scholarly journals Freeze-Thaw Resistance of Cement Screed with Various Supplementary Cementitious Materials

2019 ◽  
Vol 58 (1) ◽  
pp. 66-74 ◽  
Author(s):  
Pavel Reiterman ◽  
Ondřej Holčapek ◽  
Ondřej Zobal ◽  
Martin Keppert
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Frost Resistance ◽  
Blast Furnace Slag ◽  
Ceramic Powder ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Freeze Thaw ◽  
Mineral Additives ◽  
Furnace Slag

Abstract This paper describes a study of the effect of partial replacement of ordinary Portland cement (OPC) by various mineral additives in the screed mixtures. Ceramic powder, blast furnace slag and fly ash were gradually employed in increments of 12.5 wt.% up to 50 wt.% to replace OPC. The mixtures were designed to a constant consistency. The influence of mineral additives was evaluated in terms of the air content in the fresh mixtures, the compressive strength, the flexural strength and the freeze-thaw resistance and using non-destructive measurements after 28 and 90 days. The accompanied paste sampleswere analysed using thermogravimetry to monitor the hydration process by means of total bound water content. The decrease in the mechanical properties and the frost resistance of the mixtures with the mineral additives were recorded, because of the necessity for a larger addition of water. According to the valid standards for concrete screed related to the frost resistance, it could be concluded that maximal suitable cement replacement contents are 12.5, 37.5 and 50 wt.% for ceramic powder, fly ash and blast furnace slag, respectively. The freeze-thaw resistance of the studied materials was found to be strongly related to the content of CSH and CAH hydrates.

scholarly journals Effect of Mineral Admixtures on the Sulfate Resistance of High-Strength Piles Mortar

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3500
Author(s):  
Yanyan Hu ◽  
Linlin Ma ◽  
Tingshu He
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
High Strength ◽  
Mineral Admixtures ◽  
Quartz Powder ◽  
Sulfate Resistance ◽  
Powder Samples ◽  
Mineral Additives ◽  
Furnace Slag

Pre-stressed high-strength concrete piles (PHCP) are widely used in the building industry in China. The main aim of our research was to investigate the utilization of quartz powder, fly ash, and blast furnace slag as mineral additives to prepare PHCP mortar. The samples were prepared using steam and autoclaving steaming. The influence of minerals on the sulfate resistance of mortar was analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP) tests. The results showed that when compared to single doped quartz powder samples, samples prepared using fly ash or blast furnace slag improved the sulfate resistance of the PHCP mortar. Furthermore, the resistance to sulfate attack of samples with dual doped quartz powder, fly ash, and blast furnace slag also improved. MIP tests showed that mineral additives can change the pore size distribution after autoclave curing. However, the number of aching holes increased after mixing with 20% quartz powder and caused a decrease in the sulfate resistance.

scholarly journals Evolution of Mechanical Properties with Time of Fly-Ash-Based Geopolymer Mortars under the Effect of Granulated Ground Blast Furnace Slag Addition

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1135 ◽  
Author(s):  
Mateusz Sitarz ◽  
Izabela Hager ◽  
Marta Choińska
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Modulus Of Elasticity ◽  
Blast Furnace Slag ◽  
Energy Savings ◽  
Pulse Velocity ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Geopolymers are considered to alternatives to Portland cement, providing an opportunity to exploit aluminosilicate wastes or co-products with promising performances in the construction sector. This research is aimed at investigating the strength of fly-ash-geopolymers of different ages. The effect of granulated blast furnace slag (GGBFS) as a partial replacement of fly ash (FA) on the tensile (ft) and compressive strength (fc), as well as the modulus of elasticity, is investigated. The main advantage of the developed geopolymer mixes containing GGBFS is their ability to set and harden at room temperature with no need for heating to obtain binding properties, reducing the energy consumption of their production processes. This procedure presents a huge advantage over binders requiring heat curing, constituting a significant energy savings and reduction of CO2 emissions. It is found that the development of strength strongly depends on the ratio of fly-ash to granulated blast furnace slag. With the highest amount of GGBFS, the compressive strength of geopolymers made of fly-ash reached 63 MPa after 28 days of curing at ambient temperature. The evolution of compressive strength with time is correlated with the development of ultrasound pulse velocity methods, which are used to evaluate maturity. The modulus of elasticity changes with strength and the relationship obtained for the geopolymer is presented on the basis of typical models used for cement-based materials. The tensile to compressive strength ratios of the tested geopolymers are identified as higher than for cementitious binders, and the ft(fc) relationship is juxtaposed with dependencies known for cement binders, showing that the square root function gives the best fit to the results.

scholarly journals The Compressive Strength and Microstructure of Alkali-Activated Binary Cements Developed by Combining Ceramic Sanitaryware with Fly Ash or Blast Furnace Slag

Minerals ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 337 ◽  
Author(s):  
Juan Cosa ◽  
Lourdes Soriano ◽  
María Borrachero ◽  
Lucía Reig ◽  
Jordi Payá ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Calcium Content ◽  
Partial Replacement ◽  
Alkali Activation ◽  
High Calcium ◽  
Furnace Slag ◽  
Alkali Activated

