scholarly journals A comparison of experimental results of soot production in laminar premixed flames

2015 ◽  
Vol 5 (1) ◽  
Author(s):  
Nattan R. Caetano ◽  
Diego Soares ◽  
Roger P. Nunes ◽  
Fernando M. Pereira ◽  
Paulo Smith Schneider ◽  
...  
Keyword(s):  
Equivalence Ratio ◽  
Computational Models ◽  
Volume Fraction ◽  
Soot Formation ◽  
Measurement Techniques ◽  
Soot Volume Fraction ◽  
Light Extinction ◽  
Burner Surface ◽  
Experimental Database ◽  
Premixed Laminar

AbstractSoot emission has been the focus of numerous studies due to the numerous applications in industry, as well as the harmful effects caused to the environment. Thus, the purpose of this work is to analyze the soot formation in a flat flame burner using premixed compressed natural gas and air, where these quasi-adiabatic flames have one-dimensional characteristics. The measurements were performed applying the light extinction technique. The air/fuel equivalence ratiowas varied to assess the soot volume fractions for different flame configurations. Soot production along the flamewas also analyzed by measurements at different heights in relation to the burner surface. Results indicate that soot volume fraction increases with the equivalence ratio. The higher regions of the flamewere analyzed in order to map the soot distribution on these flames. The results are incorporated into the experimental database for measurement techniques calibration and for computational models validation of soot formation in methane premixed laminar flames, where the equivalence ratio ranging from 1.5 up to 8.

Soot and PAH Formation Characteristics in a Micro Flow Reactor With a Controlled Temperature Profile

2011 ◽  
Author(s):  
Ryu Tanimoto ◽  
Takuya Tezuka ◽  
Susumu Hasegawa ◽  
Hisashi Nakamura ◽  
Kaoru Maruta
Keyword(s):  
Flow Velocity ◽  
Temperature Profile ◽  
Mole Fraction ◽  
Equivalence Ratio ◽  
Flow Reactor ◽  
Volume Fraction ◽  
Soot Formation ◽  
Soot Volume Fraction ◽  
Low Flow ◽  
Micro Flow

To examine soot and PAH formation processes for rich methane/air and acetylene/air mixtures, a micro flow reactor with a controlled temperature profile was employed. In the experiment for a methane/air mixture, four kinds of responses to the variations of flow velocity and equivalence ratio were observed as follows: soot formation without a flame; a flame with soot formation; a flame without soot formation; and neither flame nor soot formation. Soot formations were observed in low flow velocity and high equivalence ratio. Starting point of soot formation shifted to the upstream side, i.e., low-temperature side, of the micro flow reactor with the decrease of flow velocity. One-dimensional steady-state computation was conducted by a flame code. In high flow velocity, low mole fraction of C2H2 and high mole fraction of OH were observed in the whole region of the micro flow reactor. Soot volume fraction did not increase in this case. On the other hand, in low flow velocity, high mole fraction of C2H2 and low mole fraction of OH were observed at the downstream side of the micro flow reactor. Soot volume fraction increased in this case. Since significant soot formation was observed at the low flow velocity and the high equivalence ratio, experiments with gas sampling were conducted for acetylene/air mixture to investigate temperature and equivalence ratio dependence of soot precursor production in such condition. Volume fractions of benzene increased with an increase of temperature. They were larger at higher equivalence ratio at the same temperature. Volume fractions of styrene increased with an increase of temperature. They were larger at higher equivalence ratio when the temperature is less than 1000 K. However the tendency was changed at 1000 K, styrene volume fraction at equivalence ratio of 7.0 was larger than that at equivalence ratio of 8.0.

Modelling Soot Formation in Aviation Fuel Oxidation

2006 ◽  
Author(s):  
A. G. Kyne ◽  
M. Pourkashanian ◽  
C. W. Wilson
Keyword(s):  
Residence Time ◽  
Equivalence Ratio ◽  
Volume Fraction ◽  
Soot Formation ◽  
Soot Volume Fraction ◽  
Chemical Kinetic ◽  
Reaction Model ◽  
Aviation Fuel ◽  
Out Of Sample ◽  
The Impact

This study outlines the development of a new chemical kinetic surrogate aviation fuel air reaction mechanism which models up to four ring Polycyclic Aromatic Hydrocarbon (PAH) growth. A sensitivity analysis has been conducted to guide us in improving the correlation with modelled and measured species’ profiles in an n-decane – air combustion environment. It was reassuring that the mechanism could be successfully applied to an out of sample set of experimental profiles for acetylene combustion and showed a noticeable improvement over a previous reaction model. In order to calculate the soot volume fraction, a previously developed soot model was employed that accounts for soot particle coagulation, aggregation and surface growth. The impact of pressure, equivalence ratio and residence time on soot formation for a surrogate aviation fuel-air combustion in a Perfectly Stirred Reactor was also investigated. Generally speaking, the level of soot increased with increasing pressure, residence time and equivalence ratio.

