scholarly journals EXTRACTION AND EVALUATION OF OIL FROM GREEN ALGAE CLADOPHORA GLOMERATA BY HEXANE/ETHER MIXTURE

2020 ◽  
Vol 60 (2) ◽  
pp. 169-174 ◽  
Author(s):  
Adeyinka Sikiru Yusuff ◽  
Donatus Ewere
Keyword(s):  
Particle Size ◽  
Solvent Extraction ◽  
Physicochemical Properties ◽  
Green Algae ◽  
Profile Analysis ◽  
Group Analysis ◽  
Solvent Ratio ◽  
Cladophora Glomerata ◽  
Extraction Temperature ◽  
Algae Biomass

The overall aim of this study was to grow green algae <em>Cladophora glomerata</em>, extract oil from it, and characterize the extracted oil to gain insight into its physicochemical properties. The effects of parameters affecting the solvent extraction process, temperature, time and biomass particle size were investigated at a fixed solvent ratio of 4:1 hexane to ether. An optimization of oil separation from algae biomass via the solvent extraction method was studied. The obtained results showed that at the extraction temperature of 60 oC, extraction time of 2.5 h, and the particle size of ≤0.6 mm, the maximum oil yield was 18.3% from the process. The functional group analysis revealed the presence of alkane, esters, carboxylic acid, and unsaturated groups on the extracted oil, while the result from the fatty acid profile analysis confirmed the dominance of oleic acid. The physicochemical properties of the extracted algal oil conformed to the ASTM standard.

A Study on the Investigation of Diffusion Coefficient for Oil Extraction from Terebinth (Pistacia terebinthus L.) Seeds

2020 ◽  
Vol 10 (2) ◽  
pp. 144-153
Author(s):  
Fatih Kaya ◽  
Ahmet Özer
Keyword(s):  
Particle Size ◽  
Diffusion Coefficients ◽  
Initial Conditions ◽  
Extraction Process ◽  
Oil Extraction ◽  
Extraction Yield ◽  
Extraction Time ◽  
Solvent Ratio ◽  
Extraction Temperature ◽  
Pistacia Terebinthus

Objective: In this study, the extraction of oil from Pistacia terebinthus L’s seeds grown in Elazig-TURKEY and called menengic in domestic region was investigated. Crude oil content of the seeds obtained from this region was determined as approximately 47% (w/w). Methods: Effects of the parameters such as extraction time, temperature, seeds/solvent ratio (dosage), the particle size of seeds and type of solvent were examined on the oil extraction yield. In this context, it has concluded that up to a certain point, the extraction time has increased the yield of oil extracted. But the extraction temperature showed activity as depending on the solvent type. Results: As expected, it has been observed that the yield of oil has decreased depending on the increase in particle size and dosage as well. The mathematical model obtained by solving Fick's second law under the appropriate boundary and initial conditions were used to calculate diffusion coefficients for the extraction process. Diffusion coefficients for the seeds with a particle size of 0.55 mm were found to be between 1.15x10-11 and 1.86x10-11 m2s-1. To compare the extraction yield of Pistacia terebinthus L’s seeds with that of sunflower at the same conditions, the diffusion coefficients of sunflower seeds were calculated in the range of 9.11x10-12 and 1.13x10-11 m2s-1. Conclusion: These figures show that the diffusion coefficients calculated for both oily seeds are nearly equivalent to each other. The fatty acid composition of extracted oil from Pistacia terebinthus L’s seeds was determined by GC-FID. The GC-FID results showed that oleic, linoleic (ω-6) and palmitic acid were main fatty acids in the oil obtained from menengic seeds.

scholarly journals Solvent Extraction of Jatropha Oil for Biodiesel Production: Effects of Solvent-to-Solid Ratio, Particle Size, Type of Solvent, Extraction Time, and Temperature on Oil Yield

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Justin W. Ntalikwa
Keyword(s):  
Particle Size ◽  
Solvent Extraction ◽  
Oil Recovery ◽  
Quality Parameters ◽  
Biodiesel Production ◽  
Extraction Time ◽  
Oil Yield ◽  
Extraction Temperature ◽  
Jatropha Oil ◽  
Solid Ratio

