scholarly journals Influence of Twist on Selected Properties of Multifilament Yarn

2018 ◽  
Vol 18 (2) ◽  
pp. 110-120
Author(s):  
Iva Mertová ◽  
Eva Moučková ◽  
Bohuslav Neckář ◽  
Monika Vyšanská
Keyword(s):  
Cross Section ◽  
Fiber Bundle ◽  
Structural Parameters ◽  
Sectional Area ◽  
Fiber Stress ◽  
Cross Sectional ◽  
Yarn Twist ◽  
Section Shape ◽  
Multifilament Yarn ◽  
Multifilament Yarns

Abstract Owing to twisting of filament fiber bundle, the structure and consequently various parameters and properties of a fiber bundle are changed. The aim of the work is to verify the effect of multifilament yarn twist (or twist coefficient) on selected mechanical properties such as multifilament tenacity, breaking elongation, and coefficient of fiber stress utilization in the yarn. Furthermore, the influence of twist on structural parameters such as the angle of peripheral fibers, the packing density, and the substance cross-sectional area of fiber bundle is observed. Two multifilament yarns with different filament cross-section shape and material were used for the experiment. Experimentally obtained data was compared with the known model dependencies derived decades ago based on the helical model. It can be stated that multifilament yarn retraction can be predicted based on the angle of peripheral fibers using the Braschler’s model. The coefficient of fiber stress utilization in the multifilament yarn determined experimentally corresponds with a theoretical curve, constructed according to Gégauff and Neckář, in the area of Koechlin’s twist coefficient α > 54 ktex1/2 m−1. Results as well as possible causes of deviations of experimental data from the theoretical one are discussed in this work.

Online Monitoring of Functional Electrical Properties in Aerosol Jet Printing Additive Manufacturing Process Using Shape-From-Shading Image Analysis

2017 ◽  
Vol 139 (10) ◽  
Author(s):  
Roozbeh (Ross) Salary ◽  
Jack P. Lombardi ◽  
Prahalad K. Rao ◽  
Mark D. Poliks
Keyword(s):  
Cross Section ◽  
Electrical Resistance ◽  
Online Monitoring ◽  
Shape From Shading ◽  
Sectional Area ◽  
Cross Sectional ◽  
Jet Printing ◽  
The Cross ◽  
Aerosol Jet Printing ◽  
Line Resistance

The goal of this research is online monitoring of functional electrical properties, e.g., resistance, of electronic devices made using aerosol jet printing (AJP) additive manufacturing (AM) process. In pursuit of this goal, the objective is to recover the cross-sectional profile of AJP-deposited electronic traces (called lines) through shape-from-shading (SfS) analysis of their online images. The aim is to use the SfS-derived cross-sectional profiles to predict the electrical resistance of the lines. An accurate characterization of the cross section is essential for monitoring the device resistance and other functional properties. For instance, as per Ohm’s law, the electrical resistance of a conductor is inversely proportional to its cross-sectional area (CSA). The central hypothesis is that the electrical resistance of an AJP-deposited line estimated online and in situ from its SfS-derived cross-sectional area is within 20% of its offline measurement. To test this hypothesis, silver nanoparticle lines were deposited using an Optomec AJ-300 printer at varying sheath gas flow rate (ShGFR) conditions. The four-point probes method, known as Kelvin sensing, was used to measure the resistance of the printed structures offline. Images of the lines were acquired online using a charge-coupled device (CCD) camera mounted coaxial to the deposition nozzle of the printer. To recover the cross-sectional profiles from the online images, three different SfS techniques were tested: Horn’s method, Pentland’s method, and Shah’s method. Optical profilometry was used to validate the SfS cross section estimates. Shah’s method was found to have the highest fidelity among the three SfS approaches tested. Line resistance was predicted as a function of ShGFR based on the SfS-estimates of line cross section using Shah’s method. The online SfS-derived line resistance was found to be within 20% of offline resistance measurements done using the Kelvin sensing technique.

scholarly journals Optimization of Geometric Parameters of Thermal Insulation of Pre-Insulated Double Pipes

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1012 ◽  
Author(s):  
Dorota Krawczyk ◽  
Tomasz Teleszewski
Keyword(s):  
Heat Flux ◽  
Heat Conduction ◽  
Cross Section ◽  
Thermal Insulation ◽  
Major Axis ◽  
Heat Losses ◽  
Sectional Area ◽  
Cross Sectional ◽  
Elliptical Shape ◽  
Half Axis

This paper presents the analysis of the heat conduction of pre-insulated double ducts and the optimization of the shape of thermal insulation by applying an elliptical shape. The shape of the cross-section of the thermal insulation is significantly affected by the thermal efficiency of double pre-insulated networks. The thickness of the insulation from the external side of the supply and return pipes affects the heat losses of the double pre-insulated pipes, while the distance between the supply and return pipes influences the heat flux exchanged between these ducts. An assumed elliptical shape with a ratio of the major axis to the minor half axis of an ellipse equaling 1.93 was compared to thermal circular insulation with the same cross-sectional area. All calculations were made using the boundary element method (BEM) using a proprietary computer program written in Fortran as part of the VIPSKILLS project.

