Overall and Stage Characteristics of Axial-flow Compressors

1950 ◽  
Vol 163 (1) ◽  
pp. 235-248 ◽  
Author(s):  
A. R. Howell ◽  
R. P. Bonham
Keyword(s):  
Axial Flow ◽  
Maximum Efficiency ◽  
Working Fluid ◽  
Test Results ◽  
Analytical Treatment ◽  
Axial Compressors ◽  
Simplified Method ◽  
Mass Flows ◽  
The Individual ◽  
Lengthy Process

Axial compressors, particularly near design conditions are, on the whole, amenable to analytical treatment, and usually a good estimate of their performance can be made before they are run. Away from the design points, the performances are conveniently thought of in terms of the overall characteristics of pressure-rises, temperature-rises, and efficiencies plotted against mass-flows. For these performance estimations the aerodynamicists must have knowledge of the stage and overall characteristics of previous compressors and of methods of predicting such characteristics. Obtaining the overall characteristics from a stage-by-stage calculation is a lengthy process, but, fortunately, simplified methods can often be used. In this lecture we have indicated some of the methods that are employed to obtain and predict the overall characteristics and their associated stage characteristics. Reference is made to test-results from various National Gas Turbine Establishment research compressors, one of which uses water instead of air as the working fluid, and also to published information on other compressors. The importance of blade and test errors on performance and analysis work is also emphasized. In our simplified method of analysis and prediction of overall characteristics we have reduced the individual overall characteristics at each speed to what are, in effect, mean stage characteristics plotted relative to their maximum-efficiency-point conditions. Then the maximum-efficiency-point conditions at the different speeds are plotted and considered separately.

scholarly journals Problems with Tribological Testings of Marketable Oils Using Laboratory Model Test Rigs

2018 ◽  
Vol 26 (42) ◽  
pp. 35-46
Author(s):  
Jürgen Rigo ◽  
Pavel Kovačócy
Keyword(s):  
Dynamic Testing ◽  
Test Methods ◽  
Working Fluid ◽  
Laboratory Model ◽  
Test Results ◽  
Engine Oils ◽  
Gear Oil ◽  
The One ◽  
The Individual ◽  
Laboratory Model Test

Abstract An important point in Tribology is mechanical-dynamic testing of lubricants and materials under stress and the interpretation of the results obtained therefrom. Widely-used test methods are often applied to test the performance of lubricants e.g. test results determined by tribometers should be treated carefully when using marketable oils. A closer evaluation of these results is part of this research paper. Within this study, several marketable oils were used and experimentally investigated. These were a gear oil, two engine oils, one hydraulic oil, one metal working fluid and one forming oil. There were several distinct differences. On the one hand, the used oils differ significantly in terms of their performance in the individual test methods. This is not surprising but has a clear reason in the different compositions of the lubricants resulting from their respective application. By subjecting these oils to diverse test methods with different test equipment, the results can vary widely and result in completely dissimilar results from the tests. Thus, a metalworking oil appears excellently when determining the welding force in the four-ball apparatus. In the high frequency liear oscillation tester, on the other hand, barely usable results are generated. Thus, there are two contradictory statements that should be the same.

Investigation on the Effects of Various Swirl Generators on Heat Transfer and Fluid Flow in Decaying Swirling Flows

2010 ◽  
Vol 224 (10) ◽  
pp. 2181-2197
Author(s):  
M Ahmadvand ◽  
A F Najafi ◽  
S Shahidinejad
Keyword(s):  
Heat Transfer ◽  
Swirling Flow ◽  
Flow Characteristics ◽  
Axial Flow ◽  
Working Fluid ◽  
Uniform Heat Flux ◽  
Mean Flow ◽  
Inlet Conditions ◽  
The Individual ◽  
Comparison Of The Results

