The empirical formula for calculating the incident air Kerma in intraoral radiographic imaging

2021 ◽  
pp. 20210117
Author(s):  
Zoran Mirkov ◽  
Katarina M Rajković ◽  
Jovan B Stanković ◽  
Dario Faj

Objectives: The aim of this paper is to determine the empirical formula for calculating the incident air kerma (Ki), used as a patient dose descriptor in the intraoral radiographic imaging. Methods: The data for the formula were collected during the regular annual inspection of intraoral dental X-ray units in 2018, 2019 and early 2020. The measurement data of 50 X-ray units were processed to develop the formula. Exposure factors for imaging molars of the upper jaw of an average patient in a clinical setting were used in the measurement. The formula validity was statistically evaluated using coefficient of correlation, standard error of the fitted function and the mean relative percentage deviation. Results: measurement values of the radiation doses and calculated values obtained by using the final formula showed good agreement - the mean relative percentage deviation values less than ±15%. Conclusions: Although there are differences in X-ray units, voltages, manufacturers and device architectures (single-phase and high-frequency), the measurement data comply well with computed ones in all cases.

2019 ◽  
Vol 48 (5) ◽  
pp. 20180301 ◽  
Author(s):  
Richard Smith ◽  
Richard Tremblay ◽  
Graeme M Wardlaw

Objectives: Evaluate stray radiation to the operator, as represented by a plane within the significant zone of occupancy (SZO), produced by five models of hand-held intraoral dental X-ray devices (HIDXDs). Methods: The stray radiation for five models of HIDXDs was measured, using an anthropomorphic tissue-equivalent head phantom as a scattering object. An ionization chamber was used to measure the air kerma (μGy) at 63 positions in a 160 cm high by 60 cm wide plane that was 10 cm behind the X-ray device, identified as being within the SZO. Results: Based on the measured air kerma from stray radiation of five different HIDXDs, the estimated annual air kerma at all measured spatial positions was calculated. When calculated using a median air kerma of 0.8 mGy at the distal end of the cone, as typically required for digital image receptors, 1 the ranges for estimated annual air kerma in the SZO across the devices were 0.14–0.77 mGy for the median, 0.41–1.01 mGy for the mean, and 1.32–2.55 mGy for the maximum. Similarly, when calculated using a median air kerma of 1.6 mGy as typically required for D-speed film, 2 the ranges for estimated annual air kerma across the devices were 0.28–1.54 mGy for the median, 0.83–2.03 mGy for the mean, and 2.64–5.10 mGy for the maximum. Conclusions: From measured air kerma values of stray radiation in the SZO, estimated annual exposures to the operator for HIDXDs are expected to be greater than from conventional wall-mounted or portable devices activated from a protected area (at a distance or behind shielding). HIDXDs should therefore only be used when patient accessibility makes their use necessary and the use of a portable device on a stand or a wall-mounted device is not reasonably feasible. This approach would keep occupational radiation exposures of dental workers as low as reasonably achievable.


2021 ◽  
pp. 76-82
Author(s):  
S.І. Doroshenko ◽  
I.S. Kuzmenko ◽  
K.V. Storozhenko ◽  
S.V. Irkha ◽  
Kh.M. Demianchuk

