Use of the electro-separation method for improvement of the utility value of winter rapeseeds

2013 ◽  
Vol 27 (4) ◽  
pp. 419-424 ◽  
Author(s):  
S.J. Kovalyshyn ◽  
O.P. Shvets ◽  
S. Grundas ◽  
J. Tys
Keyword(s):  
Corona Discharge ◽  
Mechanical Damage ◽  
Edible Oil ◽  
Separation Method ◽  
Utility Value ◽  
X Ray ◽  
Winter Rapeseed ◽  
The Mean ◽  
Discharge Field ◽  
Prototype Apparatus

Abstract The paper presents the results of a study of the use of electro-separation methods for improvement of the utility value of 5 winter rapeseed cultivars. The process of electro-separation of rapeseed was conducted on a prototype apparatus built at the Laboratory of Application of Electro-technologies in Agriculture, Lviv National Agriculture University. The process facilitated separation of damaged, low quality seeds from the sowing material. The initial mean level of mechanically damaged seeds in the winter rapeseed cultivars studied varied within the range of 15.8-20.1%. Verification of the amount of seeds with mechanical damage was performed on X-ray images of seeds acquired by means of a digital X-ray apparatus. In the course of analysis of the X-ray images, it was noted that the mean level of mechanical damage to the seeds after the electro-separation was in the range of 2.1-3.8%. The application of the method of separation of rapeseeds in the corona discharge field yielded a significant reduction of the level of seeds with mechanical damage. The application of the method in practice may effectively contribute to improvement of the utility value of sowing material or seed material for production of edible oil.

Isomorphous replacement in electron diffraction of wet crystals of rat hemoglobin

1983 ◽  
Vol 41 ◽  
pp. 446-447
Author(s):  
William F. Tivol ◽  
Murray Vernon King ◽  
D. F. Parsons
Keyword(s):  
Electron Diffraction ◽  
Heavy Atom ◽  
Isomorphous Substitution ◽  
X Ray Diffraction ◽  
Salt Solutions ◽  
X Ray ◽  
Isomorphous Replacement ◽  
Structure Factors ◽  
Diffraction Structure ◽  
The Mean

Feasibility of isomorphous substitution in electron diffraction is supported by a calculation of the mean alteration of the electron-diffraction structure factors for hemoglobin crystals caused by substituting two mercury atoms per molecule, following Green, Ingram & Perutz, but with allowance for the proportionality of f to Z3/4 for electron diffraction. This yields a mean net change in F of 12.5%, as contrasted with 22.8% for x-ray diffraction.Use of the hydration chamber in electron diffraction opens prospects for examining many proteins that yield only very thin crystals not suitable for x-ray diffraction. Examination in the wet state avoids treatments that could cause translocation of the heavy-atom labels or distortion of the crystal. Combined with low-fluence techniques, it enables study of the protein in a state as close to native as possible.We have undertaken a study of crystals of rat hemoglobin by electron diffraction in the wet state. Rat hemoglobin offers a certain advantage for hydration-chamber work over other hemoglobins in that it can be crystallized from distilled water instead of salt solutions.

Long-period modulated superstructures in Pd-12.5 at.%Ce and Pd-15 at.%Ce alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 164-165
Author(s):  
Noriyuki Kuwano ◽  
Masaru Itakura ◽  
Kensuke Oki
Keyword(s):  
Electron Microscopy ◽  
Mean Value ◽  
Heavy Elements ◽  
Arc Furnace ◽  
X Ray ◽  
Long Period ◽  
Ultra High Purity ◽  
Heat Treated ◽  
Atomic Scattering ◽  
The Mean

Pd-Ce alloys exhibit various anomalies in physical properties due to mixed valences of Ce, and the anomalies are thought to be strongly related with the crystal structures. Since Pd and Ce are both heavy elements, relative magnitudes of (fcc-fpd) are so small compared with <f> that superlattice reflections, even if any, sometimes cannot be detected in conventional x-ray powder patterns, where fee and fpd are atomic scattering factors of Ce and Pd, and <f> the mean value in the crystal. However, superlattices in Pd-Ce alloys can be analyzed by electron microscopy, thanks to the high detectability of electron diffraction. In this work, we investigated modulated superstructures in alloys with 12.5 and 15.0 at.%Ce.Ingots of Pd-Ce alloys were prepared in an arc furnace under atmosphere of ultra high purity argon. The disc specimens cut out from the ingots were heat-treated in vacuum and electrothinned to electron transparency by a jet method.