scholarly journals Effect of the Preheated Oxidizer Temperature on Soot Formation and Flame Structure in Turbulent Methane-Air Diffusion Flames at 1 and 3 atm: A CFD Investigation

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3671
Author(s):  
Subrat Garnayak ◽  
Subhankar Mohapatra ◽  
Sukanta K. Dash ◽  
Bok Jik Lee ◽  
V. Mahendra Reddy
Keyword(s):  
Mole Fraction ◽  
Air Temperature ◽  
Reaction Rate ◽  
Volume Fraction ◽  
Diffusion Flames ◽  
Soot Formation ◽  
Flame Structure ◽  
Soot Volume Fraction ◽  
Computational Domain ◽  
Pressure Elevation

This article presents the results of computations on pilot-based turbulent methane/air co-flow diffusion flames under the influence of the preheated oxidizer temperature ranging from 293 to 723 K at two operating pressures of 1 and 3 atm. The focus is on investigating the soot formation and flame structure under the influence of both the preheated air and combustor pressure. The computations were conducted in a 2D axisymmetric computational domain by solving the Favre averaged governing equation using the finite volume-based CFD code Ansys Fluent 19.2. A steady laminar flamelet model in combination with GRI Mech 3.0 was considered for combustion modeling. A semi-empirical acetylene-based soot model proposed by Brookes and Moss was adopted to predict soot. A careful validation was initially carried out with the measurements by Brookes and Moss at 1 and 3 atm with the temperature of both fuel and air at 290 K before carrying out further simulation using preheated air. The results by the present computation demonstrated that the flame peak temperature increased with air temperature for both 1 and 3 atm, while it reduced with pressure elevation. The OH mole fraction, signifying reaction rate, increased with a rise in the oxidizer temperature at the two operating pressures of 1 and 3 atm. However, a reduced value of OH mole fraction was observed at 3 atm when compared with 1 atm. The soot volume fraction increased with air temperature as well as pressure. The reaction rate by soot surface growth, soot mass-nucleation, and soot-oxidation rate increased with an increase in both air temperature and pressure. Finally, the fuel consumption rate showed a decreasing trend with air temperature and an increasing trend with pressure elevation.

Analytical Formulation-Based Soot Modelling in Ethylene Laminar Jet Diffusion Flames

2021 ◽  
Author(s):  
Amit Makhija ◽  
Krishna Sesha Giri
Keyword(s):  
Volume Fraction ◽  
Diffusion Flames ◽  
Soot Formation ◽  
Mixture Fraction ◽  
Soot Volume Fraction ◽  
Smoke Point ◽  
Computational Time ◽  
Detailed Model ◽  
Conservation Equations ◽  
Oxidation Rates

Abstract Soot volume fraction predictions through simulations carried out on OpenFOAM® are reported in diffusion flames with ethylene fuel. A single-step global reaction mechanism for gas-phase species with an infinitely fast chemistry assumption is employed. Traditionally soot formation includes inception, nucleation, agglomeration, growth, and oxidation processes, and the individual rates are solved to determine soot levels. However, in the present work, the detailed model is replaced with the soot formation and oxidation rates, defined as analytical functions of mixture fraction and temperature, where the net soot formation rate can be defined as the sum of individual soot formation and oxidation rates. The soot formation/oxidation rates are modelled as surface area-independent processes. The flame is modelled by solving conservation equations for continuity, momentum, total energy, and species mass fractions. Additionally, separate conservation equations are solved to compute the mixture fraction and soot mass fraction consisting of source terms that are identical and account for the mixture fraction consumption/production due to soot. As a consequence, computational time can be reduced drastically. This is a quantitative approach that gives the principal soot formation regions depending on the combination of local mixture fraction and temperature. The implemented model is based on the smoke point height, an empirical method to predict the sooting propensity based on fuel stoichiometry. The model predicts better soot volume fraction in buoyant diffusion flames. It was also observed that the optimal fuel constants to evaluate soot formation rates for different fuels change with fuel stoichiometry. However, soot oxidation strictly occurs in a particular region in the flame; hence, they are independent of fuel. The numerical results are compared with the experimental measurements, showing an excellent agreement for the velocity and temperature. Qualitative agreements are observed for the soot volume fraction predictions. A close agreement was obtained in smoke point prediction for the overventilated flame. An established theory through simulations was also observed, which states that the amount of soot production is proportional to the fuel flow rate. Further validations underscore the predictive capabilities. Model improvements are also reported with better predictions of soot volume fractions through modifications to the model constants based on mixture fraction range.

