Design and fabrication of miniaturized tri-band frequency selective surface with polarization-independent and angularly stable response

Frequenz ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Sayi Soundariya Sampath ◽  
Ramprabhu Sivasamy
Keyword(s):  
Resonance Frequency ◽  
Figure Of Merit ◽  
Close Agreement ◽  
Single Layer ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Band Frequency ◽  
Tm Mode ◽  
Frequency Selective ◽  
Polarization Independent

Abstract A single-layer miniaturized tri-band frequency selective surface (FSS) for bandstop filtering applications has been proposed in this work. The metallic layer with four-branched meandered pattern connected in the center is engraved on a dielectric FR-4 substrate. The three stopbands operating at 2.6, 5.6, and 7.1 GHz provides −10 dB bandwidth of 437, 447, and 552 MHz respectively. The size of the unit cell is 0.067 λ∘ × 0.067 λ∘, where λ∘ is the wavelength of the first resonance frequency. As a figure of merit, the symmetric FSS structure provides the advantage of polarization independence. The proposed compact FSS structure exhibits a stable angular response up to 60° in TE and TM mode. Moreover, measurements obtained from the fabricated prototype are compared with the simulated results and are found to be in close agreement.

Polarization-independent single-layer ultra-wideband frequency-selective surface

2015 ◽  
Vol 9 (1) ◽  
pp. 93-97 ◽  
Author(s):  
Ramprabhu Sivasamy ◽  
Balaji Moorthy ◽  
Malathi Kanagasabai ◽  
Jithila V. George ◽  
Livya Lawrance ◽  
...  
Keyword(s):  
Free Space ◽  
Single Layer ◽  
Normal Incidence ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Ultra Wideband ◽  
Attenuation Level ◽  
Wide Range ◽  
Frequency Selective ◽  
Polarization Independent

An ultra-wideband (UWB) frequency-selective surface (FSS) exhibiting band rejection characteristic is presented in this paper. The proposed unit cell has the size of 14 × 14 mm2 which is approximately 0.18 × 0.18 λo, where λo corresponds to free space wavelength at the lower cut-off frequency. The proposed UWB FSS consists of a single-layer substrate and provides 20 dB attenuation level for a wide bandwidth of 7.53 GHz at the normal incidence. The proposed FSS is polarization independent and also provides angular-independent operation for the EM wave incidences of 15°, 30° and 45° with 11.5 dB attenuation over a wide range from 4 to 14 GHz.

scholarly journals Miniaturized Angularly Stable Dual Band Frequency Selective Surface for K and Ka Band

2020 ◽  
pp. 100-103
Author(s):  
Singaram M ◽  
Krishna Kumar E ◽  
Chandraprasad V ◽  
Finney Daniel Shadrach ◽  
Gowthaman Manoharan
Keyword(s):  
Satellite Communication ◽  
Cell Structure ◽  
Single Layer ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Dual Band ◽  
Angle Of Incidence ◽  
Band Frequency ◽  
Ka Band ◽  
Frequency Selective

A single layer novel compact frequency selective surface which is used in reflector antenna is designed and simulated. The proposed unit cell reflects electromagnetic waves in K and Ka band with maximum reflection occurring at 22.62 GHz and 35.44 GHz respectively. The designed FSS find its application in satellite communication. A crossed dipole structure in center and two-legged structure in corners with square loop in each quadrant makes the FSS unit cell structure. The FSS is designed with oblique incidence for transverse electric and transverse magnetic polarization with return loss 0.3 dB in 22.62 GHz and less than 0.5 dB in 35.44 GHz. The proposed work shows frequency independence against oblique angle of incidence. The simulated result from CST microwave studio is compared with other similar works.

Angle and polarization-independent miniaturized UWB FSS design

2021 ◽  
pp. 1-9
Author(s):  
Yanning Yuan ◽  
Yuchen Zhao ◽  
Xiaoli Xi
Keyword(s):  
Design Method ◽  
Incident Angle ◽  
Stop Band ◽  
Single Layer ◽  
Wireless Systems ◽  
Frequency Selective Surface ◽  
Ultra Wideband ◽  
Band Frequency ◽  
Gain Enhancement ◽  
Polarization Independent

Abstract A single-layer ultra-wideband (UWB) stop-band frequency selective surface (FSS) has several advantages in wireless systems, including a simple design, low debugging complexity, and an appropriate thickness. This study proposes a miniaturized UWB stop-band FSS design. The proposed FSS structure consists of a square-loop and metalized vias that are arranged on a single layer substrate; it has an excellent angle and polarization-independent characteristics. At an incident angle of 60°, the polarization response frequencies of the transverse electric and magnetic modes only shifted by 0.003 f0 and 0.007 f0, respectively. The equivalent circuit models of the square-loop and metallized vias structure are analysed and the accuracy of the calculation is evaluated by comparing the electromagnetic simulation. The 20 × 20 array constitutes an FSS reflector with a unit size of 4.2 mm × 4.2 mm (less than one-twentieth of the wavelength of 3 GHz), which realizes an UWB quasi-constant gain enhancement (in-band flatness is <0.5 dB). Finally, the simulation results were verified through sample processing and measurement; consistent results were obtained. The FSS miniaturization design method proposed in this study could be applied to the design of passband FSS (complementary structure), antennas and filters, among other applications.