Influences of three typical vortex generators on flow pattern and ensuing heat transfer augmentation were investigated and compared at similar Re and swirl numbers inlet conditions. Studied swirlers such as propeller swirlers, jet-type swirlers, and rotating honeycombs were installed at the pipe inlet. Reynolds number ranges from 10000 to 30000. Swirlers were set on the swirl numbers 1.4, 0.89, and 0.52, which were obtained by propellers. This study has been carried out under uniform heat flux condition and air was employed as the working fluid. The obtained results provide the individual effects of each swirler configuration on mean flow and turbulence distribution as well as on enhancement of heat transfer. Considering S=1.4, jet-type swirlers pointed 133 per cent Nu enhancement compared to axial flow, whereas propellers and rotating honeycombs approached 105 per cent and 79 per cent, respectively. For S=0.89, relative treatment has been changed and propellers with 70 per cent Nu augmentation demonstrated tip-top performance behind of which other swirlers lined. By decreasing the swirl number, approximately closer heat performances were represented from all swirler configurations. Comparison of the results of various swirlers exhibited that Re and swirl numbers are not generally sufficient to determine the swirling flow characteristics and each swirler confirms an individual flow quality.

scholarly journals Sensitivity Analysis of OTEC-CC-MX-1 kWe Plant Prototype

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2585
Author(s):  
Jessica Guadalupe Tobal-Cupul ◽  
Estela Cerezo-Acevedo ◽  
Yair Yosias Arriola-Gil ◽  
Hector Fernando Gomez-Garcia ◽  
Victor Manuel Romero-Medina
Keyword(s):  
Sensitivity Analysis ◽  
Experimental Tests ◽  
Caribbean Sea ◽  
Ocean Model ◽  
Operating Conditions ◽  
Working Fluid ◽  
Ocean Energy ◽  
Mexican Caribbean ◽  
Water Temperature Data ◽  
Mass Flows

The Mexican Caribbean Sea has potential zones for Ocean Thermal Energy Conversion (OTEC) implementation. Universidad del Caribe and Instituto de Ciencias del Mar y Limnologia, with the support of the Mexican Centre of Innovation in Ocean Energy, designed and constructed a prototype OTEC plant (OTEC-CC-MX-1 kWe), which is the first initiative in Mexico for exploitation of this type of renewable energy. This paper presents a sensitivity analysis whose objective was to know, before carrying out the experimental tests, the behavior of OTEC-CC-MX-1 kWe regarding temperature differences, as well as the non-possible operating conditions, which allows us to assess possible modifications in the prototype installation. An algorithm was developed to obtain the inlet and outlet temperatures of the water and working fluid in the heat exchangers using the monthly surface and deep-water temperature data from the Hybrid Coordinate Ocean Model and Geographically Weighted Regression Temperature Model for the Mexican Caribbean Sea. With these temperatures, the following were analyzed: fluctuation of thermal efficiency, mass flows of R-152a and water and power production. By analyzing the results, we verified maximum and minimum mass flows of water and R-152a to produce 1 kWe during a typical year in the Mexican Caribbean Sea and the conditions when the production of electricity is not possible for OTEC-CC-MX-1 kWe.

scholarly journals Children’s Astronomy. Development of the Shape of the Earth Concept in Polish Children between 5 and 10 Years of Age

2021 ◽  
Vol 11 (2) ◽  
pp. 75
Author(s):  
Jan Amos Jelinek
Keyword(s):  
Mental Model ◽  
Cultural Influences ◽  
Test Results ◽  
The Earth ◽  
Spherical Earth ◽  
The Individual ◽  
High Level ◽  
Cognitive Problems ◽  
Teaching Situations ◽  
Model Approach

The Earth’s shape concept develops as consecutive cognitive problems (e.g., the location of people and trees on the spherical Earth) are gradually resolved. Establishing the order of problem solving may be important for the organisation of teaching situations. This study attempted to determine the sequence of problems to be resolved based on tasks included in the EARTH2 test. The study covered a group of 444 children between 5 and 10 years of age. It captured the order in which children solve cognitive problems on the way to constructing a science-like concept. The test results were compared with previous studies. The importance of cultural influences connected to significant differences (24%) in test results was emphasised. Attention was drawn to the problem of the consistency of the mental model approach highlighted in the literature. The analysis of the individual sets of answers provided a high level of consistency of indications referring to the same model (36%), emphasising the importance of the concept of mental models.

