scholarly journals Design and Implementation of Software Program based on Web for Basic Electronic Circuit Practice

2015 ◽  
Vol 7 (2) ◽  
pp. 113-117
Author(s):  
Young-joo Lee ◽  
Joon-won Hwang ◽  
Dae-min Hwang ◽  
Kyung-min Yun ◽  
Bo-Gon Lee ◽  
...  
Keyword(s):  
Electronic Circuit ◽  
Design And Implementation ◽  
Software Program

Design and Implementation of Portable Intelligent LCF Measuring Instrument

2014 ◽  
Vol 539 ◽  
pp. 75-78
Author(s):  
Lin Sheng Wang ◽  
Ying Ma ◽  
Xiao Zhi Wang
Keyword(s):  
Electronic Circuit ◽  
Low Cost ◽  
Signal Frequency ◽  
Measuring Instrument ◽  
Design And Implementation ◽  
Expensive Equipment ◽  
Specialized Equipment

In view of it is often needed to measure the value of the inductance capacitance and signal frequency in the welding and the debugging process of the electronic circuit, specialized equipment due to the huge volume of expensive equipment which is difficult to measure, we use SCM to design a portable measuring instrument which have low cost and can measure the value of inductance and capacitance, as well as signal frequency. It can meet the demand of precision after testing, so as to reach requirements for measuring instrument.

BUILDING ELECTRONIC BURSTERS WITH THE MORRIS–LECAR NEURON MODEL

2006 ◽  
Vol 16 (12) ◽  
pp. 3617-3630 ◽  
Author(s):  
ALEXANDRE WAGEMAKERS ◽  
MIGUEL A. F. SANJUÁN ◽  
JOSÉ M. CASADO ◽  
KAZUYUKI AIHARA
Keyword(s):  
Phase Space ◽  
Parameter Space ◽  
Neuron Model ◽  
Electronic Circuit ◽  
Initial Point ◽  
Bifurcation Diagrams ◽  
Design And Implementation ◽  
Bursting Neurons ◽  
Fast Spiking ◽  
Dynamical Features

We propose a method for the design of electronic bursting neurons, based on a simple conductance neuron model. A burster is a particular class of neuron that displays fast spiking regimes alternating with resting periods. Our method is based on the use of an electronic circuit that implements the well-known Morris–Lecar neuron model. We use this circuit as a tool of analysis to explore some regions of the parameter space and to contruct several bifurcation diagrams displaying the basic dynamical features of that system. These bifurcation diagrams provide the initial point for the design and implementation of electronic bursting neurons. By extending the phase space with the introduction of a slow driving current, our method allows to exploit the bistabilities which are present in the Morris–Lecar system to the building of different bursting models.

Design of Remote Control Robot System

2012 ◽  
Vol 619 ◽  
pp. 321-324
Author(s):  
You Jun Huang ◽  
Ze Lun Li ◽  
Zhi Cheng Huang
Keyword(s):  
Remote Control ◽  
Electronic Circuit ◽  
Radio Receiver ◽  
Software System ◽  
Robot System ◽  
Development Platform ◽  
Radio Transmitter ◽  
Remote Operation ◽  
Software Program ◽  
Receiver Module

A remote control robot system is designed, and the operator uses the remote control radio transmitter module for remote operation, and after the radio receiver module receiving the signal, it can control the movements of the robot by the PLC instructions. The software system used STEP 7 Micro WIN SP6 as development platform to prepare the software program, and designed the robot hardware with the use of electronic circuit knowledge. The results show that the remote robot system is successful, and it can complete a variety of actions according to requires.

scholarly journals Design of Electronic Circuit for Mining Explosive Detonator

2021 ◽  
Author(s):  
Adil Elrayah ◽  
Ausabah I.A. Ahmed ◽  
Abdlrasool Jabbar
Keyword(s):  
Mobile Phone ◽  
Work Environment ◽  
Electronic Circuit ◽  
National Standards ◽  
The Other ◽  
C Language ◽  
Computer Monitoring ◽  
Receiver Block ◽  
Software Program ◽  
Monitoring Software

