Design of X-band frequency selective surface (FSS) with band pass characteristics based on miniaturized unit cell

2016 ◽  
Author(s):  
Tariq Rahim ◽  
Fawad Azam Khan ◽  
Xu Jiadong
Keyword(s):  
Frequency Selective Surface ◽  
Unit Cell ◽  
Band Frequency ◽  
X Band ◽  
Band Pass ◽  
Frequency Selective

scholarly journals X-band Band-pass Frequency Selective Surface for Radome Applications

2015 ◽  
Vol 16 (2) ◽  
pp. 281
Author(s):  
Tariq Rahim ◽  
Jiodong Xu
Keyword(s):  
Frequency Selective Surface ◽  
Unit Cell ◽  
Dielectric Substrates ◽  
Low Profile ◽  
X Band ◽  
Analysis And Synthesis ◽  
Unit Cells ◽  
Band Pass ◽  
Frequency Selective ◽  
Unit Cell Dimensions

A low profile multi layer miniaturized unit cell frequency selective surface (FSS) with second-order band-pass response is design. The metallic layers in the form of capacitive patches and inductive grids are separated by dielectric substrates. The non-resonant sub-wavelength unit cells with unit cell dimensions and periodicities on the order of 0.15λ. The overall thickness of approximately 0.03λ is designed which is useful at lower frequencies with long wavelengths. The FSS exhibit a stable frequency response to different angles of incidence and polarizations. The analysis and synthesis of the FSS is done using equivalent circuit method and simulated using CST microwave studio at X-band.

scholarly journals Elliptical BandPassThree Dimensional Frequency Selective Surface with Multiple Transmission Zeros

2018 ◽  
Vol 12 (3) ◽  
pp. 1020
Author(s):  
Bimal Raj Dutta ◽  
Binod Kumar Kanaujia ◽  
Chhaya Dalela
Keyword(s):  
Plane Wave ◽  
Incident Angle ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Long Distance ◽  
Band Frequency ◽  
Microstrip Lines ◽  
Transmission Zeros ◽  
Band Pass ◽  
Frequency Selective

An elliptic band pass response three-dimensional Frequency Selective Surface (3D FSS) is designed from a single unit cell of 2D array of two shielded microstrip lines. The designed FSS provides pseudo-elliptic band-pass frequency response (5.4 – 9.6) GHz with its application in long-distance radio telecommunications and space communications etc. The four transmission zeros at 5.4GHz, 9.6GHz, 12.4GHz and 15GHz provides wide out-of-band frequency rejection. The 3D FSS is independent of the variations in the incident angle of the plane wave up to 60 degree. Each unit cell is a combination of two shielded microstrip lines with one having an air gap and the other one having in between rectangular metallic plate. When a TE polarized plane wave incidents perpendicular to the perfect electric conductor (PEC) boundary walls shielded microstrip lines, it results in two quasi-TEM modes namely air and substrate mode. The 3D FSS consists of multiple resonators with a multimode cavity having number of propagating modes. These resonating modes in phase provide transmission poles and when out of phase give transmission zeros. The 3D FSS structure is simulated using Ansys HFSS software with improved performance over 2DFSS, for many practical applications such as antenna sub-reflector, radomes and spatial filters.

Polarization independent bandstop frequency selective surface for X-band application

Circuit World ◽  
2019 ◽  
Vol 46 (1) ◽  
pp. 25-31
Author(s):  
Kanchana D. ◽  
Radha Sankararajan ◽  
Sreeja B.S. ◽  
Manikandan E.
Keyword(s):  
Frequency Selective Surface ◽  
Transverse Magnetic ◽  
Unit Cell Dimension ◽  
Unit Cell ◽  
Content Type ◽  
Low Profile ◽  
X Band ◽  
Measurement Results ◽  
Frequency Selective ◽  
Polarization Independent

Purpose A novel low profile frequency selective surface (FSS) with a band-stop response at 10 GHz is demonstrated. The purpose of this designed FSS structure is to reject the X-band (8-12 GHz) for the application of shielding. The proposed FSS structure having the unit cell dimension of 8 × 8 mm2, the miniaturization of the FSS unit cell in terms of λ0 is 0.266 λ0 × 0.266 λ0, where λ0 is free space wavelength. The designed FSS provides 4 GHz bandwidth with insertion loss of 15 dB. The transverse electric (TE) and transverse magnetic (TM) modes of the proposed design are same because of polarization independent characteristics and hold the angularly stable frequency response for both TE and TM mode polarization. Both the simulation and measurement results are in good agreement to each other. Design/methodology/approach The proposed FSS design contains square-shaped PEC material, which is placed on the substrate and the shape of the circle and rectangle is etched over the PEC material. The PEC material of the patch dimension is 0.0175 mm. The substrate used for the proposed design is FR4 lossy with the thickness of 0.8 mm and permittivity εr = 4.3 having a loss tangent of 0.02. Findings To find a new design and miniaturized FSS structure is discussed. Originality/value 100%

Design and fabrication of miniaturized tri-band frequency selective surface with polarization-independent and angularly stable response

Frequenz ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Sayi Soundariya Sampath ◽  
Ramprabhu Sivasamy
Keyword(s):  
Resonance Frequency ◽  
Figure Of Merit ◽  
Close Agreement ◽  
Single Layer ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Band Frequency ◽  
Tm Mode ◽  
Frequency Selective ◽  
Polarization Independent