No tooth is as problematic for patients as it is for third molars. After erupting later than all teeth, they often have little space in the dentition, or rather in the retromolar space, which should appear, above all, with further growth of the jaws. Therefore, the timing of their eruption varies considerably and is often accompanied by the appearance of significant morphological and functional disorders. That is why it is necessary to take a balanced approach to the preservation of third molars in the dental arch, providing them with a place in the retromolar space by timely detecting their condition and position in the jawbones and thus preserving the integrity of the dentition and implementing the fourth and last stage of bite raising in orthodontic patients with dental anomalies. The purpose of the study. To substantiate a differentiated approach to the preservation of third molars in orthodontic treatment by determining their condition and position in the jaw. Material and methods of research. For this purpose, 44 patients aged 15-30 years with different dentofacial anomalies having full permanent dentition including third molars confirmed by clinical and X-ray data were examined and given orthodontic treatment. Additional methods of the study included analysis of diagnostic model measurements (by Pont Korkhaus method). Furthermore, retromolar space was measured to find out if there is a space for third molars in the row of teeth by measuring its length and height using a silicone index (by S.I. Doroshenko and Ye.A. Kulhinskyi's method, 2009). X-ray studies included analysis of orthopantomograms (OPG), teleradiography (TRG), computed tomography (CT) scan, etc. The OPG analysis was conducted using K.V. Storozhenko's method (2013) which involved measuring the inclination of teeth, especially third and second molars relative to the jaw base. OPG showed a lack of space for third molars using S.I. Doroshenko and Ye.A. Kulhinskyi's method (2009). Measurement data were processed using mathematical statistics. The mean and the confidence interval for the data sample were calculated according to GOST R 8.736 – 2011. Results. The analysis of data showed significant variability in inclination of third molars relative to the jaw base and second molars on both sides of the jaws (on the left and the right). The largest difference in inclinations of third and second molars was observed in the lower jaw (LJ) both on the left and the right, with an insignificant deviation of 0.3° ± 0.2°, and the least difference was in the upper jaw (UJ), especially on the left, but with a larger deviation of 3.6° ± 0.2°. The conducted studies suggested that the larger the difference in inclinations of third lower molars relative to second ones is, the more problematic their eruption is, since they erupt later. Lower third molars incline medially at their crowns and therefore they have a smaller angle of inclination relative to the LJ base. While erupting upper third molars incline distally at their crown with an increased angle of inclination relative to the UJ base. In 44 patients aged 15-30 years, 106 (60.2%) third molars were in retention, including 35 (33.1%) teeth in physiological retention in younger people, 40 (37,7%) teeth in half-retention, and 31 (29.2%) third molars in constant retention. An important factor in predicting the eruption of third molars became the presence of space for them in retromolar space, both sagittally and vertically. The presence of space in the row of teeth, i. e. sagittally, was observed in 25 (14.2%) of 176 third molars: in LJ in 15 (8.5%) molars, especially on the left in 7 (4.0%), and on the right in 8 (4.5%) teeth; in UJ in 10 (5.7%) teeth – 6 (3.4%) and 4 (2.3%) respectively. The presence of space for the third molars also depended on width at the equator, which appeared to be the smallest in UJ and varied from 10 mm to 15 mm with a mean of 11.7 mm, and the largest in LJ – from 12 mm to 19 mm, the mean was 14.17 mm. Differences in the means between left and right UJ third molars were not detected (11.8 mm and 11.8 mm respectively), and in LJ it was insignificant (14.2 mm and 14.1 mm). In individual cases, the difference was 2.0-4.0 mm, and 1.0 mm in LJ. The latter confirms some scientists’ conclusions that the sizes of upper third molars vary more widely. Retention of third molars in the subjects was associated with different dentofacial anomalies most commonly reported in 17 (38.6%) patients with distal occlusion (class ІІ) and in 13 (29.5%) persons with deep occlusion, and more rarely seen with medial (class ІІІ) – 4 (9.1%) – and open occlusion – 4 (9.1%). Clinical studies suggested that when selecting a tactic for treatment of retained teeth, apart from determining their position in jawbones and the presence of a sagittal space in the row of teeth, it is also necessary to determine the size of vertical retromolar space for them which was measured using silicone indexes. Persons with deep and distal occlusion had the narrowest alveolar space from 0.5 mm to 4 mm, while in those with neutral occlusion it was from 5 mm to 7 mm. Thus, the conducted studies showed the importance of the differentiated approach to the preservation of third molars, especially during orthodontic treatment.


2021 ◽  
Vol 22 (1) ◽  
pp. 20-34
Author(s):  
Akintayo Daniel Omojola ◽  
Samuel Olaolu Adeneye ◽  
Michael Onoriode Akpochafor ◽  
Isiaka Olusola Akala ◽  
Azuka Anthonio Agboje

Objective: Radiation detectors are key components that ensure the accuracy and performances of dosimetry equipment. The study is aimed to compare the mean entrance surface air kerma (ESAK) between a DCT-10mm ionization chamber (IC) and MTS-N (LiF: Mg, Ti) chips when both detectors are exposed to ≤ 5mGy with a 10 by 10 field size, with an X-ray source and to determine the accuracy of the Thermoluminescent (TL) chips. Also, the dose will be compared to similar studies. Materials and Methods: A functional, Digital Radiography (DR) X-ray System was used. A DCT-10mm ionization chamber (IC) and an XR Multidetector was positioned at a Source to Image Distance (SID) of 100cm on polystyrene, about 20cm thick. An X-ray spectrum generated at a Practical Peak Voltage (PPV) of 60-107kV with Half Value Layer (HVL) of 2.4-4.3mmAl and filtration > 3mmAl was used. The same setup was used for the MTS-N chips. Results: The mean doses for 1-5 mGy with the MTS-N chips were 1.07±0.07, 1.60±0.13, 2.23±0.11, 2.58±0.07 and 3.45±0.10 mGy respectively, with accuracies of 7, 20, 26, 36 and 31%. Dose accuracy at 1and 2mGy was within 25% respectively. Dose accuracies at 3, 4 and 5mGy was within >25%. The correction factor for 1-5mGy was 0.94, 1.25, 1.35, 1.55 and 1.45 respectively. Conclusion: Validation of the MTS-N chips with the reference ionization chamber to this study was within 36%. The Radiation and Nuclear Safety Authority (STUK) recommends that ESAK be within 25% for entrance surface dose. ESAK accuracy mostly increased with dose as observed in this study.