The aim of this study was to examine the effects of solvent-to-solid ratio, particle size, extraction time, and temperature on the extraction of Jatropha oil using three organic solvents, i.e., n-hexane, petroleum ether, and ethanol. The Soxhlet extraction method was used, and the parameters were varied in the following ranges: extraction temperature of 24–80°C, extraction time of 2 to 8 h, solvent-to-solid ratio of 4 : 1 to 7 : 1, and particle size of 0.5–0.8 mm. After obtaining optimal conditions, a large volume of Jatropha oil was prepared, purified, and subjected to analysis of quality parameters. It was found that the oil content of the Jatropha curcas L. seeds used was 48.2 ± 0.12% w/w. The highest oil yield of 47.5 ± 0.11% w/w corresponding to an oil recovery of 98.6 ± 0.3% w/w was obtained with n-hexane under the following conditions: solvent-to-solid ratio of 6 : 1, particle size of 0.5–0.8 mm, extraction time of 7 h, and extraction temperature of 68°C. This was followed by that of petroleum ether (46.2 ± 0.15% w/w) and lastly by ethanol (43 ± 0.18% w/w). The quality parameters of the oil extracted compared favorably well with most of the values reported in the literature, suggesting that the oil was of good quality for biodiesel production. Environmental and safety concerns over the use of hexane pose a great challenge. Thus, ethanol, which is environmentally benign, is recommended for application. The conditions for ethanol extraction that gave high oil yield were as follows: extraction temperature of 70°C, extraction time of 7 h, solvent-to-solid ratio of 6 : 1, particle size of 0.5–0.8 mm, and oil yield of 43 ± 0.18% w/w corresponding to an oil recovery of 89.2 ± 0.4% w/w.

Wastewater Treatment Using Marine Algae Biomass as Pollutants Removal

2018 ◽  
Vol 69 (5) ◽  
pp. 1089-1098
Author(s):  
Elena Suzana Biris Dorhoi ◽  
Maria Tofana ◽  
Simona Maria Chis ◽  
Carmen Elena Lupu ◽  
Ticuta Negreanu Pirjol
Keyword(s):  
Wastewater Treatment ◽  
Green Algae ◽  
Marine Algae ◽  
Tap Water ◽  
Ulva Lactuca ◽  
Raw Material ◽  
Bioactive Substances ◽  
Algae Biomass ◽  
Marine Biomass ◽  
Pollutants Removal

The valorification of the marine biomass is an important resource for many industries like pharmaceutical, supplying raw material for the extraction of bioactive substances (vitamins, sterols and collagen), cosmetics, biofertilizers and wastewater treatment. In the last years a special attention has been given to the use of macroalgae. The aim of this study was to emphasize the capacity of two representative green algae species frequent presents on the Romanian shore, Ulva lactuca (L.) and Cladophora vagabunda (L.) Hoek, to remove two usual detergents from wastewater. The green algae washed, dried at room temperature, macerated to powder were introduced into different filter paper for comparison, then immersed in waste water treated with different concentrations of detergents. Tap water was used for the experiment. The results show that Ulva lactuca (L.) species is suitable than Cladophora vagabunda (L.) Hoek species, for wastewater treatment.

scholarly journals Physicochemical factors affecting the wettability of copper mine blasting dust

2021 ◽  
Author(s):  
Longzhe Jin ◽  
Jianguo Liu ◽  
Jingzhong Guo ◽  
Jiaying Wang ◽  
Tianyang Wang
Keyword(s):  
Particle Size ◽  
Physicochemical Properties ◽  
Pore Structure ◽  
Total Pore Volume ◽  
Open Pit ◽  
X Rays ◽  
Factors Affecting ◽  
Copper Mine ◽  
Mineral Components ◽  
Hydrophobic Component

AbstractTo investigate the factors affecting the wettability of copper mine blasting dust, the primary blasting dust was collected from an open-pit copper mine and separated into hydrophilic blasting dust (HLBD) and hydrophobic blasting dust (HBBD) using water flotation method. The physicochemical properties of HLBD and HBBD were measured and compared with each other. The properties included particle size distributions (PSDs), micromorphologies, pore structures, mineral components and surface organic carbon functional groups. The results show that particle size and pore structure of the blasting dust are the main factors affecting its wettability. Specifically, particle size of HBBD is smaller than that of HLBD, and their respiratory dust (less than 10 µm) accounts for 61.74 vol% and 53.00 vol%, respectively. The pore structure of HBBD is more developed, and the total pore volume of HBBD is 1.66 times larger than that of HLBD. The identical mineral compositions were detected in HLBD and HBBD by X-rays diffraction (XRD); however, the surface organic hydrophobic component of HBBD is slightly larger than that of HLBD, this may be the reason for the poor wettability of HBBD. This study is significant to understand the effects of physicochemical properties of copper mine blasting dust on its wettability.