Localization of calcium and zinc in the sperm storage tubules of chicken, quail and turkey using X-ray microanalysis

Reproduction ◽  
2000 ◽  
pp. 331-336 ◽  
Author(s):  
L Holm ◽  
H Ekwall ◽  
GJ Wishart ◽  
Y Ridderstrale
Keyword(s):  
Calcium Concentration ◽  
Sperm Storage ◽  
X Ray ◽  
Elemental Concentrations ◽  
Low Concentrations ◽  
Intracellular Content ◽  
Wet Weight ◽  
The Mean ◽  
Sperm Storage Tubules ◽  
Scanning Electron

Sperm storage tubules from the utero-vaginal junction of chickens, quails and turkeys were analysed for calcium and zinc using X-ray microanalysis of ultra-rapidly frozen tissue in a scanning electron microscope. This technique enabled the tubular fluid surrounding the stored spermatozoa and the intracellular content of the cells of the sperm storage tubules to be analysed separately and, by using standards with known concentrations, their elemental concentrations were estimated. The mean (+/- SEM) concentration of calcium in the tubular fluid from chickens, quails and turkeys was 17 +/- 3, 19 +/- 3 and 17 +/- 4 mmol kg(-1) wet weight, respectively. The intracellular calcium concentration of the cells of the tubules did not differ significantly from these values and was also similar in the mucosal epithelial cells of the utero-vaginal junction. Zinc was localized in the cells of turkey sperm storage tubules and tubular fluid, but at low concentrations. No zinc could be detected in corresponding structures from chickens and quails. The concentration of calcium in the tubular fluid is within the range known to inhibit the motility of spermatozoa, supporting this function for calcium during storage. Zinc is known to depress turkey sperm metabolism and it may also be involved in inducing quiescence of spermatozoa during storage in this species.

scholarly journals Preparation of high-entropy carbides by different sintering techniques

2021 ◽  
Vol 56 (19) ◽  
pp. 11237-11247 ◽  
Author(s):  
Johannes Pötschke ◽  
Manisha Dahal ◽  
Mathias Herrmann ◽  
Anne Vornberger ◽  
Björn Matthey ◽  
...  
Keyword(s):  
Grain Size ◽  
Single Phase ◽  
X Ray Diffraction ◽  
Vacuum Sintering ◽  
X Ray ◽  
High Entropy ◽  
Mean Grain Size ◽  
The Mean ◽  
Gas Pressure Sintering ◽  
Hardness Values

AbstractDense (Hf, Ta, Nb, Ti, V)C- and (Ta, Nb, Ti, V, W)C-based high-entropy carbides (HEC) were produced by three different sintering techniques: gas pressure sintering/sinter–HIP at 1900 °C and 100 bar Ar, vacuum sintering at 2250 °C and 0.001 bar as well as SPS/FAST at 2000 °C and 60 MPa pressure. The relative density varied from 97.9 to 100%, with SPS producing 100% dense samples with both compositions. Grain size measurements showed that the substitution of Hf with W leads to an increase in the mean grain size of 5–10 times the size of the (Hf, Ta, Nb, Ti, V,)C samples. Vacuum-sintered samples showed uniform grain size distribution regardless of composition. EDS mapping revealed the formation of a solid solution with no intermetallic phases or element clustering. X-ray diffraction analysis showed the structure of mostly single-phase cubic high-entropy carbides. Hardness measurements revealed that (Hf, Ta, Nb, Ti, V)C samples possess higher hardness values than (Ta, Nb, Ti, V, W)C samples.

scholarly journals AB0267 BODY COMPOSITION IN PATIENTS WITH RHEUMATOID ARTHRITIS

2020 ◽  
Vol 79 (Suppl 1) ◽  
pp. 1432.2-1432
Author(s):  
N. Toroptsova ◽  
O. Dobrovolskaya ◽  
N. Demin ◽  
L. Shornikova
Keyword(s):  
Rheumatoid Arthritis ◽  
Body Composition ◽  
Muscle Mass ◽  
Dual Energy ◽  
X Ray ◽  
T Score ◽  
Osteosarcopenic Obesity ◽  
The Mean ◽  
Total Fat ◽  
Appendicular Muscle Mass

