Changes in the wood-water interactions of mahogany wood due to heat treatment

Holzforschung ◽  
2020 ◽  
Vol 74 (9) ◽  
pp. 853-863
Author(s):  
Fan Zhou ◽  
Zongying Fu ◽  
Xin Gao ◽  
Yongdong Zhou
Keyword(s):  
Heat Treatment ◽  
Environmental Temperature ◽  
Treated Wood ◽  
Fiber Saturation Point ◽  
Surface Wettability ◽  
Resonance Spectroscopy ◽  
Saturation Point ◽  
Fiber Saturation ◽  
Heat Treated ◽  
Higher Temperature

AbstractMahogany wood (Swietenia macrophylla King) was thermally modified by heating at various temperatures. The wood-water-related parameters of the heat-treated wood, including fiber saturation point, equilibrium moisture content, moisture excluding efficiency, hygroscopic hysteresis, swelling, anti-swelling efficiency, water adsorption, and surface wettability were determined to clarify the mechanism of heat treatment to reduce wood hygroscopicity. The wood treated at a higher temperature demonstrated a more significant decrease in hygroscopicity. The reduction in hygroscopicity of the heat-treated wood was partially diminished as the moisture excluding efficiency decreased in the absorption and desorption processes caused by the changes in environmental temperature and relative humidity. The fiber saturation point (determined by nuclear magnetic resonance spectroscopy), surface free energy, and the surface wettability of wood were reduced by heat treatment, resulting in the decreased hygroscopicity of the heat-treated wood. Mahogany wood became more insensitive to the influence of moisture due to the heat treatment, and this effect was more distinct for wood treated at a high temperature.

Effect of copper incorporation on phase transformation behavior of electroless nickel–phosphorous coating and its effect on the tribological behavior

2020 ◽  
pp. 146442072098160
Author(s):  
Abhijit Biswas ◽  
Suman Kalyan Das ◽  
Prasanta Sahoo
Keyword(s):  
Heat Treatment ◽  
Phase Transformation ◽  
Tribological Behavior ◽  
Electroless Nickel ◽  
Two Phase ◽  
Microstructural Changes ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Higher Temperature ◽  
Effect Of Copper

The microstructural changes of electroless Ni–P–Cu coating at various heat-treatment conditions are investigated to understand its implications on the tribological behavior of the coating. Coatings are heat-treated at temperatures ranging between 200°C and 800 °C and for 1–4 h duration. Ni–P–Cu coatings exhibit two-phase transformations in the temperature range of 350–450 °C and the resulting microstructural changes are found to significantly affect their thermal stability and tribological attributes. Hardness of the coating doubles when heat-treated at 452 °C, due to the formation of harder Ni3P phase and crystalline NiCu. Better friction and wear performance are also noted upon heat treatment of the coating at the phase transformation regime, particularly at 400 °C. Wear mechanism is characterized by a mixed adhesive cum abrasive wear phenomena. Heat treatment at higher temperature (600 °C and above) and longer duration (4 h) results in grain coarsening phenomenon, which negatively influences the hardness and tribological characteristics of the coating. Besides, diffusion of iron from the ferrous substrate as well as greater oxide formation are noticed when the coating is heat-treated at higher temperatures and for longer durations (4 h).

Comparison of the color and weight change in Paulownia tomentosa and Pinus koraiensis wood heat-treated in hot oil and hot air

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5574-5585
Author(s):  
Intan Fajar Suri ◽  
Jong Ho Kim ◽  
Byantara Darsan Purusatama ◽  
Go Un Yang ◽  
Denni Prasetia ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Color Change ◽  
Treated Wood ◽  
Pinus Koraiensis ◽  
Weight Changes ◽  
Paulownia Tomentosa ◽  
Wood Color ◽  
Color Changes ◽  
Hot Air ◽  
Heat Treated

Color changes were tested and compared for heat-treated Paulownia tomentosa and Pinus koraiensis wood treated with hot oil or hot air for further utilization of these species. Hot oil and hot air treatments were conducted at 180, 200, and 220 °C for 1, 2, and 3 h. Heat-treated wood color changes were determined using the CIE-Lab color system. Weight changes of the wood before and after heat treatment were also determined. The weight of the oil heat-treated wood increased considerably but it decreased in air heat-treated wood. The oil heat-treated samples showed a greater decrease in lightness (L*) than air heat-treated samples. A significant change in L* was observed in Paulownia tomentosa. The red/green chromaticity (a*) of both wood samples increased at 180 and 200 °C and slightly decreased at 220 °C. The yellow/blue chromaticity (b*) in both wood samples increased at 180 °C, but it rapidly decreased with increasing treatment durations at 200 and 220 °C. The overall color change (ΔE*) in both heat treatments increased with increasing temperature, being higher in Paulownia tomentosa than in Pinus koraiensis. In conclusion, oil heat treatment reduced treatment duration and was a more effective method than air heat treatment in improving wood color.