Effect of Particle Size on the Oil Yield and Catechin Compound Using Accelerated Solvent Extraction

2013 ◽  
Vol 60 (1) ◽  
Author(s):  
Mohd Azizi Che Yunus ◽  
Manzurudin Hasan ◽  
Norasikin Othman ◽  
Siti Hamidah Mohd-Setapar ◽  
Liza Md.-Salleh ◽  
...  
Keyword(s):  
Particle Size ◽  
Solvent Extraction ◽  
Accelerated Solvent Extraction ◽  
Extraction Time ◽  
Oil Yield ◽  
Particle Sizes ◽  
Experimental Range ◽  
Areca Catechu ◽  
Effect Of Particle Size ◽  
Extraction Cycle

Kajian ini bertujuan untuk mengkaji kesan saiz zarah ke atas pengekstrakan sebatian catechin daripada biji Areca catechu L. dengan menggunakan Pengekstrakan Pelarut Terpecut (PPT). Saiz zarah biji Areca catechu dipelbagaikan dari 75 μm sehingga 500 μm. Pengekstrakan telah dijalankan padaparameter tetap iaitu suhu (140oC), tekanan (1500 psi), masa (10 minit), isipadu semburan (60%) dan satu kitaran pengekstrakan, masing-masing. Hasil minyak peratusan yang lebih tinggi adalah 300 mg minyak / gram sampel (30.00% pati minyak) ditemui pada 125 μm. Walaubagaimanapun, kandungan catechin dalam pati minyak hanya 0.0375 mg catechin / gram sampel. Saiz zarah yang terbaik dalam julat uji kaji ini telah dikenal pasti pada 500 μm yang memberikan kandungan catechin yang tinggi iaitu 0.0515 mg catechin / gram sampel dari 247.5 mg minyak / gram sampel (24.75% pati minyak). Kata kunci: Saiz zarah; catechin; LC-MS-TOF; pengekstrakan pelarut terpecut The purpose of this work is to investigate the effects of particle size on the extraction of catechincompound from Areca catechu L. seeds by using Accelerated Solvent Extraction (ASE). The particle sizes of Areca catechu L. seeds are varied from 75 µm until 500 µm. The extraction is conducted at fixed parameters which are temperature (140oC), pressure (1500 psi), extraction time (10 minutes), flush volume (60%) and the static cycle is done for 1 extraction cycle respectively. Higher percentage oil yield of 300mg oil/gram of sample (30.00% oil yield) is found at 125 µm. However, the amount of catechin in oil yields is only 0.0375 mg of catechin/gram of sample. The best of particle size within the experimental range has been identified at 500 µm which gives a high content of catechin with 0.0515 mg Catechin/gram of sample from 247.5 mg oil/gram of sample (24.75% oil yield). Keywords: Particle size; catechin; LC-MS-TOF; accelerated solvent extraction

scholarly journals CHEMICAL INVESTIGATIONS ON THE ACTIVE PRINCIPLES OF THE PHENOMENON OF LOCAL SKIN REACTIVITY TO BACTERIAL FILTRATES

1938 ◽  
Vol 67 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Gregory Shwartzman ◽  
S. A. Morell
Keyword(s):  
Particle Size ◽  
Physicochemical Properties ◽  
Ammonium Sulfate ◽  
Culture Filtrate ◽  
Active Materials ◽  
Local Skin ◽  
Skin Reactivity ◽  
Average Porosity ◽  
Active Substances ◽  
Capillary Analysis

