol 222 (11) ◽  
pp. 2159-2170 ◽  
Author(s):  
H J Kim ◽  
B W Ryu ◽  
C S Lee
Keyword(s):  
High Speed ◽  
Soot Formation ◽  
Numerical Study ◽  
Direct Injection ◽  
Operating Conditions ◽  
Injection System ◽  
Combustion Model ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Fuel Mass

A numerical study was conducted to investigate combustion and emission characteristics in a high-speed direct-injection engine with a common-rail injection system under various operating conditions. In order to analyse the combustion characteristics, several models were used in this study. They were the renormalization group k– ε model, the hybrid Kelvin—Helmholtz (wave) and the Rayleigh—Taylor model, the shell auto-ignition model, and the laminar and turbulent characteristic timescale combustion model. The prediction of exhaust emissions was conducted using nitrogen oxide NO x formation with an extended Zel'dovich mechanism and Hiroyasu soot formation with the Nagle—Strickland-Constable oxidation model respectively. Experimental combustion and emission characteristics were compared with calculated results under various operating conditions, such as injection timing, injection pressure, fuel mass, and engine speed. The calculated results show similar patterns to the experimental results in the cylinder pressure and the rate of heat release. In the emissions characteristics, NO x emission decreased as injection timing was retarded and the NO x and soot amounts increased with the increase in the injected fuel mass. The calculated soot trends for various injection timings showed different patterns from the experimental trends as the injection timing were retarded.

scholarly journals EFFECT OF OPERATING CONDITIONS ON PERFORMANCE AND EMISSIONS OF A DIESEL ENGINE OPERATED WITH DIESEL-HYDROGEN BLEND

2019 ◽  
Vol 19 (4) ◽  
pp. 337-357
Author(s):  
Haroun A.K. Shahad ◽  
Emad D. Abood
Keyword(s):  
Diesel Engine ◽  
Air Temperature ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Heating System ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emissions

Hydrogen is a clean fuel for internal combustion engines since it produces only water vapor and nitrogen oxides when it burns. In this research, hydrogen is used as a blending fuel with diesel to reduce pollutants emission and to improve performance. It is inducted in the inlet manifold, of a single cylinder, four stroke, direct injection, water cold diesel engine, type (Kirloskar). Hydrogen blending is done on energy replacement basis. A special electronic unit is designed and fabricated to control hydrogen blending ratio. The maximum achieved ratio is 30% of input energy and beyond that engine operation becomes unsatisfactory when the air temperature is 20 oC and injection timing of -35o CA which represent the first part of this work. Inlet air heating system is built and added in the experimental work. The heating system allows to increase the air temperature up to 100 oC. A heating of air to 60 oC with injection timing of -30o CA and 55% of hydrogen blending is executed in the second part of this study. Tests are done with 17.5 compression ratio and 1500 rpm. The brake specific fuel consumption is reduced by 29% and 46%, the engine thermal efficiency is increased with 16% and 21% for the 1st and 2nd part respectively. The pollutant emissions of carbon oxides, UHC, and smoke opacity are dramatically decreased by 19.5%, 13%, and 45% respectively for the 1st part and 41%, 38% and 65.6% for the 2nd part while NOx emission is increased by 10% and 25% for the 1st and 2nd part respectively.

Thermodynamics in a turbocharged direct injection diesel engine

1998 ◽  
Vol 212 (1) ◽  
pp. 11-24 ◽  
Author(s):  
S H Chan
Keyword(s):  
Diesel Engine ◽  
Thermodynamic Properties ◽  
Fuel Injection ◽  
Direct Injection ◽  
Equilibrium Constants ◽  
Thermodynamic Cycle ◽  
Operating Conditions ◽  
Injection Timing ◽  
Algebraic Equations ◽  
Direct Injection Diesel Engine

Software has been developed for the calculation of the thermodynamic cycle and the entropy changes in a turbocharged, direct injection, diesel engine based upon the measured cylinder pressure and a shaft encoder output. Assumptions of homogeneous mixture and equilibrium thermodynamic properties are made for the products of combustion and the temporal variation in the fluid thermodynamic state is followed in a quasi-steady manner through a series of adjacent equilibrium states, each separated by finite intervals of one degree crank angle (1°CA). The thermodynamic properties are calculated by either of two equivalent formulations — equilibrium constants or minimization of Gibbs free energy, and are expressed in algebraic equations for the partial derivative of internal energy and gas constant with respect to temperature, pressure and equivalence ratio. The effect of the engine operating conditions on the thermodynamic cycle is studied. Results show that the dynamic fuel injection timing and hence the ignition delay are strongly influenced by the operating conditions, and this explains the reasons for incorporating a fuel injection control system in modern vehicular engines for the optimization of the engine combustion cycle.

scholarly journals Effects of pilot injection timing and EGR on a modern V6 common rail direct injection diesel engine

2013 ◽  
Vol 50 ◽  
pp. 012008 ◽  
Author(s):  
Nik Rosli Abdullah ◽  
Rizalman Mamat ◽  
Miroslaw L Wyszynski ◽  
Anthanasios Tsolakis ◽  
Hongming Xu
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Common Rail ◽  
Injection Timing ◽  
Pilot Injection ◽  
Direct Injection Diesel Engine

Predicted Paths of Soot Particles in the Cylinders of a Direct Injection Diesel Engine

2012 ◽  
Author(s):  
Wan Mohd Faizal Wan Mahmood ◽  
Antonino LaRocca ◽  
Paul J. Shayler ◽  
Fabrizio Bonatesta ◽  
Ian Pegg
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Soot Particles ◽  
Direct Injection Diesel Engine

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Sign in / Sign up

Export Citation Format

Share Document