Modelling the Acoustical and Airflow Performance of Simple Lined Ventilation Apertures

2005 ◽  
Vol 12 (4) ◽  
pp. 277-292 ◽  
Author(s):  
D J Oldham ◽  
Jian Kang ◽  
M W Brocklesby
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
High Aspect Ratio ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Cross Sectional ◽  
Ventilation Performance ◽  
Acoustic Treatment

The pressure differences that can be used to drive a natural ventilation system are very small and thus large apertures are required to allow sufficient air to enter and leave a building to ensure good air quality or thermal comfort. Large apertures are potential acoustic weak points on a façade and may require some form of acoustic treatment such as absorbent linings, in which case the ventilator is similar to a short section of lined duct. In ducts, the performance of absorbent linings increases with the length of lining and the ratio of the length of lined perimeter to the cross sectional area of the duct. Thus, for a duct of a given cross sectional area, a lining is more effective for a duct with a high aspect ratio than for a duct with a square cross section. However, the high aspect ratio cross section will result in greater flow resistance and impede the airflow performance. In this paper numerical methods are employed to investigate the effect of different configurations of a lined aperture on the acoustical and ventilation performance of the aperture in order to establish the optimum configurations.

Cross Section Optimization of Plane Truss among Different Spans

2014 ◽  
Vol 679 ◽  
pp. 1-5 ◽  
Author(s):  
Sumayah Abdulsalam Mustafa ◽  
Mohd Zulham Affandi bin Mohd Zahid ◽  
Md.Hadli bin Abu Hassan
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Element Analysis ◽  
Cross Sectional ◽  
Analysis And Design ◽  
Cross Section Shape ◽  
Design Variables ◽  
Section Shape ◽  
Steel Sections ◽  
Research Show

Cross sectional areas optimization is to be implemented to study the influence of the cross section shape on the optimum truss weight. By the aid of analysis and design engines with advanced finite element analysis that is the steel design software STAAD. Four rolled steel sections (angle, tube, channel, and pipe) which are used in industrial roof trusses are applied for comparison. Many previous studies, use the areas of cross sections as design variables without highlight to the shape of cross section at the start of the process, consequently the result area will be adequate if the designer choose the effective shape than others. Results of this research show that the chosen cross section shape has a significant impact on the optimum truss weight for same geometry of truss type under the same circumstances of loading and supports.

Efficiencies for Partially Wetted Spine Fins: Uniform Cross Section, Conical, Concave Parabolic, and Convex Parabolic Spines

2013 ◽  
Vol 135 (8) ◽  
Author(s):  
Worachest Pirompugd ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Cross Section ◽  
Transfer Rate ◽  
Approximate Equation ◽  
Sectional Area ◽  
Cross Sectional ◽  
Fin Efficiency ◽  
Conduction Heat Transfer ◽  
Uniform Cross Section

In this study, efficiencies for partially wetted fins for the uniform cross section spine, conical spine, concave parabolic spine, and convex parabolic spine are presented using an analytical method. Depending on the set of boundary conditions, there are two methods for deriving the efficiencies of partially wet fins for each spine. The eight equations for fin efficiencies were investigated. Fin efficiency is a function of the length of the dry portion. Thus, the equations for calculating the length of the dry portion are also presented. The findings indicate that a larger cross-sectional fin results in a higher conduction heat transfer rate. Contrarily, the fin efficiency is lower. This is different from the longitudinal fin, for which the trend lines of heat transfer rate and fin efficiency are the same. This converse relationship is due to the effect of the ratio of the cross-sectional area to the surface area. Moreover, partially wet fin efficiencies decrease with increased relative humidity. For convenience, the approximate equation for efficiencies for partially wet fins, which is derived from the equations for fully wet and fully dry fin efficiencies, is also presented.

scholarly journals Numerical simulation of cutting layer in internal corners milling

Mechanik ◽  
2019 ◽  
Vol 92 (7) ◽  
pp. 412-414
Author(s):  
Jan Burek ◽  
Rafał Flejszar ◽  
Barbara Jamuła
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Cross Section ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Cross Sectional ◽  
Cross Section Area ◽  
Section Area ◽  
The Cross ◽  
The Stability

The analytical and numerical model of the cross-section of the machined layer in the process of milling of concave rounding is presented. Simulation tests were carried out to determine the cross-sectional area of the cutting layer. A strategy has been developed that allows to increase the stability of the cross-section area of the cutting layer when the mill enters the inner corner area.