scholarly journals COLOR CHANGE — MASS LOSS CORRELATION FOR HEAT-TREATED WOOD

2014 ◽  
Vol 2 ◽  
pp. 345-352 ◽  
Author(s):  
Cristina Marinela Olarescu ◽  
Mihaela Campean
Keyword(s):  
Heat Treatment ◽  
Mass Loss ◽  
Color Change ◽  
Treated Wood ◽  
Untreated Wood ◽  
Cost Effective ◽  
Assessment Procedure ◽  
Mathematical Correlation ◽  
Heat Treated ◽  
Two Parameters

Heat treatment is renowned as the most environmentally friendly process of dimensional stabilization that can be applied to wood, in order to make it suitable for outdoor uses. It also darkens wood color and improves wood durability. The intensity of heat treatment can be appreciated by means of two parameters: the color change occured in wood due to the high temperature, and the mass loss, which is a measure of the degree of thermal degradation. In order to find a mathematical correlation between these two parameters, an experimental study was conducted with four European wood species, which were heat-treated at 180°C and 200ºC, for 1-3 hours, under atmosheric pressure.The paper presents the results concerning the color changes and mass losses recorded for the heat-treated wood samples compared to untreated wood.  For all four species, the dependency between the color change and the mass loss was found to be best described by a logarithmic regression equation with R2 of 0.93 to 0.99 for the soft species (spruce, pine and lime), and R2 of 0.77 for beech. The results of this study envisage to simplify the assessment procedure of the heat treatment efficiency, by only measuring the color – a feature that is both convenient and cost-effective. 

scholarly journals Determination of fiber saturation point of rattan (Calamus simplicifolius) using the LF-NMR and two conventional methods

2020 ◽  
Vol 54 (3) ◽  
pp. 667-682
Author(s):  
Limei Yang ◽  
Genlin Tian ◽  
Shumin Yang ◽  
Lili Shang ◽  
Xing’e Liu ◽  
...  
Keyword(s):  
Fiber Saturation Point ◽  
Saturation Point ◽  
Fiber Saturation ◽  
Conventional Methods ◽  
Calamus Simplicifolius ◽  
Lf Nmr

scholarly journals Effects of aluminum sulfate soaking pretreatment on dimensional stability and thermostability of heat-treated wood

2020 ◽  
Author(s):  
Lijie Qu ◽  
Zhenyu Wang ◽  
Jing Qian ◽  
Zhengbin He ◽  
Songlin Yi
Keyword(s):  
Heat Treatment ◽  
Thermal Stability ◽  
Thermal Degradation ◽  
Structural Changes ◽  
Aluminum Sulfate ◽  
Treated Wood ◽  
Treatment Temperature ◽  
Chinese Fir ◽  
Heat Treated ◽  
Thermal Stability Of

Abstract Acidic aluminum sulfate hydrolysis solutions can be used to catalyze the thermal degradation of wood in a mild temperature environment, and thus reduce the temperature required for heat treatment process. To improve the dimensional and thermal stability of Chinese fir during heat treatment at 120 °C, 140 °C and 160 °C, this study investigated the effects of soaking pretreatment with 5%, 10% and 15% aluminum sulfate on the chemical and structural changes of the heat-treated Chinese fir. The results indicated that the samples treated at 15% aluminum sulfate concentration and 160 °C heat treatment achieved the best dimensional and thermal stability. Chemical analyses by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) indicated that the catalysis of aluminum sulfate resulted in degradation of hemicelluloses during the heat treatment, and an increase in the soaking concentration and heat treatment temperature also affected the thermal degradation of celluloses. The scanning electron microscope (SEM) and mass changes test results proved that the hydrolyzed aluminum flocs mainly adhered to the inner wall of the wood tracheid as spherical precipitates, and when the soaking concentration reached 10% and 15%, a uniform soaking effect could be achieved. The thermogravimetric (TG) analysis revealed the soaking pretreatment effectively improved the thermal stability of the heat-treated wood by physically wrapping and promoting the formation of a carbon layer on the wood surface during heat treatment. Thus, aluminum sulfate soaking pretreatment exerted a great effect on the dimensional and thermal stability of wood, allowing heat treatment to be performed at a lower temperature.

scholarly journals Calorific Power Improvement of Wood by Heat Treatment and Its Relation to Chemical Composition