2019 ◽  
Vol 37 (1) ◽  
pp. 51
Author(s):  
Atchara Promduang ◽  
Napapong Pongnapang ◽  
Napat Ritlumlert ◽  
Sutthirak Tangruangkiat ◽  
Monchai Phonlakrai

Objective: The main purpose of this study was to investigate the typical dose for standard-sized patients in chest (posteroanterior; PA) and abdomen (anteroposterior; AP) digital radiography.Material and Methods: The air kerma was measured by the ionization chamber (Radical Corporation, model 10X6-6) in X-ray equipment manufactured by General Electric Healthcare Definium 8000 System for different kilovoltage peak (kVp) settings in each X-ray examination. The entrance surface air kerma (ESAK) was determined in 422 mediumsized patients in different projections: chest (PA) and abdomen (AP), according to the recommended protocol of the International Atomic Energy Agency Technical Report Series Number 457 (Technical Reports Series No. 457 “Dosimetry in Diagnostic Radiology: An International Code of Practice).Results: The mean entrance surface air kerma values for chest (PA) radiography in female and male patients were 0.08 milligray (mGy) and 0.09 mGy, respectively and for abdomen (AP) radiography for both genders were 0.98 mGy and 1.06 mGy, respectively.Conclusion: The mean entrance surface air kerma values of this study were less than the diagnostic reference levels from the IAEA 1996, Korea 2007, United Kingdom 2010 and Japan 2015, in all projections. Patient doses (ESAK) in chest (PA) and abdomen (AP) digital radiography at Chulabhorn Hospital were less than the other guidelines, because of the use of a high kVp technique for the chest and the automatic exposure control for the abdomen. Furthermore, Thai people are smaller than Westerners. We studied in digital radiography only that literally provides lowest radiation dose compares with screen film and computed radiography.


2020 ◽  
Vol 190 (4) ◽  
pp. 419-426
Author(s):  
Nada A Ahmed ◽  
E H Basheir ◽  
A B Farah ◽  
T S Mohammedzein ◽  
I I Suliman

Abstract This study aimed to calculate patient radiation doses for adults during the seven most commonly performed conventional X-ray procedures, and to propose national diagnostic reference levels (DRLs). A representative sample of patients from 29 hospitals was included. The entrance surface air kerma (ESAK) was calculated by measuring X-ray tube output and the corresponding technical and exposure factors for each patient. Third-quartile values of the mean ESAK distributions were proposed as DRL values. The DRLs in mGy were as follows: 0.6 for chest postero–anterior (PA), 3.5 for skull AP, 1.7 for skull lateral (LAT), 2.7 for abdominal, 2.6 for pelvic AP, 3.7 for lumbar spine AP and 8 for lumbar spine LAT. Compared with literature, the maximum percentages increase were in chest PA (329%) and skull AP (187%). Since the suggested DRL for chest PA was higher than literature values, dose optimization and a review of its value is recommended.


Author(s):  
William F. Tivol ◽  
Murray Vernon King ◽  
D. F. Parsons

Feasibility of isomorphous substitution in electron diffraction is supported by a calculation of the mean alteration of the electron-diffraction structure factors for hemoglobin crystals caused by substituting two mercury atoms per molecule, following Green, Ingram & Perutz, but with allowance for the proportionality of f to Z3/4 for electron diffraction. This yields a mean net change in F of 12.5%, as contrasted with 22.8% for x-ray diffraction.Use of the hydration chamber in electron diffraction opens prospects for examining many proteins that yield only very thin crystals not suitable for x-ray diffraction. Examination in the wet state avoids treatments that could cause translocation of the heavy-atom labels or distortion of the crystal. Combined with low-fluence techniques, it enables study of the protein in a state as close to native as possible.We have undertaken a study of crystals of rat hemoglobin by electron diffraction in the wet state. Rat hemoglobin offers a certain advantage for hydration-chamber work over other hemoglobins in that it can be crystallized from distilled water instead of salt solutions.