Polarization independent bandstop frequency selective surface for X-band application

Circuit World ◽  
2019 ◽  
Vol 46 (1) ◽  
pp. 25-31
Author(s):  
Kanchana D. ◽  
Radha Sankararajan ◽  
Sreeja B.S. ◽  
Manikandan E.
Keyword(s):  
Frequency Selective Surface ◽  
Transverse Magnetic ◽  
Unit Cell Dimension ◽  
Unit Cell ◽  
Content Type ◽  
Low Profile ◽  
X Band ◽  
Measurement Results ◽  
Frequency Selective ◽  
Polarization Independent

Purpose A novel low profile frequency selective surface (FSS) with a band-stop response at 10 GHz is demonstrated. The purpose of this designed FSS structure is to reject the X-band (8-12 GHz) for the application of shielding. The proposed FSS structure having the unit cell dimension of 8 × 8 mm2, the miniaturization of the FSS unit cell in terms of λ0 is 0.266 λ0 × 0.266 λ0, where λ0 is free space wavelength. The designed FSS provides 4 GHz bandwidth with insertion loss of 15 dB. The transverse electric (TE) and transverse magnetic (TM) modes of the proposed design are same because of polarization independent characteristics and hold the angularly stable frequency response for both TE and TM mode polarization. Both the simulation and measurement results are in good agreement to each other. Design/methodology/approach The proposed FSS design contains square-shaped PEC material, which is placed on the substrate and the shape of the circle and rectangle is etched over the PEC material. The PEC material of the patch dimension is 0.0175 mm. The substrate used for the proposed design is FR4 lossy with the thickness of 0.8 mm and permittivity εr = 4.3 having a loss tangent of 0.02. Findings To find a new design and miniaturized FSS structure is discussed. Originality/value 100%

A novel design of ultra-wide stop-band single-layer frequency selective surface using square-loop and cross

2020 ◽  
pp. 1-10
Author(s):  
Amit Birwal ◽  
Sanjeev Singh ◽  
Binod Kumar Kanaujia
Keyword(s):  
Stop Band ◽  
Single Layer ◽  
Frequency Selective Surface ◽  
Transverse Magnetic ◽  
Unit Cell ◽  
Gain Enhancement ◽  
Single Side ◽  
Frequency Selective ◽  
Novel Design ◽  
Excellent Stability

Abstract In this paper, a novel design of ultra-wide stop-band single-side single-layer frequency selective surface (FSS) is presented. The unit cell of the proposed FSS is designed using the combination of conventional square loop and cross (CSLC). To enhance the bandwidth of this structure, an additional cross is inserted in all the four quadrants of CSLC. The stop-band transmission bandwidth assuming −10 dB threshold is found to be 128.94% (2.16–10 GHz) which is 34.33% more as compared to the bandwidth of CSLC. The unit cell with a dimension of 16 × 16 mm2 is printed on one side of an FR4 substrate. The design is fabricated and the measured results are found to be in good agreement with the simulated results. The design provides excellent stability for both transverse magnetic and transverse electric polarizations. The design is very flexible, where any resonant frequency can be achieved by changing the length of unit cell. The design is useful in many applications such as antenna gain enhancement, electromagnetic wave shielding for Wi-Fi/5G systems, and other Internet of Things-based applications.

Single layer miniaturized ultra-thin FSS with five closely spaced bands

2019 ◽  
Vol 11 (08) ◽  
pp. 797-805 ◽  
Author(s):  
Anupam Dey ◽  
Rajarshi Sanyal
Keyword(s):  
Resonant Frequency ◽  
Cell Size ◽  
Cell Structure ◽  
Single Layer ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Angular Stability ◽  
Band Frequency ◽  
Unit Cell Size ◽  
Unit Cell Structure

AbstractThis Paper reveals a novel single layer five band frequency selective surface (FSS). Novelties of the proposed FSS lie in its five closely spaced stop bands at 2.4, 3.38, 4.82, 6.32, and 7.75 GHz as well as the reduced single layer structural thickness (0.0016 λ0) and the miniaturized unit cell size (0.0656 λ0) at lower resonant frequency as compared to the existing multiband FSS. The unit cell structure consists of six octagonal concentric interconnected loops. Adjacent loop interconnection technique reduces the cell size by more than 44%. Furthermore, arrow-shaped rings are also introduced on each corner of the outermost octagonal loop, and using this technique approximate 23% cell miniaturization can be achieved. In addition, the proposed FSS exhibits excellent angular stability.

Polarization Independent Triple-Band Frequency Selective Surface Based on Matryoshka Geometry

2019 ◽  
Author(s):  
Alfredo Gomes Neto ◽  
Jefferson Costa e Silva ◽  
Ianes Barbosa Grecia Coutinho ◽  
Marina de Oliveira Alencar ◽  
Iasmin de Franca Albuquerque ◽  
...  
Keyword(s):  
Frequency Selective Surface ◽  
Band Frequency ◽  
Frequency Selective ◽  
Polarization Independent ◽  
Triple Band
Sign in / Sign up

Export Citation Format

Share Document