Normalization of force generated by canine airway smooth muscles

1991 ◽  
Vol 260 (6) ◽  
pp. L522-L529 ◽  
Author(s):  
H. Jiang ◽  
A. J. Halayko ◽  
K. Rao ◽  
P. Cunningham ◽  
N. L. Stephens
Keyword(s):  
Smooth Muscle ◽  
Cross Section ◽  
Cross Sections ◽  
Smooth Muscles ◽  
Muscle Cells ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Cross Sectional ◽  
Muscle Stress ◽  
Total Tissue

A variety of normalizations have been employed to compare maximal isometric force (Po) produced by smooth muscles at different locations and stages of maturation. Because these procedures have not always been based on rigorous principles, confusion has resulted. To obtain a less ambiguous index of force production, we measured in vitro Po from mongrel canine tracheal (TSM) and bronchial (BSM) smooth muscle with an electromagnetic lever and normalized it to force per unit cross-sectional area of whole tissue (tissue stress), to force per unit cross-sectional area of muscle in the cross section of total tissue (muscle stress), and to force per fractional unit of myosin in the tissue cross section (myosin stress). Proportion of myosin in cross-sectional area of tissue was deduced from data obtained by sodium dodecyl sulfate gel electrophoresis of crude muscle extracts. For TSM, tissue stress was 1.499 X 10(5) N/m2 +/- 0.1 (SE), whereas it was only 0.351 X 10(5) N/m2 +/- 0.05 (SE) for BSM, representing a 4.27-fold difference (P less than 0.01). There was a 1.60-fold difference (P less than 0.05) in muscle stress, which was correlated to the morphometric finding that 79 +/- 1.4% (SE) of the tracheal strip cross section was muscle, whereas only 30 +/- 1.0% (SE) of bronchial tissue was occupied by muscle. Average myosin content was the same in smooth muscle cells of TSM and BSM, indicating that total amount of myosin in tissue cross sections was essentially a function of proportional area of muscle cells in total tissue cross sections.(ABSTRACT TRUNCATED AT 250 WORDS)

Optimization Design of an Efficient Evacuator for Gun Barrels

2021 ◽  
Author(s):  
Quanzhao Sun ◽  
Li Chen ◽  
Jie Zhang ◽  
Yanming Song ◽  
Guolai Yang ◽  
...  
Keyword(s):  
Optimization Design ◽  
Structural Parameters ◽  
Cross Sectional Area ◽  
Main Function ◽  
Sectional Area ◽  
Working Process ◽  
Cross Sectional ◽  
Mathematical Expressions ◽  
Reliability Indicator ◽  
The Cross

Abstract Evacuators are key components of gun barrels, and their main function is to drain the gunpowder gas remaining in the gun bore from the muzzle by ejection. To design an efficient evacuator for the gun barrels, an optimization model with the mathematical expressions describing the working process of the evacuator was established. The four structural parameters that affect the efficiency of the evacuator, including the volume of the gas storage cylinder chamber, the distance of the nozzle from the muzzle end face, the cross-sectional area of the nozzles and the cross-sectional area of the valves, were optimized. The effective working time and reliability indicator of the optimized evacuator were improved. This work describes a framework for improving the design of highly efficient evacuators on gun barrels.

Corrosion-Induced Concrete Cracking, Steel-Concrete Bond Loss, and Mechanical Degradation of Steel Bars

2014 ◽  
Vol 919-921 ◽  
pp. 1760-1770 ◽  
Author(s):  
Fu Jian Tang ◽  
Gen Da Chen ◽  
Wei Jian Yi
Keyword(s):  
Cross Section ◽  
Crack Width ◽  
Surface Profile ◽  
Concrete Surface ◽  
Cross Sectional Area ◽  
Mechanical Degradation ◽  
Sectional Area ◽  
Cross Sectional ◽  
Steel Bars ◽  
The Cross

This study experimentally investigated corrosion-induced deterioration in reinforced concrete (RC) structures: concrete cover cracking, steel-concrete bond loss, and mechanical degradation of corroded steel bars. Pullout and RC beam specimens were prepared, subjected to accelerated corrosion in a wet sand bath, and tested under loading. A 3D laser scan was employed to measure the surface profile of corroded steel bars and determine the corrosion effect on the distribution of residual cross section area. The crack width on the concrete surface was sampled randomly and analyzed statistically. Corrosion reduced the bond strength between steel bars and concrete, particularly in the form of corrosion-induced number and width of cracks. Both the yield and ultimate strengths depended upon the critical cross sectional area of steel bars, whereas the elongation changed with the cross section distribution over the length of the steel bars. Corrosion also changed the distribution of the cross sectional area of steel bars. The crack width on the concrete surface can be well represented by a normal distribution regardless of corrosion levels.

Sign in / Sign up

Export Citation Format

Share Document