Thermoelectric Modules For High Temperature Waste Heat

2005 ◽  
Vol 886 ◽  
Author(s):  
Ryoji Funahashi ◽  
Toshiyuki Mihara ◽  
Masashi Mikami ◽  
Saori Urata
Keyword(s):  
Room Temperature ◽  
Open Circuit Voltage ◽  
Waste Heat ◽  
Thermal Strain ◽  
Thermoelectric Module ◽  
Internal Resistance ◽  
Open Circuit ◽  
Cold Side ◽  
Adhesive Material ◽  
Thermoelectric Modules

ABSTRACTA new adhesive material has been developed in order to obtain practically usable thermoelectric modules composed of oxide thermoelectric legs. The thermoelectric module composed of 8-pair oxide legs has been fabricated. Both hot- and cold-sides of the module were covered by alumina plates. Open circuit voltage VO and maximum power Pmax reach 0.38 V and 0.30 W, respectively at 803 K of a hot-side temperature TH and 362 K of a temperature differential ΔT between TH and cold-side temperature TC. Generating power was repeated 11 times at 873-993 K of TH and at 200-290 K of ΔT. The module was cooled down to room temperature after each generation. At third measurement internal resistance RI of the module increased by 30 %. This is due to destruction of junctions because of thermal strain. No deterioration, however, was observed in thermoelectric properties for the oxide legs.

Power Generation Using Oxide Thermoelectric Modules

2006 ◽  
Vol 46 ◽  
pp. 158-167 ◽  
Author(s):  
Ryoji Funahashi ◽  
Saori Urata ◽  
Toshiyuki Mihara ◽  
Naoki Nabeshima ◽  
Kanako Iwasaki
Keyword(s):  
Maximum Output Power ◽  
Internal Resistance ◽  
Open Circuit ◽  
Maximum Output ◽  
Cold Side ◽  
Thermoelectric Modules ◽  
Oxide Powders ◽  
Ag Electrodes ◽  
Ag Paste ◽  
P Type

Different versions of thermoelectric unicouples composed of p-type Ca3Co4O9 (Co-349) and n-type LaNiO3 (Ni-113) or CaMnO3 (Mn-113) bulk materials were prepared. In the unicouples p- and n-type legs were connected with Ag electrodes using Ag paste including various oxide powders with various ratios. For the Co-349/Ni-113 unicouples, maximum output power (Pmax) reaches 177mW at a hot side temperature (TH) of 1073K and a temperature differential (ΔT) between TH and cold side temperature of 500K at 6wt% of Co-349 powder. On the other hand, the lowest internal resistance (RI) is observed in a Co-349/Mn-113 unicouple prepared using Ag paste including 3wt% of Mn-113 powder. Thermoelectric modules consisting of 8 pairs of oxide legs were fabricated using the same method with the unicouples. The open circuit voltage (VO) and Pmax increase with increasing TH and reach 0.392 V and 0.314 W, and 0.911 V and 0.233 W at a TH of 1273 K in air for the Co-349/Ni-113 and Co-349/Mn-113 modules, respectively.

A Novel InSb Photodiode Infrared Sensor Operating at Room Temperature

2005 ◽  
Vol 891 ◽  
Author(s):  
Koichiro Ueno ◽  
Edson Gomes Camargo ◽  
Yoshifumi Kawakami ◽  
Yoshitaka Moriyasu ◽  
Kazuhiro Nagase ◽  
...  
Keyword(s):  
Room Temperature ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Consumer Electronics ◽  
Electronic Equipment ◽  
Personal Computers ◽  
Infrared Sensor ◽  
Output Noise ◽  
In Series ◽  
Photovoltaic Mode

ABSTRACTA microchip-sized InSb photodiode based infrared sensor (InSb PDS) that operates at room temperature was developed. The InSb PDS consists of 700 photodiodes connected in series and consumes no power, because it works in photovoltaic mode to output an open-circuit voltage. The InSb PDS has a typical responsivity of 1,900 V/W and an output noise of 0.15 μV/Hz1/2. A detectivity of 2.8×108 cmHz1/2/W was obtained at 300 K. The InSb PDS has performance high enough for applications such as mobile electronic equipment, personal computers, and consumer electronics

Estimating the Internal Resistance of Li-Ion Battery with Joule's Law to find the Open Circuit Voltage

2021 ◽  
Author(s):  
Venkata Nagarjun PM ◽  
Hirshik Ram S ◽  
Pratik Uthan ◽  
Veeramani V ◽  
Senthilkumar Subramaniam
Keyword(s):  
Open Circuit Voltage ◽  
Internal Resistance ◽  
Open Circuit ◽  
Li Ion Battery ◽  
Li Ion