An Opinion on the Assessment of People Who May Have an Auditory Processing Disorder

2012 ◽  
Vol 23 (02) ◽  
pp. 097-105 ◽  
Author(s):  
Harvey Dillon ◽  
Sharon Cameron ◽  
Helen Glyde ◽  
Wayne Wilson ◽  
Dani Tomlin
Keyword(s):  
At Risk ◽  
Auditory Processing ◽  
Specific Form ◽  
Test Battery ◽  
Auditory Processing Disorder ◽  
Test Results ◽  
Hierarchical Approach ◽  
Clinical Efficiency ◽  
Impaired Ability ◽  
The Individual

We need to rethink how we assess auditory processing disorder (APD). The current use of test batteries, while necessary and well accepted, is at risk of failing as the size of these batteries increases. To counter the statistical, fatigue, and clinical efficiency problems of large test batteries, we propose a hierarchical approach to APD assessment. This begins with an overall test of listening difficulty in which performance is measurably affected for anyone with an impaired ability to understand speech in difficult listening conditions. It proceeds with a master test battery containing a small number of single tests, each of which assesses a different group of skills necessary for understanding speech in difficult listening conditions. It ends with a detailed test battery, where the individual tests administered from this battery are only those that differentiate the skills assessed by the failed test(s) from the master test battery, so that the specific form of APD can be diagnosed. An example of how hierarchical interpretation of test results could be performed is illustrated using the Listening in Spatialized Noise—Sentences test (LiSN-S). Although consideration of what abilities fall within the realm of auditory processing should remain an important issue for research, we argue that patients will be best served by focusing on whether they have difficulty understanding speech, identifying the specific characteristics of this difficulty, and specifically remediating and/or managing those characteristics.

Three-Dimensional Flows and Loss Reduction in Axial Compressors

1987 ◽  
Vol 109 (3) ◽  
pp. 354-361 ◽  
Author(s):  
Y. Dong ◽  
S. J. Gallimore ◽  
H. P. Hodson
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Axial Flow ◽  
Tracer Gas ◽  
Suction Surface ◽  
Axial Compressors ◽  
Small Clearance ◽  
Oil Flow ◽  
Stator Blade ◽  
Flow Compressor

Measurements have been performed in a low-speed high-reaction single-stage axial compressor. Data obtained within and downstream of the rotor, when correlated with the results of other investigations, provide a link between the existence of suction surface–hub corner separations, their associated loss mechanisms, and blade loading. Within the stator, it has been shown that introducing a small clearance between the stator blade and the stationary hub increases the efficiency of the stator compared to the case with no clearance. Oil flow visualizaton indicated that the leakage reduced the extensive suction surface–hub corner separation that would otherwise exist. A tracer gas experiment showed that the large radial shifts of the surface streamlines indicated by the oil flow technique were only present close to the blade. The investigation demonstrates the possible advantages of including hub clearance in axial flow compressor stator blade rows.

Design and Analysis of a High Power Density, Low Temperature Waste Heat Recovery System Using an Oil-Free Turboalternator

2010 ◽  
Author(s):  
James F. Walton ◽  
Andrew Hunsberger ◽  
Hooshang Heshmat
Keyword(s):  
Output Power ◽  
Waste Heat ◽  
Maximum Output Power ◽  
Output Power Level ◽  
Working Fluid ◽  
Prototype System ◽  
Low Grade ◽  
Maximum Output ◽  
Test Results ◽  
Study Results

In this paper the authors will present the design and preliminary test results for a distributed electric generating system that uses renewable energy source for economical load-following and peak-shaving capability in an oil-free, high-speed micro-turboalternator system using compliant foil bearings and a permanent magnet alternator. Test results achieved with the prototype system operating to full speed and under power generating mode will be presented. A comparison between predicted and measured electrical output will also be presented up to a power generating level of 25 kWe at approximately 55,000 rpm. The excellent correlation between design and test provides the basis for scale up to larger power levels. Based upon the turboalternator test results a thermodynamic cycle analysis of a system using low grade waste heat water at approximately 100 C will be reviewed. The tradeoff study results for a series of environmentally friendly refrigerant working fluids will also be presented including sensitivity to vaporization and condensing temperatures. Based on the cycle and pinch point analyses predicted maximum output power was determined. Finally a preliminary turbine design for the selected R134a working fluid was completed. The results of this study show that a net output power level of greater than 40 kW is possible for approximately 240 l/m flow of water at 100C is possible.