Background:Rheumatoid arthritis (RA) is a complex inflammatory disease that modifies body composition. Using the dual-energy x-ray absorptiometry (DXA) in RA patients could be a method for body composition changes detection.Objectives:To study the body composition using DXA in patients with RA.Methods:The study involved 79 women with RA, median age 60 [55; 65] years. The bone mineral density (BMD) was measured by dual-energy x-ray absorptiometry using «Discovery A» (Hologic, USA). Assessment of body composition was carried out, using the program «Whole body». Sarcopenia (SP) was diagnosed as a decrease in appendicular mass index (AMI) <6.0 kg/m2. Osteoporosis (OP) was diagnosed as a decrease in T-score <-2.5 SD. Osteosarcopenia was determined when T-score was <-1.0 SD, AMI was <6.0 kg/m2, osteosarcopenic obesity - T-score was <-1.0 SD, AMI was <6.0 kg/m2and total fat was >35%.Results:The mean duration of RA was 9 [3; 11] years. The mean body mass index (BMI) was 27.6±4.8 kg/m2. Disease activity score in 28 joints-erythrocyte sedimentation rate was 4.5±1.3 points for the group. 39 (49.3%) patients used oral glucocorticoids continuously. Appendicular muscle mass and AMI were on average 17.8±3.0 kg and 6.8±1.0 kg/m2, respectively. AMI <6 kg/m2was detected in 20 (25.3%) patients. 56 (70.9%) women with RA had total fat > 35%, while only 22 (27.8%) of women with RA had obesity according to BMI (BMI >30 kg/m2). Isolated OP was found in 13 (16.5%), osteosarcopenia in 7 (8.9%) and osteosarcopenic obesity in 13 (16.5%) patients RA. No cases with isolated sarcopenia or sarcopenic obesity were detected. Only 3 (3.8%) patients did not have appendicular muscle mass, AMI and BMD decrease and overfat or obesity.Conclusion:About 97% women with RA had abnormal body composition phenotype: 16,5% - OP, 8.9% -osteosarcopenia, 16,5% - osteosarcopenic obesity and 54,4% - overfat.Disclosure of Interests:None declared

Dalnegroite, Tl5–xPb2x(As,Sb)2l–xS34, a new thallium sulphosalt from Lengenbach quarry, Binntal, Switzerland

2009 ◽  
Vol 73 (6) ◽  
pp. 1027-1032 ◽  
Author(s):  
F. Nestola ◽  
A. Guastoni ◽  
L. Bindi ◽  
L. Secco
Keyword(s):  
Polarized Light ◽  
New Mineral ◽  
X Ray Diffraction ◽  
X Ray ◽  
Elemental Concentrations ◽  
Reflected Light ◽  
Mohs Hardness ◽  
The Mean ◽  
The University ◽  
Probable Space

AbstractDalnegroite, ideally Tl4Pb2(As12Sb8)Σ20S34, is a new mineral from Lengenbach, Binntal, Switzerland. It occurs as anhedral to subhedral grains up to 200 μm across, closely associated with realgar, pyrite, Sb-rich seligmanite in a gangue of dolomite. Dalnegroite is opaque with a submetallic lustre and shows a brownish-red streak. It is brittle; the Vickers hardness (VHN25) is 87 kg mm-2(range: 69—101) (Mohs hardness ∼3—3½). In reflected light, dalnegroite is highly bireflectant and weakly pleochroic, from white to a slightly greenish-grey. In cross-polarized light, it is highly anisotropic with bluish to green rotation tints and red internal reflections.According to chemical and X-ray diffraction data, dalnegroite appears to be isotypic with chabournéite, Tl5-xPb2x(Sb,As)21-xS34. It is triclinic, probable space groupP1, witha= 16.217(7) Å,b= 42.544(9) Å,c= 8.557(4) Å, α = 95.72(4)°, β = 90.25(4)°, γ = 96.78(4)°,V= 5832(4) Å3,Z= 4.The nine strongest powder-diffraction lines [d(Å) (I/I0) (hkl)] are: 3.927 (100) (10 0); 3.775 (45) (22); 3.685 (45) (60); 3.620 (50) (440); 3.124 (50) (2); 2.929 (60) (42); 2.850 (70) (42); 2.579 (45) (02); 2.097 (60) (024). The mean of 11 electron microprobe analyses gave elemental concentrations as follows: Pb 10.09(1) wt.%, Tl 20.36(1), Sb 23.95(1), As 21.33(8), S 26.16(8), totalling 101.95 wt.%, corresponding to Tl4.15Pb2.03(As11.86Sb8.20)S34. The new mineral is named for Alberto Dal Negro, Professor in Mineralogy and Crystallography at the University of Padova since 1976.