Thermoelectric High Power Generating Module Made by n-Ba8AlxSi46-x Clathrate

2008 ◽  
Vol 1102 ◽  
Author(s):  
Shinji Munetoh ◽  
Makoto Arita ◽  
Hideki Makiyama ◽  
Teruaki Motooka
Keyword(s):  
Figure Of Merit ◽  
Open Circuit Voltage ◽  
Thermoelectric Module ◽  
Lithium Ion ◽  
Open Circuit ◽  
Electric Resistance ◽  
Thermoelectric Figure ◽  
Arc Melting ◽  
In Series ◽  
Specific Electric Resistance

AbstractWe have developed a new thermoelectric power-generating module composed of 72 pieces of n-type Ba8Al18Si28 clathrate elements made by arc melting. The Seebeck coefficient, specific electric resistance and thermal conductivity of Ba8Al18Si28 clathrate were 250 μV/K, 1.9 mΩcm and 3.1 W/mK at 500 °C, respectively, and the thermoelectric figure of merit (ZT) was 0.8. The new thermoelectric module was constructed using only n-type thermoelectric elements connected in series with hook-shaped electrodes. The open-circuit voltage of the module increased with hot-side temperature up to 1.8 V at 500 °C and generated 0.24 W. The module was successfully used to charge lithium-ion batteries for mobile phones.

Efficient Cu(In, Ga)Se2 Based Solar Cells Prepared by Electrodeposition

2003 ◽  
Vol 763 ◽  
Author(s):  
D. Guimard ◽  
N. Bodereau ◽  
J. Kurdi ◽  
J.F. Guillemoles ◽  
D. Lincot ◽  
...  
Keyword(s):  
Band Gap ◽  
Room Temperature ◽  
Open Circuit Voltage ◽  
Spectral Response ◽  
Deposition Process ◽  
Open Circuit ◽  
Response Analysis ◽  
Cell Parameters ◽  
Current Voltage ◽  
Capacitance Voltage

AbstractCuInSe2 and Cu(In, Ga)Se2 precursor layers have been prepared by electrodeposition, with morphologies suitable for device completion. These precursor films were transformed into photovoltaic quality films after thermal annealing without any post-additional vacuum deposition process. Depending on the preparation parameters annealed films with different band gaps between 1eV and 1.5 eV have been prepared. The dependence of resulting solar cell parameters has been investigated. The best efficiency achieved is about 10,2 % for a band gap of 1.45 eV. This device presents an open circuit voltage value of 740 mV, in agreement with the higher band gap value. Device characterisations (current-voltage, capacitance-voltage and spectral response analysis) have been performed. Admittance spectroscopy at room temperature indicates the presence of two acceptor traps at 0.3 and 0.43 eV from the valance band with density of the order of 2. 1017 cm-3 eV-1.

Thermoelectric Module of P-Type Ca-Co-O/N-Type ZnO Thin Films

2012 ◽  
Vol 622-623 ◽  
pp. 726-733 ◽  
Author(s):  
Weerasak Somkhunthot ◽  
Nuwat Pimpabute ◽  
Tosawat Seetawan
Keyword(s):  
Thin Films ◽  
Electrical Resistivity ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
Electrical Power ◽  
Thermoelectric Module ◽  
Preliminary Test ◽  
Internal Resistance ◽  
Open Circuit ◽  
P Type

Thin films thermoelectric module fabricated by pulsed-dc magnetron sputtering system using Ca3Co4O9(p-type) and ZnO (n-type) targets of 60 mm diameter and 2.5 mm thickness, which were made from powder precursor, and obtained by solid state reaction. Thin films of p-Ca-Co-O (Seebeck coefficient = 143.85 µV/K, electrical resistivity = 4.80 mΩm, power factor = 4.31 µW/m K2) and n-ZnO (Seebeck coefficient =229.24 µV/K, electrical resistivity = 5.93 mΩm, power factor = 8.86 µW/m K2) were used to make a thermoelectric module, which consist of four pairs of legs connected by copper electrodes (0.5 mm thickness, 3.0 mm width, and 3.0-8.0 mm length). Each leg is 3.0 mm width, 20.0 mm length, and 0.44 µm thickness on a glass substrate of 1.0 mm thickness in dimension 25.0x50.0 mm2. For preliminary test, a module was used to thermoelectric power generation. It was found that the open circuit voltage increased with increasing temperature difference from 3 mV at 5 K up to 20 mV at 78 K. The internal resistance of a module reached a value of 14.52 MΩ. This test indicated that a module can be generated the electrical power. Therefore, it can be used as an important platform for further thin films thermoelectric module research.

scholarly journals Effect of Different Operating Conditions on Performance of Commercial Low-Temperature Thermoelectric Modules