Author(s):  
Noriyuki Kuwano ◽  
Masaru Itakura ◽  
Kensuke Oki

Pd-Ce alloys exhibit various anomalies in physical properties due to mixed valences of Ce, and the anomalies are thought to be strongly related with the crystal structures. Since Pd and Ce are both heavy elements, relative magnitudes of (fcc-fpd) are so small compared with <f> that superlattice reflections, even if any, sometimes cannot be detected in conventional x-ray powder patterns, where fee and fpd are atomic scattering factors of Ce and Pd, and <f> the mean value in the crystal. However, superlattices in Pd-Ce alloys can be analyzed by electron microscopy, thanks to the high detectability of electron diffraction. In this work, we investigated modulated superstructures in alloys with 12.5 and 15.0 at.%Ce.Ingots of Pd-Ce alloys were prepared in an arc furnace under atmosphere of ultra high purity argon. The disc specimens cut out from the ingots were heat-treated in vacuum and electrothinned to electron transparency by a jet method.


Reproduction ◽  
2000 ◽  
pp. 331-336 ◽  
Author(s):  
L Holm ◽  
H Ekwall ◽  
GJ Wishart ◽  
Y Ridderstrale

Sperm storage tubules from the utero-vaginal junction of chickens, quails and turkeys were analysed for calcium and zinc using X-ray microanalysis of ultra-rapidly frozen tissue in a scanning electron microscope. This technique enabled the tubular fluid surrounding the stored spermatozoa and the intracellular content of the cells of the sperm storage tubules to be analysed separately and, by using standards with known concentrations, their elemental concentrations were estimated. The mean (+/- SEM) concentration of calcium in the tubular fluid from chickens, quails and turkeys was 17 +/- 3, 19 +/- 3 and 17 +/- 4 mmol kg(-1) wet weight, respectively. The intracellular calcium concentration of the cells of the tubules did not differ significantly from these values and was also similar in the mucosal epithelial cells of the utero-vaginal junction. Zinc was localized in the cells of turkey sperm storage tubules and tubular fluid, but at low concentrations. No zinc could be detected in corresponding structures from chickens and quails. The concentration of calcium in the tubular fluid is within the range known to inhibit the motility of spermatozoa, supporting this function for calcium during storage. Zinc is known to depress turkey sperm metabolism and it may also be involved in inducing quiescence of spermatozoa during storage in this species.


2013 ◽  
Vol 27 (4) ◽  
pp. 419-424 ◽  
Author(s):  
S.J. Kovalyshyn ◽  
O.P. Shvets ◽  
S. Grundas ◽  
J. Tys

Abstract The paper presents the results of a study of the use of electro-separation methods for improvement of the utility value of 5 winter rapeseed cultivars. The process of electro-separation of rapeseed was conducted on a prototype apparatus built at the Laboratory of Application of Electro-technologies in Agriculture, Lviv National Agriculture University. The process facilitated separation of damaged, low quality seeds from the sowing material. The initial mean level of mechanically damaged seeds in the winter rapeseed cultivars studied varied within the range of 15.8-20.1%. Verification of the amount of seeds with mechanical damage was performed on X-ray images of seeds acquired by means of a digital X-ray apparatus. In the course of analysis of the X-ray images, it was noted that the mean level of mechanical damage to the seeds after the electro-separation was in the range of 2.1-3.8%. The application of the method of separation of rapeseeds in the corona discharge field yielded a significant reduction of the level of seeds with mechanical damage. The application of the method in practice may effectively contribute to improvement of the utility value of sowing material or seed material for production of edible oil.


1991 ◽  
Vol 22 (5) ◽  
pp. 327-340 ◽  
Author(s):  
K. Høgh Jensen ◽  
J. C. Refsgaard

A numerical analysis of solute transport in two spatially heterogeneous fields is carried out assuming that the fields are composed of ensembles of one-dimensional non-interacting soil columns, each column representing a possible soil profile in statistical terms. The basis for the analysis is the flow simulation described in Part II (Jensen and Refsgaard, this issue), which serves as input to a transport model based on the convection-dispersion equation. The simulations of the average and variation in solute concentration in planes perpendicular to the flow direction are compared to measurements obtained from tracer experiments carried out at the two fields. Due to the limited amount of measurement data, it is difficult to draw conclusive evidence of the simulations, but reliable simulations are obtained of the mean behaviour within the two fields. The concept of equivalent soil properties is also tested for the transport problem in heterogeneous soils. Based on effective parameters for the retention and hydraulic conductivity functions it is possible to predict the mean transport in the two experimental fields.


Sign in / Sign up

Export Citation Format

Share Document