scholarly journals Estimation of dose and cancer risk to newborn from chest X-ray in South-South Nigeria: a call for protocol optimization

2021 ◽  
Vol 52 (1) ◽  
Author(s):  
Akintayo Daniel Omojola ◽  
Michael Onoriode Akpochafor ◽  
Samuel Olaolu Adeneye ◽  
Isiaka Olusola Akala ◽  
Azuka Anthonio Agboje
Keyword(s):  
Cancer Risk ◽  
Age Groups ◽  
Field Size ◽  
Radiological Protection ◽  
International Studies ◽  
X Ray ◽  
Thermoluminescent Dosimeters ◽  
Chest X Ray ◽  
Neonatal Patient ◽  
The Mean

Abstract Background The use of X-ray as a diagnostic tool for complication and anomaly in the neonatal patient has been helpful, but the effect of radiation on newborn stands to increase their cancer risk. This study aims to determine the mean, 50th percentile (quartile 2 (Q2)), and 75th percentile (quartile 3 (Q3)) entrance surface dose (ESD) from anteroposterior (AP) chest X-ray and to compare our findings with other relevant studies. The study used calibrated thermoluminescent dosimeters (TLDs), which was positioned on the central axis of the patient. The encapsulated TLD chips were held to the patients’ body using paper tape. The mean kilovoltage peak (kVp) and milliampere seconds (mAs) used was 56.63(52–60) and 5.7 (5–6.3). The mean background TLD counts were subtracted from the exposed TLD counts and a calibration factor was applied to determine ESD. Results The mean ESDs of the newborn between 1 and 7, 8 and 14, 15 and 21, and 22 and 28 days were 1.09 ± 0.43, 1.15 ± 0.50, 1.19 ± 0.45, and 1.32 ± 0.47 mGy respectively. A one-way ANOVA test shows that there were no differences in the mean doses for the 4 age groups (P = 0.597). The 50th percentile for the 4 age groups was 1.07, 1.26, 1.09, and 1.29 mGy respectively, and 75th percentile were 1.41, 1.55, 1.55, and 1.69 mGy respectively. The mean effective dose (ED) in this study was 0.74 mSv, and the estimated cancer risk was 20.7 × 10−6. Conclusion ESD was primarily affected by the film-focus distance (FFD) and the patient field size. The ESD at 75th percentile and ED in this study was higher compared to other national and international studies. The estimated cancer risk to a newborn was below the International Commission on Radiological Protection (ICRP) limit for fatal childhood cancer (2.8 × 10−2Sv−1).

A Small-Angle X-Ray Scattering Study on Pre-Irradiated Malate Synthase. The Influence of Formate, Superoxide Dismutase, and Catalase on the X-Ray Induced Aggregation of the Enzyme

1985 ◽  
Vol 40 (5-6) ◽  
pp. 364-372 ◽  
Author(s):  
P. Zipper ◽  
R. Wilfing ◽  
M. Kriechbaum ◽  
H. Durchschlag
Keyword(s):  
Aqueous Solution ◽  
Superoxide Dismutase ◽  
Small Angle ◽  
Malate Synthase ◽  
X Ray ◽  
X Ray Scattering ◽  
X Irradiation ◽  
The Mean ◽  
Induced Aggregation ◽  
Ray Scattering