Several physicochemical properties of the active principles of the phenomenon of local skin reactivity to bacterial filtrates have been investigated. Ultrafiltration through Zsigmondy filters of graded porosities has shown that the active substances are retained by membranes finer than 100 to 120 seconds, whereas coarser ones readily permit their passage. The average porosity of this filtration end-point represents a particle size of about 50 to 100 mµ. When fractionally precipitated with ammonium sulfate, most of the activity of a culture filtrate was concentrated in the two-thirds saturated portion. Isoelectric properties were studied by means of capillary analysis and cataphoresis. At pH 3.0 and below, the substances suspended in the culture filtrates migrated to the cathode; activity in this chamber, however, could not be demonstrated. At pH 4.0 and above, reversal to the anode occurred, as the active materials became negatively charged and readily migrated to this chamber. The isoelectric point, therefore, was considered to be between pH 3.0 and 4.0. Preliminary experiments on adsorption, extraction, and pH stability have been described.

Friendship Group Composition and Juvenile Institutional Misconduct

2016 ◽  
Vol 61 (2) ◽  
pp. 191-209 ◽  
Author(s):  
Shannon E. Reid
Keyword(s):  
Risk Factors ◽  
Latent Profile Analysis ◽  
Profile Analysis ◽  
Group Analysis ◽  
Individual Characteristics ◽  
Incarcerated Youth ◽  
Individual Risk ◽  
Friendship Networks ◽  
Institutional Misconduct ◽  
Latent Profile

The present study examines both the patterns of friendship networks and how these network characteristics relate to the risk factors of institutional misconduct for incarcerated youth. Using friendship networks collected from males incarcerated with California’s Division of Juvenile Justice (DJJ), latent profile analysis was utilized to create homogeneous groups of friendship patterns based on alter attributes and network structure. The incarcerated youth provided 144 egocentric networks reporting 558 social network relationships. Latent profile analysis identified three network profiles: expected group (67%), new breed group (20%), and model citizen group (13%). The three network profiles were integrated into a multiple group analysis framework to examine the relative influence of individual-level risk factors on their rate of institutional misconduct. The analysis finds variation in predictors of institutional misconduct across profile types. These findings suggest that the close friendships of incarcerated youth are patterned across the individual characteristics of the youth’s friends and that the friendship network can act as a moderator for individual risk factors for institutional misconduct.

scholarly journals Dehumidified Air-Assisted Spray-Drying of Cloudy Beetroot Juice at Low Temperature

2021 ◽  
Vol 11 (14) ◽  
pp. 6578
Author(s):  
Aleksandra Jedlińska ◽  
Alicja Barańska ◽  
Dorota Witrowa-Rajchert ◽  
Ewa Ostrowska-Ligęza ◽  
Katarzyna Samborska
Keyword(s):  
Particle Size ◽  
Physicochemical Properties ◽  
Spray Drying ◽  
Low Temperatures ◽  
Beetroot Juice ◽  
Particle Size And Morphology ◽  
Size And Morphology ◽  
Tapped Density ◽  
Lower Loss ◽  
Better Than

This paper discusses the physicochemical properties of powders obtained by spray drying of cloudy beetroot juice, using dehumidified air in variants with or without carriers. The inlet air temperature was 130 °C or 90 °C, and the addition of the carriers was at a ratio of juice to carrier solids of 3:2. In the obtained powders, the following physicochemical properties were determined: water content and water activity, apparent density, loose and tapped density, porosity, flowability, particle size and morphology, and the content and retention of betalains. It was possible to dry cloudy beetroot juice without the use of carriers at low temperatures (90 or 130 °C). The 100% beetroot powders were characterized by satisfactory physicochemical properties, often better than those with carriers (including lower hygroscopicity and higher color saturation and yield). A lower loss of betalains was found for the powders with the addition of carriers. The best process yields were obtained for the powder without carriers at 130 °C and 90 °C.

scholarly journals PEMISAHAN ION KROM(III) DAN KROM(IV) DALAM LARUTAN DENGAN MENGGUNAKAN BIOMASSA ALGA HIJAU SPIROGYRA SUBSALSA SEBAGAI BIOSORBEN