scholarly journals The influence of aliphatics on soot inception modelling

2021 ◽  
Author(s):  
Nemanja Ceranic
Keyword(s):  
Volume Fraction ◽  
Diffusion Flames ◽  
Soot Formation ◽  
Fluid Dynamic ◽  
Soot Volume Fraction ◽  
Surface Reactivity ◽  
Complex Nature ◽  
Laminar Diffusion Flames ◽  
Laminar Diffusion ◽  
Polycyclic Aromatic

Soot models have been investigated for several decades and many fundamental models exist that prescribe soot formation in agreement with experiments and theories. However, due to the complex nature of soot formation, not all pathways have been fully characterized. This work has numerically studied the influence that aliphatic based inception models have on soot formation for coflow laminar diffusion flames. CoFlame is the in-house parallelized FORTRAN code that was used to conduct this research. It solves the combustion fluid dynamic conservation equations for a variety of coflow laminar diffusion flames. New soot inception models have been developed for specific aliphatics in conjunction with polycyclic aromatic hydrocarbon based inception. The purpose of these models was not to be completely fundamental in nature, but more so a proof-of-concept in that an aliphatic based mechanism could account for soot formation deficiencies that exist with just PAH based inception. The aliphatic based inception models show potential to enhance predicative capability by increasing the prediction of the soot volume fraction along the centerline without degrading the prediction along the pathline of maximum soot. Additionally, the surface reactivity that was used to achieve these results lied closer in the range of numerically derived optimal values as compared to the surface reactivity that was needed to match peak soot concentrations without the aliphatic based inception models.

Prediction of Soot Formation Trends in Turbulent Kerosene-Air Diffusion Jet Flames With Elevated Operating Pressure

2017 ◽  
Author(s):  
Pravin Nakod ◽  
Saurabh Patwardhan ◽  
Ishan Verma ◽  
Stefano Orsino
Keyword(s):  
Environmental Protection Agency ◽  
Volume Fraction ◽  
Soot Formation ◽  
Mixture Fraction ◽  
Soot Volume Fraction ◽  
Operating Pressure ◽  
Jet Flames ◽  
Emission Standard ◽  
Radial Profiles ◽  
Air Diffusion

Emission standard agencies are coming up with more stringent regulations on soot, given its adverse effect on human health. It is expected that Environmental Protection Agency (EPA) will soon place stricter regulations on allowed levels of the size of soot particles from aircraft jet engines. Since, aircraft engines operate at varying operating pressure, temperature and air-fuel ratios, soot fraction changes from condition to condition. Computation Fluid Dynamics (CFD) simulations are playing a key role in understanding the complex mechanism of soot formation and the factors affecting it. In the present work, soot formation prediction from numerical analyses for turbulent kerosene-air diffusion jet flames at five different operating pressures in the range of 1 atm. to 7 atm. is presented. The geometrical and test conditions are obtained from Young’s thesis [1]. Coupled combustion-soot simulations are performed for all the flames using steady diffusion flamelet model for combustion and Mass-Brookes-Hall 2-equation model for soot with a 2D axisymmetric mesh. Combustion-Soot coupling is required to consider the effect of soot-radiation interaction. Simulation results in the form of axial and radial profiles of temperature, mixture fraction and soot volume fraction are compared with the corresponding experimental measured profiles. The results for temperature and mixture fraction compare well with the experimental profiles. Predicted order of magnitude and the profiles of the soot volume fraction also compare well with the experimental results. The correct trend of increasing the peak soot volume fraction with increasing the operating pressure is also captured.

A Numerical Study on the Influence of Hydrogen Addition on Soot Formation in a Laminar Aviation Kerosene (Jet A1) Flame at Elevated Pressure

2021 ◽  
Author(s):  
Mingshan Sun ◽  
Zhiwen Gan
Keyword(s):  
Volume Fraction ◽  
Soot Formation ◽  
Laminar Flame ◽  
Numerical Study ◽  
Soot Volume Fraction ◽  
Elevated Pressure ◽  
Condensation Process ◽  
Hydrogen Addition ◽  
Aviation Kerosene ◽  
Soot Precursor