Abstract The sulfhydryl enzyme malate synthase from baker’s yeast was X-irradiated with 6 kGy in air-saturated aqueous solution (enzyme concentration: ≃ 10 mg/ml; volume: 120 μl), in the absence or presence of the specific scavengers formate, superoxide dismutase, and catalase. After X-irradiation, a small aliquot of the irradiated solutions was tested for enzymic activity while the main portion was investigated by means of small-angle X-ray scattering. Additionally, an unir­radiated sample without additives was investigated as a reference. Experiments yielded the fol­lowing results: 1. X-irradiation in the absence of the mentioned scavengers caused considerable aggregation, fragmentation, and inactivation of the enzyme. The dose Dt37 for total (= repairable + non­-repayable) inactivation resulted as 4.4 kGy. The mean radius of gyration was found to be about 13 nm. The mean degree of aggregation was obtained as 5.7, without correction for fragmenta­tion. An estimation based on the thickness factor revealed that about 19% of material might be strongly fragmented. When this amount of fragments was accordingly taken into account, a value of 7.1 was obtained as an upper limit for the mean degree of aggregation. The observed retention of the thickness factor and the finding of two different cross-section factors are in full accord with the two-dimensional aggregation model established previously (Zipper and Durchschlag, Radiat. Environ. Biophys. 18, 99 - 121 (1980)). 2. The presence of catalytic amounts of superoxide dismutase and/or catalase, in the absence of formate, during X-irradiation reduced both aggregation and inactivation significantly. 3. The presence of formate (10 or 100 mᴍ) during X-irradiation led to a strong decrease of aggregation and inactivation. This effect was more pronounced with the higher formate concen­tration or when superoxide dismutase and/or catalase were simultaneously present during X-irradiation. The presence of formate also reduced the amount of fragments significantly. 4. The results clearly show that the aggregation and inactivation of malate synthase upon X-irradiation in aqueous solution are mainly caused by OH·; to a minor extent O·̄2 and H2O2 are additionally involved in the damaging processes.

Chalkogenolat-Ionen und ihre Derivate, V Kristall- und Molekülstruktur von 2.8-Dimethyldibenzo [c.g] [1.2.5.6] tetrathiacyclooktadien, einem Oxidationsprodukt von 4-Methylbenzol-1.2-dithiol/Chalcogenolates and their Derivatives, V Crystal and Molecular Structure of 2.8-Dimethyldibenzo[c,g][1,2,5,6]tetrathiaocin, an Oxidation Product of 4-Methylbenzene-1,2-dithiol

1979 ◽  
Vol 34 (1) ◽  
pp. 48-51 ◽  
Author(s):  
Jürgen Kopf ◽  
Klaus von Deuten ◽  
Bahman Nakhdjavan ◽  
Günter Klar
Keyword(s):  
Molecular Structure ◽  
Dihedral Angle ◽  
Oxidation Product ◽  
Crystal And Molecular Structure ◽  
X Ray ◽  
The Mean ◽  
Ray Methods ◽  
Anti Form

Abstract The structure of 2,8-dimethyldibenzo[c,g][1,2,5,6]tetrathiaocin (1b) has been determined by X-ray methods and discussed in connection with the preferred conformations of diaryl disulfides. The compound has the anti-form I. The SS-distance is 205.8 pm, the mean CSS-angle 104.1°, and the CSS/SSC-dihedral angle 111.1°.

Mechanical Spectroscopy Investigation of Liquid Pb-Bi Alloys

2012 ◽  
Vol 184 ◽  
pp. 434-439 ◽  
Author(s):  
Roberto Montanari ◽  
Alessandra Varone
Keyword(s):  
Distribution Functions ◽  
X Ray Diffraction ◽  
Mechanical Spectroscopy ◽  
X Ray ◽  
Neutron Spallation Source ◽  
Driven System ◽  
Spallation Source ◽  
Accelerator Driven System ◽  
The Mean ◽  
Diffraction Patterns

Liquid Pb–Bi eutectic alloy has been selected as coolant and neutron spallation source for the development of MYRRHA, an accelerator driven system. The alloy has been characterized in liquid state from melting (125 °C) to 650 °C by mechanical spectroscopy. Experiments have been carried out using hollow reeds of austenitic stainless steel filled with the Pb-Bi alloy and sealed at the extremities. From 350 °C to 520 °C modulus shows a remarkable drop accompanied by a broad internal friction maximum. In the same temperature range radial distribution functions, determined from X-ray diffraction patterns, evidenced variations of the mean distance between the 1st nearest neighbour atoms. The anelastic phenomena have been attributed to a structural re-arrangement of liquid metal. For comparison, other alloys of the Pb-Bi system with hypo-eutectic composition have been investigated.

Sign in / Sign up

Export Citation Format

Share Document