REAKTOR ◽  
2014 ◽  
Vol 15 (1) ◽  
pp. 27
Author(s):  
M Mawardi ◽  
Edison Munaf ◽  
Soleh Kosela ◽  
Widayanti Wibowo
Keyword(s):  
Green Algae ◽  
Metal Ion ◽  
Algal Biomass ◽  
Absorption Capacity ◽  
Ion Concentration ◽  
Phosphorus Compounds ◽  
Time Interval ◽  
Algae Biomass ◽  
Isotherm Equation ◽  
Green Algal

Karakteristik pemisahan ion Cr3+ dan Cr6+ dalam larutan melalui proses biosorpsi menggunakan biomassa alga hijau Spirogyra subsalsa dengan sistem batch telah diteliti. Dalam pelaksanaannya diawali dengan melakukan analisis kualitatif gugus fungsi dalam biomassa menggunakan instrumen FTIR, kemudian dipelajari karakteristik pengaruh variabel pH awal larutan, ukuran partikel biosorben, kecepatan pengadukan, pengaruh pemanasan biosorben, laju penyerapan, pengaruh konsentrasi larutan ion logam terhadap kapasitas serapan biomassa alga. Berdasarkan spektra spektroskopi FTIR dapat disimpulkan bahwa  biomassa alga hijau S. Subsalsa mengandung gugus-gugus karboksilat, amina, amida, amino, karbonil dan hidroksil, disamping adanya senyawa silikon, belerang dan fosfor. Hasil penelitian yang diperoleh  memperlihatkan bahwa kapasitas biosorpsi sangat dipengaruhi oleh pH larutan, waktu kontak dan konsentrasi awal larutan. Biosorpsi optimum kation Cr3+ terjadi pada pH 4,0 sedangkan ion Cr6+ terjadi pada pH 2,0 kemudian berkurang dejalan dengan naiknya pH larutan. Perhitungan dengan persamaan Isoterm Langmuir diperoleh data kapasitas serapan maksimum biomassa alga S. subsalsa untuk masing-masing ion Cr3+ dan Cr6+ adalah 1,82 mg (0,035 mmol) dan 1,51 mg (0,029 mmol) per gram biomassa kering. Kinetika biosorpsi berlangsung relatif cepat, dimana selama selang waktu 30 menit, masing-masing ion terserap sekitar 95,7%; dan 86,5%. Daya serap biomassa juga dipengaruhi kecepatan pengadukan, sedangkan faktor ukuran partikel dan pemanasan biosorben kurang mempengaruhi daya serap biomassa. Key Word : biosorpsi, spirogyra subsalsa, krom(III), krom(VI), sistem batchAbstract Separation of Ion Chromium(III) and Chromium(IV) In Solution Using Green Algae Biomass Spirogyra subsalsa as Biosorbent. The characteristics of Cr3+andCr6+ ion separation in solution through biosorption process using green algal biomass Spirogyrasubsalsa with batch systems have been investigated. The study began with aqualitative analysis of functional groups in biomass using FTIR instrument, then followed by a study of the characteristics of influences by several variables, such as: the initial pH of the solution,the size of biosorben particles, stirring speed, the effect of heating the biosorben, the rate of absorption, and the effect of metal ion concentration in solution on the absorption capacity of algal biomass. Based on FTIR spectroscopy spectra gave a conclusion that biomass of green algae S.subsalsa contains carboxylate groups, amine, amide, amino, carbonyl and hydroxyl, in addition to silicon, sulfur, and phosphorus compounds. The results showed that the biosorption capacity was strongly influenced by pH, contact time, and initial concentration ofthe solution. The optimum biosorption of Cr3+cation occurred at pH 4.0 while that of Cr6+ions occurred at pH 2.0 and then decreased with the increasing pH of solution. The calculation of Langmuir isotherm equation showed that the maximum absorption capacity of algal biomass S.subsalsa for Cr3+and Cr6+ ion respectively was 1.82mg (0.035 mmol) and 1.51 mg (0.029 mmol) pergram of dry biomass. The kinetics of biosorption took place relatively quick, in which during the 30minutes time interval, each ion was absorbed approximately 95.7%; and 86.5%. The absorptive capacity of biomass was also influenced by stirring speed, while the size of particles and heating biosorben gave lessinfluence to the absorption of biomass.

Sign in / Sign up

Export Citation Format

Share Document