Abstract The hydrogen addition is a potential way to reduce the soot emission of aviation kerosene. The current study analyzed the effect of hydrogen addition on aviation kerosene (Jet A1) soot formation in a laminar flame at elevated pressure to obtain a fundamental understanding of the reduced soot formation by hydrogen addition. The soot formation of flame was simulated by CoFlame code. The soot formation of kerosene-nitrogen-air, (kerosene + replaced hydrogen addition)-nitrogen-air, (kerosene + direct hydrogen addition)-nitrogen-air and (kerosene + direct nitrogen addition)-nitrogen-air laminar flames were simulated. The calculated pressure includes 1, 2 and 5 atm. The hydrogen addition increases the peak temperature of Jet A1 flame and extends the height of flame. The hydrogen addition suppresses the soot precursor formation of Jet A1 by physical dilution effect and chemical inhibition effect, which weaken the poly-aromatic hydrocarbon (PAH) condensation process and reduce the soot formation. The elevated pressure significantly accelerates the soot precursor formation and increases the soot formation in flame. Meanwhile, the ratio of reduced soot volume fraction to base soot volume fraction by hydrogen addition decreases with the increase of pressure, indicating that the elevated pressure weakens the suppression effect of hydrogen addition on soot formation in Jet A1 flame.

Fischer-Tropsch Fuel Characterization via Microturbine Testing and Fundamental Combustion Measurements

2008 ◽  
Author(s):  
A. Srinivasan ◽  
B. Ellis ◽  
J. F. Crittenden ◽  
W. E. Lear ◽  
Brandon Rotavera ◽  
...  
Keyword(s):  
Shock Tube ◽  
Volume Fraction ◽  
Soot Formation ◽  
Soot Volume Fraction ◽  
Jet Fuels ◽  
Synthetic Fuels ◽  
Fischer Tropsch ◽  
Ignition Delay Times ◽  
Test Region ◽  
Fuel Characterization

Synthetic fuels such as Fischer-Tropsch (FT) fuels are of interest as a replacement for aviation, diesel, and other petroleum-based fuels, and the present paper outlines a joint program to study the combustion behavior of FT synthetic fuels. To this end, shock-tube spray and high-recirculation combustion rig experiments are being utilized to study the ignition delay times, formation of soot, and emissions of FT jet fuels. Undiluted shock tube spray experiments were conducted using a recently developed heterogeneous technique wherein the fuel is sprayed directly into the test region of a shock tube. The high recirculation combustion rig is a complete gas turbine system where Syntroleum FT jet fuel was combusted, and soot formation and emission characteristics were observed. Reduction of soot volume fraction and unchanged emissions were observed, in agreement with previous investigations. The fundamental shock tube results were found to be consistent with the observations made in the experimental engine.

scholarly journals A Numerical Investigation on Soot Formation From Laminar Diffusion Flames of Ethylene/Methane Mixture

2008 ◽  
Author(s):  
Hongsheng Guo ◽  
Stephanie Trottier ◽  
Matthew R. Johnson ◽  
Gregory J. Smallwood
Keyword(s):  
Volume Fraction ◽  
Diffusion Flames ◽  
Soot Formation ◽  
Soot Volume Fraction ◽  
Fuel Mixture ◽  
Methyl Radical ◽  
Laminar Diffusion Flames ◽  
Laminar Diffusion ◽  
Methane Mixture ◽  
Phase Chemistry

The sooting propensity of laminar diffusion flames employing ethylene/methane mixture fuel is investigated by numerical simulation. Detailed gas phase chemistry and moments method are used to describe the chemical reaction process and soot particle dynamics, respectively. The numerical model captures the primary features experimentally observed previously. At constant temperatures of air and fuel mixture, both maximum soot volume fraction and soot yield monotonically decrease with increasing the fraction of carbon from methane in the fuel mixture. However, when the temperatures of air and fuel mixture are preheated so that the adiabatic temperatures of all flames are same, the variation of the maximum soot yield becomes higher than what would be expected from a linear combination of the flames of pure ethylene and pure methane, showing a synergistic phenomenon in soot formation. Further analysis of the details of the numerical results suggests that the synergistic phenomenon is caused by the combined effects of the variations in the concentrations of acetylene (C2H2) and methyl radical (CH3). When the fraction of carbon from methane in fuel mixture increases, the concentration of C2H2 monotonically decreases, whereas that of methyl radical increases, resulting in a synergistic phenomenon in the variation of propargyl (C3H3) radical concentration due to the reactions C2H2 + CH3 = PC3H4 + H and PC3H4 + H = C3H3 + H2. This synergistic phenomenon causes a qualitatively similar variation trend in the concentration of pyrene (A4) owing to the reaction paths C3H3 → A1 (benzene) → A2 (naphthalene) → A3 (phenanthrene) → A4. Consequently, the synergistic effect occurs for soot inception and PAH condensation rates, leading to the synergistic phenomenon in soot yield. The similar synergistic phenomenon is not observed in the variation of peak soot volume fraction, since the maximum surface growth rate monotonically decreases, as the fraction of carbon from methane in fuel mixture increases.

Sign in / Sign up

Export Citation Format

Share Document