Abstract A single-layer miniaturized tri-band frequency selective surface (FSS) for bandstop filtering applications has been proposed in this work. The metallic layer with four-branched meandered pattern connected in the center is engraved on a dielectric FR-4 substrate. The three stopbands operating at 2.6, 5.6, and 7.1 GHz provides −10 dB bandwidth of 437, 447, and 552 MHz respectively. The size of the unit cell is 0.067 λ∘ × 0.067 λ∘, where λ∘ is the wavelength of the first resonance frequency. As a figure of merit, the symmetric FSS structure provides the advantage of polarization independence. The proposed compact FSS structure exhibits a stable angular response up to 60° in TE and TM mode. Moreover, measurements obtained from the fabricated prototype are compared with the simulated results and are found to be in close agreement.

scholarly journals A Tri-band Second-order Frequency Selective Surface Designing and Analysis

2021 ◽  
Vol 275 ◽  
pp. 03084
Author(s):  
Gao Shan ◽  
ChunYan Gao ◽  
HongBin Pu ◽  
ChunLan Chen
Keyword(s):  
Frequency Selective Surface ◽  
Second Order ◽  
Dual Band ◽  
Microwave Filter ◽  
Band Frequency ◽  
Dielectric Layers ◽  
Band Pass ◽  
Frequency Selective ◽  
Band Separation ◽  
Excellent Stability

In this paper, inspired from the technique of patch–aperture–patch, a novel tri-band frequency selective surface with second-order band-pass response in each operation band is presented. The design is implemented by cascading a two-dimensional periodic array of three square loops and an array of wire grids. The proposed structure composed of three metal and two dielectric layers acts as a spatial dual band microwave filter with large band separation. The predicted FSS has the merits of broadband response, excellent stability for different incident angles, and sharp roll-off at X-, Ku- and K-band, respectively. The simulation and measurement are carried out and discussed. The measured results agree well with the simulated ones.

A miniaturized flexible frequency selective surface for dual band response

2020 ◽  
pp. 1-7
Author(s):  
Durai Kanchana ◽  
Sankararajan Radha ◽  
Balakrishnapillai Suseela Sreeja ◽  
Esakkimuthu Manikandan
Keyword(s):  
Frequency Response ◽  
Transverse Electric ◽  
Frequency Selective Surface ◽  
Transverse Magnetic ◽  
Dual Band ◽  
Band Frequency ◽  
X Band ◽  
Stable Frequency ◽  
Frequency Selective ◽  
Ku Band

Abstract In this paper, a novel miniaturized and flexible dual band frequency selective surface (FSS) is presented. This FSS provides effective shielding in X-band and Ku- band, with a frequency response of 9.4 and 16.7 GHz, respectively. The proposed FSS provides 924 MHz bandwidth at X-band and 1.34 GHz bandwidth at Ku-band with an insertion loss of 20 dB. Moreover, the proposed design is polarization-independent and it provides stable frequency response at various angles of incidences for both transverse electric and transverse magnetic modes. More significantly, the proposed FSS analyzed the bandstop response of the selective frequency and also is suitable for conformal applications. A prototype of the proposed FSS is fabricated. The measured results and simulated results are good in agreement.

scholarly journals A Miniaturized Frequency Selective Surface Based on Square Loop Aperture Element

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Wenxing Li ◽  
Chunming Wang ◽  
Yong Zhang ◽  
Yingsong Li
Keyword(s):  
Theoretical Analysis ◽  
Cell Structure ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Angle Stability ◽  
Band Pass ◽  
Simulation Results ◽  
Frequency Selective ◽  
Unit Cell Structure ◽  
Periodic Unit Cell

We propose a miniaturized band-pass frequency selective surface (FSS) with periodic unit cell structure. The proposed FSS is realized by symmetrically bending the edges of the square loop aperture element, by which our proposed FSS increases the resonant length, and, hence, reduces its size. In this FSS, each unit cell has a dimension of 0.0538λ × 0.0538λ, whereλrepresents the wavelength of the corresponding resonant frequency. Both the theoretical analysis and simulation results demonstrate that our proposed FSS, having high polarization stability and angle stability, can achieve smaller size in comparison with the previously proposed structures.

scholarly journals Miniaturized Angularly Stable Dual Band Frequency Selective Surface for K and Ka Band

2020 ◽  
pp. 100-103
Author(s):  
Singaram M ◽  
Krishna Kumar E ◽  
Chandraprasad V ◽  
Finney Daniel Shadrach ◽  
Gowthaman Manoharan
Keyword(s):  
Satellite Communication ◽  
Cell Structure ◽  
Single Layer ◽  
Frequency Selective Surface ◽  
Unit Cell ◽  
Dual Band ◽  
Angle Of Incidence ◽  
Band Frequency ◽  
Ka Band ◽  
Frequency Selective

A single layer novel compact frequency selective surface which is used in reflector antenna is designed and simulated. The proposed unit cell reflects electromagnetic waves in K and Ka band with maximum reflection occurring at 22.62 GHz and 35.44 GHz respectively. The designed FSS find its application in satellite communication. A crossed dipole structure in center and two-legged structure in corners with square loop in each quadrant makes the FSS unit cell structure. The FSS is designed with oblique incidence for transverse electric and transverse magnetic polarization with return loss 0.3 dB in 22.62 GHz and less than 0.5 dB in 35.44 GHz. The proposed work shows frequency independence against oblique angle of incidence. The simulated result from CST microwave studio is compared with other similar works.

Sign in / Sign up

Export Citation Format

Share Document