The properties of a binder developed by the alkali-activation of a single waste material can improve when it is blended with different industrial by-products. This research aimed to investigate the influence of blast furnace slag (BFS) and fly ash (FA) (0–50 wt %) on the microstructure and compressive strength of alkali-activated ceramic sanitaryware (CSW). 4 wt % Ca(OH)2 was added to the CSW/FA blended samples and, given the high calcium content of BFS, the influence of BFS was analyzed with and without adding Ca(OH)2. Mortars were used to assess the compressive strength of the blended cements, and their microstructure was investigated in pastes by X-ray diffraction, thermogravimetry, and field emission scanning electron microscopy. All the samples were cured at 20 °C for 28 and 90 days and at 65 °C for 7 days. The results show that the partial replacement of CSW with BFS or FA allowed CSW to be activated at 20 °C. The CSW/BFS systems exhibited better mechanical properties than the CSW/FA blended mortars, so that maximum strength values of 54.3 MPa and 29.4 MPa were obtained in the samples prepared with 50 wt % BFS and FA, respectively, cured at 20 °C for 90 days.

scholarly journals Effect of Polypropylene Fiber, GGBS and Fly Ash over the Strength Aspects of Concrete: A Critical Review

2021 ◽  
Vol 9 (VI) ◽  
pp. 978-983
Author(s):  
Khalid Bashir Mir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Polypropylene Fiber ◽  
Synthetic Fiber ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

In this review study the usage of three different kinds of constructional materials was discussed in detail. The three materials comprised of Ground Granulated Blast Furnace Slag, fly and polypropylene fiber. Ground Granulated Blast Furnace Slag is basically the slag derived after the quenching process of iron slag produced during the processing of iron in iron industry. Fly ash is the waste generated from the coal processing industries and is mainly used in the road constructions works. Polypropylene fiber is a synthetic fiber that has very high tensile strength and flexural strength. This fiber is also known as synthetic fiber as it is mainly used in the synthetic industry. Depending upon the results of previous studies over the usage of these materials various conclusions has been drawn which are as follows. The results of studies related to the usage of Ground Granulated Blast Furnace Slag as partial replacement of cement concluded that the most optimum usage percentage of Ground Granulated Blast Furnace Slag as partial replacement of cement was found to be between 20 percent and 30 percent and beyond this limit the strength of concrete was decreasing. The past studies related to the usage of fly ash as partial replacement of cement shoed that the most optimum usage percentage of fly ash was found to be between 15 percent to 20 percent and beyond this percentage the strength parameters of concrete such as compressive strength, flexural strength and split tensile strength starts declining up to a greater extent. The studies related to the usage of polypropylene fiber showed that the usage of this fiber increases the compressive strength of soil and the most optimum results were found between 1.0 percent to 1.5 percent usages of polypropylene fiber. Above this percentage there will be negative effect on the strength aspects and the compressive strength starts declining.

scholarly journals New Composite Material for Masonry Repair: Mortar Formulations and Experimental Studies

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 912
Author(s):  
Walid Deboucha ◽  
Ibrahim Alachek ◽  
Jean-Patrick Plassiard ◽  
Olivier Plé
Keyword(s):  
Experimental Study ◽  
Composite Material ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Mechanical Performance ◽  
Experimental Studies ◽  
Uniaxial Tensile ◽  
Mineral Additives ◽  
Furnace Slag

The need for retrofitting existing masonry structures is progressively becoming more important due to their continuous deterioration or need to meet the current design requirements of Eurocodes. Textile-Reinforced Mortar (TRM) composite systems have emerged as a sustainable repair methodology suitable for structure retrofitting. Nevertheless, their mechanical performance is still far from being fully investigated. This paper presents an experimental study on the tensile and bond behaviors of a new mortar-based composite consisting of mineral additives, blended cement mortar, and stainless-steel grid. Three different mineral additives (silica fume, fly ash, and blast furnace slag), in binary and ternary systems were used. The experimental study included uniaxial tensile coupon testing on composite specimens and bond tests on composite material applied to clay-brick substrate. The results obtained with the different textile-reinforced cement-based mortars were compared and are discussed here. It was found that, for mortar formulations containing mineral additives—such as fly ash or blast-furnace slag—with high tensile and bond strengths, an adequate adherence between the constituents was obtained. The developed mortar presents mechanical performances equivalent to traditional mortars without additives. The study contributes to the existing knowledge regarding the structural behavior of TRM and promotes the development of a low impact carbon cementitious matrix.

scholarly journals Influence of Inter-Particle Distances on the Rheological Properties of Cementitious Suspensions

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7869
Author(s):  
Rajagopalan Sam Rajadurai ◽  
Su-Tae Kang
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Rheological Properties ◽  
Blast Furnace Slag ◽  
Fine Particles ◽  
Flow Characteristics ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Particle Sizes ◽  
Furnace Slag

Supplementary cementitious materials (SCMs), such as fly ash (FA), blast furnace slag (BS), and silica fume (SF), have been mostly used as a replacement for Portland cement (PC). Replacing the SCMs with cement can provide improved strength characteristics; however, their applicability depends on the flow characteristics of the fresh mixtures. In this study, the rheological performance of cementitious suspensions in paste scale with different water-to-solid (W/S) volume ratios, varied from 1.25, 1.50, 1.75, 2.00, 2.25, to 2.50, was evaluated. As a result of the rheological tests, the yield stress and plastic viscosity of PC, FA, BS, and SF suspensions decreased as the W/S ratio increased. This study also estimated the inter-particle distances of the cementitious suspensions, and their relationship to the rheological properties was established. The inter-particle distances of the PC, FA, BS, and SF suspensions were in the ranges of 5.74~14.67 µm, 5.18~11.66 µm, 3.82~9.34 µm, and 0.107~0.27 µm, respectively. For very fine particles with a large surface area, the sensitivity to the rheological properties was high and the sensitivity was low when the particle sizes increased, indicating that the rheological properties were more sensitive to fine particles.

Sign in / Sign up

Export Citation Format

Share Document