scholarly journals Thermodynamic Analysis of Irreversible Desiccant Systems

Entropy ◽  
2018 ◽  
Vol 20 (8) ◽  
pp. 595 ◽  
Author(s):  
Niccolò Giannetti ◽  
Seiichi Yamaguchi ◽  
Andrea Rocchetti ◽  
Kiyoshi Saito
Keyword(s):  
Control Volume ◽  
Ideal Gas ◽  
Maximum Efficiency ◽  
Working Fluid ◽  
Specific System ◽  
Equilibrium Relationship ◽  
Working Medium ◽  
Vapour Mixture ◽  
Energy Balances ◽  
Relationship Of

A new general thermodynamic mapping of desiccant systems’ performance is conducted to estimate the potentiality and determine the proper application field of the technology. This targets certain room conditions and given outdoor temperature and humidity prior to the selection of the specific desiccant material and technical details of the system configuration. This allows the choice of the operative state of the system to be independent from the limitations of the specific design and working fluid. An expression of the entropy balance suitable for describing the operability of a desiccant system at steady state is obtained by applying a control volume approach, defining sensible and latent effectiveness parameters, and assuming ideal gas behaviour of the air-vapour mixture. This formulation, together with mass and energy balances, is used to conduct a general screening of the system performance. The theoretical advantage and limitation of desiccant dehumidification air conditioning, maximum efficiency for given conditions constraints, least irreversible configuration for a given operative target, and characteristics of the system for a target efficiency can be obtained from this thermodynamic mapping. Once the thermo-physical properties and the thermodynamic equilibrium relationship of the liquid desiccant mixture or solid coating material are known, this method can be applied to a specific technical case to select the most appropriate working medium and guide the specific system design to achieve the target performance.

Performance Estimation of Axial Flow Turbines

1970 ◽  
Vol 185 (1) ◽  
pp. 407-424 ◽  
Author(s):  
H. R. M. Craig ◽  
H. J. A. Cox
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Gas Turbines ◽  
Three Dimensional ◽  
Axial Flow ◽  
Performance Estimation ◽  
Speed Ratio ◽  
Test Results ◽  
Wide Range ◽  
Relevant Variables

A comprehensive method of estimating the performance of axial flow steam and gas turbines is presented, based on analysis of linear cascade tests on blading, on a number of turbine test results, and on air tests of model casings. The validity of the use of such data is briefly considered. Data are presented to allow performance estimation of actual machines over a wide range of Reynolds number, Mach number, aspect ratio and other relevant variables. The use of the method in connection with three-dimensional methods of flow estimation is considered, and data presented showing encouraging agreement between estimates and available test results. Finally ‘carpets’ are presented showing the trends in efficiencies that are attainable in turbines designed over a wide range of loading, axial velocity/blade speed ratio, Reynolds number and aspect ratio.

1-D Model Analysis of Tesla Turbine for Small Scale Organic Rankine Cycle (ORC) System

2017 ◽  
Author(s):  
Jian Song ◽  
Chun-wei Gu
Keyword(s):  
Large Scale ◽  
Low Cost ◽  
Organic Rankine Cycle ◽  
Axial Flow ◽  
Rankine Cycle ◽  
Expansion Ratio ◽  
Working Fluid ◽  
Small Scale ◽  
Low Grade ◽  
D Model

Energy shortage and environmental deterioration are two crucial issues that the developing world has to face. In order to solve these problems, conversion of low grade energy is attracting broad attention. Among all of the existing technologies, Organic Rankine Cycle (ORC) has been proven to be one of the most effective methods for the utilization of low grade heat sources. Turbine is a key component in ORC system and it plays an important role in system performance. Traditional turbine expanders, the axial flow turbine and the radial inflow turbine are typically selected in large scale ORC systems. However, in small and micro scale systems, traditional turbine expanders are not suitable due to large flow loss and high rotation speed. In this case, Tesla turbine allows a low-cost and reliable design for the organic expander that could be an attractive option for small scale ORC systems. A 1-D model of Tesla turbine is presented in this paper, which mainly focuses on the flow characteristics and the momentum transfer. This study improves the 1-D model, taking the nozzle limit expansion ratio into consideration, which is related to the installation angle of the nozzle and the specific heat ratio of the working fluid. The improved model is used to analyze Tesla turbine performance and predict turbine efficiency. Thermodynamic analysis is conducted for a small scale ORC system. The simulation results reveal that the ORC system can generate a considerable net power output. Therefore, Tesla turbine can be regarded as a potential choice to be applied in small scale ORC systems.

Sign in / Sign up

Export Citation Format

Share Document