Designing of mining exclusive electronic circuit, safety for work environment is vital and important. The system devices contained transmitter block, which are containing computer monitoring software and internet modem. The other one is receiver block which is included explosive circuit and their components (i.e., a digital component mobile phone, ICs, and detector). To control the operation steps process used software program written with C++ language. The system was successfully built and designed. Besides that, it could capabilities of components set in the designed circuit. Moreover, the circuit and their components were operated carefully according to program sequence. The results are achieved the general objectives of the research. Also, it was match standards, specified in national standards for performances and appearances of such devices.

Design and Implementation of Multi-Protocol Self-Adaptation Gateway

2014 ◽  
Vol 687-691 ◽  
pp. 2108-2111
Author(s):  
Kai Lin Zhang ◽  
Da Hua Li ◽  
Shu Chen Shi ◽  
Xue Song Yang ◽  
Zhen Xiao ◽  
...  
Keyword(s):  
Network Protocols ◽  
It Use ◽  
Design And Implementation ◽  
Hardware Interface ◽  
Software Program ◽  
Self Adaptation ◽  
Profibus Dp

For the four kinds of network protocols which are common in industry :PROFIBUS-DP, DeviceNet, EtherNet/IP and Modbus-RTU, a gateway has been designed which could integrate the four protocols ,and have developed hardware and software program of the Multi-protocol self-adaptation gateway .It uses STM32F407ZGT6 as its major chip. A Modbus-RTU interface has been designed which depends on the UART interface of the main chip to send and receive packets in hardware. It use COMX as hardware interface of PROFIBUS-DP ,DeviceNet ,and EtherNet/IP to process their packets. It has achieved a function that the PROFIBUS-DP interface will change its address with the changing of the configuration of master .In addition, the multi-protocol self-adaptation gateway can integrate several masters which support different protocols in one network. The master controllers could communicate with each other in this network.After being tested and verified ,it has been used in the communication of DCS systems, and it has converted the packets of the four protocols which have been mentioned above and it has met the demands of designing a gateway.

Design and Implementation of Detection System Based on IC

2014 ◽  
Vol 539 ◽  
pp. 70-74
Author(s):  
Lin Jing Wang ◽  
Pei Jiang Zhang
Keyword(s):  
Integrated Circuit ◽  
Electronic Circuit ◽  
Detection System ◽  
Design And Implementation

This paper has introduced a kind of intellectual detection system. Based on electronic circuit, this system which adopts the integrated circuit can realize the following functions: When someone passes in or out, it firstly transmits the signal of transmitting circuit, receives the signal of receiving circuit, and the identification of circuit can record personnel entering or leaving counted by the counter for addition or subtraction. When someone enters, the counter of this system can go on with counting automatically. When someone leaves, it can automatically reduce count. Finally, through BCD-latch /7-segment decoder / driver LED display, we can see that show counting through the monitor.

scholarly journals Design and implementation hamming neural network with VHDL

2020 ◽  
Vol 19 (3) ◽  
pp. 1469
Author(s):  
Liqaa Saadi Mezher
Keyword(s):  
Neural Network ◽  
Block Diagram ◽  
Pure Line ◽  
Simulation Methods ◽  
Diagram Method ◽  
Design And Implementation ◽  
Coding Method ◽  
Software Program ◽  
Positive Line ◽  
Logical Gate

<p>Hamming Neural Network is type of artificial neural network consist of two types of layers (Feed Forward Layers and Recurrent Layer). In this paper, two inputs of patterns in bianary number were used. In the first layer, two neurons and pure line function were used. In the second layer, three neurons and positive line function were used. Also applied Hamming Neural networks algorithm in three simulation methods (Logical gate method, software program coding method and instant block diagram method). In this work in VHDL software program was used and FPGA hardware used.</p>

Sign in / Sign up

Export Citation Format

Share Document