2019 ◽  
Vol 9 (2) ◽  
pp. 1781-1791
Keyword(s):  
Low Temperature ◽  
Conversion Efficiency ◽  
Power Output ◽  
Waste Heat ◽  
Thermoelectric Module ◽  
Operating Conditions ◽  
Maximum Power ◽  
Thermoelectric Modules ◽  
Temperature Range ◽  
Maximum Power Output

In the field of waste heat recovery, thermoelectric generators (TEG) are used to convert waste heat to electric power. This system attracts the attention of researchers to make it more and more efficient. The performance of thermoelectric module (TEM) plays a crucial role for thermoelectric system. Appropriate selection of thermoelectric module is one of the important criteria for enhancing the power output and conversion efficiency of thermoelectric generator. In this work, the effect of various operating conditions on performance of thermoelectric modules was experimentally investigated. Three commercial bismuth telluride (Bi2Te3 ) thermoelectric modules (TEM1, TEM2, and TEM3) were experimentally tested to find the best performance module for low-temperature waste heat. The open-circuit voltage, power output, and conversion efficiency were measured at various operating conditions. Different operating parameters such as water mass flow rate, heater voltage, hot and cold side temperature of thermoelectric module, and external load resistance were considered for this work. An electric heater was used as a heat source and water used as a cooling fluid at heat sink side. It was observed that the TEM1 shows maximum power output of 0.31, 0.71 and 1.25W, for temperature ranges of 80-100, 100-150, and 150-200 oC respectively. TEM3 achieved maximum power output 0.81W for temperature range of 100-150 oC. TEM1, TEM2 and TEM3 have the maximum conversion efficiency of 1.37, 0.60, and 1.64 % respectively. The TEM2 having less power output and conversion efficiency for temperature range of 80-200 oC compare to TEM1 and TEM3. However, the TEM1 is more appropriate for temperature range of 80-200 oC and the TEM3 is also suitable for the temperature range of 80-150 oC.

scholarly journals Temperature-Dependent Open-Circuit Voltage Measurements and Light-Soaking in Hydrogenated Amorphous Silcon Solar Cells

2005 ◽  
Vol 862 ◽  
Author(s):  
Jianjun Liang ◽  
E. A. Schiff ◽  
S. Guha ◽  
B. Yan ◽  
J. Yang
Keyword(s):  
Solar Cells ◽  
Amorphous Silicon ◽  
Room Temperature ◽  
Open Circuit Voltage ◽  
Hydrogenated Amorphous Silicon ◽  
Open Circuit ◽  
Illumination Intensity ◽  
Temperature Dependent ◽  
Defect Generation ◽  
Hydrogenated Amorphous

AbstractWe present temperature-dependent measurements of the open-circuit voltage VOC(T) in hydrogenated amorphous silicon nip solar cells prepared at United Solar. At room-temperature and above, VOC measured using near-solar illumination intensity differs by as much as 0.04 V for the as-deposited and light-soaked states; the values of VOC for the two states converge below 250 K. Models for VOC based entirely on recombination through deep levels (dangling bonds) do not account for the convergence effect. The convergence is present in a model that assumes the recombination traffic in the as-deposited state involves only bandtails, but which splits the recombination traffic fairly evenly between bandtails and defects for the light-soaked state at room-temperature. Recombination mechanisms are important in understanding light-soaking, and the present results are inconsistent with at least one well-known model for defect generation.

The Study of Cook-Stove Thermoelectric Generator Power

2014 ◽  
Vol 979 ◽  
pp. 421-425 ◽  
Author(s):  
Narong Sangwaranatee
Keyword(s):  
Heat Exchanger ◽  
Electric Power ◽  
Electric Current ◽  
Electrical Resistance ◽  
Thermoelectric Generator ◽  
Waste Heat ◽  
Thermoelectric Module ◽  
Cold Side ◽  
Heating Value ◽  
Power Rate

This research studies the alternative way of electricity generating from the waste heat of economy oven by using 4 modules of thermoelectric modules. The hot side of thermoelectric module is attached to the heat plate while the cold side is installed on the rectangular, plate-fin heat exchanger. Variety of system adjustments were used during this study in terms of finding the maximum electric power rate. Adjusting the heating value and the electrical resistance to the thermoelectric was the procedure in this study. From the research, we found out that at the temperature of 200°C on the heat pad, the released maximum electric current was 4.5 W. The percentage of heat converting to electric current was 11.9%, with the 0.84 A and 5.35 V. The efficiency of the economy oven was 23.20%, and comes up to 23.39% while generating power via thermoelectric module.

Sign in / Sign up

Export Citation Format

Share Document