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5322
Author(s):  
Idalina Domingos ◽  
Umit Ayata ◽  
José Ferreira ◽  
Luisa Cruz-Lopes ◽  
Ali Sen ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Chemical Composition ◽  
Lignin Content ◽  
Treated Wood ◽  
Untreated Wood ◽  
High Heating Value ◽  
Heat Treated ◽  
Positive Linear Correlation ◽  
Total Extractives ◽  
Calorific Power

Chemical composition influences the calorific power of wood, mainly due to the calorific power of structural compounds and extractives. Heat treatment changes the chemical composition of treated wood. This work studies the relationship between chemical composition and calorific power improvement by heat treatment. Samples were heat-treated by the ThermoWood process ® for 1 h and 2 h. High heating value (HHV) and chemical composition; lignin, cellulose, hemicelluloses and extractives in dichloromethane, ethanol, and water were determined. The HHV of untreated wood ranged between 18.54–19.92 MJ/kg and increased with heat treatment for all the tested species. A positive linear correlation was found between HHV and Klason lignin (R2 = 0.60). A negative trend was observed for holocellulose, cellulose, and hemicelluloses content against HHV, but with low determination coefficients for linear regression. The best adjust for polysaccharides was found for hemicelluloses content. A positive correlation could be found for dichloromethane extractives (R2 = 0.04). The same was obtained in relation to ethanol extractives with R2 = 0.20. For water and total extractives, no clear positive or negative trends could be achieved. The results showed that the HHV of wood increased with heat treatment and that this increase was mainly due to the increase in lignin content.

scholarly journals Heat-Treated Wood as a Substrate for Coatings, Weathering of Heat-Treated Wood, and Coating Performance on Heat-Treated Wood

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Vlatka Jirouš-Rajković ◽  
Josip Miklečić
Keyword(s):  
Heat Treatment ◽  
Wood Species ◽  
Treated Wood ◽  
Wood Properties ◽  
Treatment Method ◽  
Coating Performance ◽  
Treatment Processes ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Trade Names

Heat treatment is a method of wood modification with increasing market acceptance in Europe. The major patented European commercial heat treatment processes have trade names ThermoWood, Platowood, Retiwood, Le Bois Perdure, and Oil-Heat-Treated Wood (OHT). To what extent modification of wood affects the resistance of wood to weathering is also an important aspect for wood applications, especially where appearance is important. Unfortunately, heat-treated wood has poor resistance to weathering, and surface treatment with coatings is required for both protection and aesthetic reasons. As a substrate for coating, heat-treated wood has altered characteristics such as lower hygroscopicity and liquid water uptake and changed acidity, wettability, surface free energy, and anatomical microstructure. Various wood species, heat treatment method, treatment intensity, and treatment conditions exhibited a different extent of changes in wood properties. These altered properties could affect coating performance on heat-treated wood. The reported changes in acidity and in surface energy due to heat treatments are inconsistent with one another depending on wood species and temperature of the treatments. This paper gives an overview of the research results with regards to properties of heat-treated wood that can affect coating performance and weathering of uncoated and coated heat-treated wood.

Moisture in softwoods: fiber saturation point, hydroxyl site content, and the amount of micropores as determined from NMR relaxation time distributions

Holzforschung ◽  
2013 ◽  
Vol 67 (3) ◽  
pp. 291-300 ◽  
Author(s):  
Ville-Veikko Telkki ◽  
Miikka Yliniemi ◽  
Jukka Jokisaari
Keyword(s):  
Melting Point ◽  
Relaxation Times ◽  
Bound Water ◽  
Nmr Relaxation ◽  
Free Water ◽  
Bulk Water ◽  
Fiber Saturation Point ◽  
Saturation Point ◽  
Fiber Saturation ◽  
Nmr Relaxation Times

Abstract Distributions of nuclear magnetic resonance (NMR) relaxation times provide detailed information about the moisture absorbed in wood. In this work, T2*, T2, and T1 distributions were recorded from fresh sapwood and heartwood samples of pine (Pinus sylvestris) and spruce (Picea abies) at various temperatures. Below the melting point of bulk water, free water is frozen and its signal disappears from the distributions. Then, the low-temperature distributions of the unfrozen bound water contain more information about its components, because the large free water peaks hiding some smaller bound water peaks are absent and the exchange between free and bound water is prevented. Comparison of the total moisture signal integrals above and below the bulk melting point enables the determination of fiber saturation point (FSP), which, in this context, denotes the total water capacity of cell wall. T2*, T2, and T1 distributions offer different kinds of information about moisture components. All the peaks in the distributions were assigned, and it was demonstrated that the accessible hydroxyl site content and the amount of micropores can be estimated based on the peak integrals.

Sign in / Sign up

Export Citation Format

Share Document