Shape-Memory Properties of Radiopaque Micro-Composites from Amorphous Polyether Urethanes Designed for Medical Application

2009 ◽  
Vol 1190 ◽  
Author(s):  
Jing Cui ◽  
Karl Kratz ◽  
Andreas Lendlein
Keyword(s):  
Shape Memory ◽  
Polymer Composites ◽  
Medical Application ◽  
Tensile Tests ◽  
Barium Sulphate ◽  
Mechanical Analysis ◽  
Gravimetric Analysis ◽  
Micro Particles ◽  
Shape Memory Properties

AbstractBiocompatible shape-memory polymers are of high significance for application in medical devices or instruments for minimally invasive surgery. To follow the medical device placement or changes in shape of the device in vivo by imaging methods like X-ray techniques, radiopacity of the polymer is required. In this work, we explored the shape-memory properties of radiopaque polymer composites prepared by incorporation of barium sulphate micro-particles in a biomedical grade polyether urethane (PEU) by co-extrusion technique. The filler content was varied from 5 wt% to 40 wt%, which was confirmed by thermal gravimetric analysis (TGA) measurements, while the particle distribution was visualized by scanning electron microscopy (SEM). The thermal and mechanical properties of the composites were investigated by means of dynamic mechanical analysis at varied temperature (DMTA) and tensile tests. The shape-memory properties of PEU composites were quantified in cyclic, thermomechanical experiments. A significant increase in Young’s modulus and a decrease in elongation at break were observed for PEU composites with increasing content of BaSO4, while the DMTA results were not affected by incorporation of the fillers. All samples exhibited excellent shape-memory properties with shape fixity rates (Rf) above 98% and values for shape recovery rate (Rr) in the range of 81% to 93%. The maximum stress (σmax) obtained under constant strain recovery conditions increased from 0.6 MPa to 1.4 MPa with raising amount of BaSO4, while the corresponding temperature (Tσ,max) as well as the switching temperature (Tsw) determined under stress-free conditions remained constant for all polymer composites.

A strengthening approach for damping property and shape memory property of acrylic rubber/polylactide blends

2018 ◽  
Vol 51 (7-8) ◽  
pp. 626-643
Author(s):  
Chengliang Li ◽  
Xingxing Ji ◽  
Yang Lyu ◽  
Xinyan Shi
Keyword(s):  
Shape Memory ◽  
Loss Factor ◽  
Phenol Formaldehyde ◽  
Mechanical Analysis ◽  
Damping Properties ◽  
Shape Memory Property ◽  
Memory Property ◽  
Damping Material ◽  
Shape Memory Properties ◽  
Shape Memory Effects

In this work, a damping material was successfully prepared by blending acrylic rubber (ACM) and polylactide (PLA) with sulfur and soap salt as the curing agents. A phenol-formaldehyde (PF) resin was used as a modifier. The effects of PF on the mechanical properties, damping properties, compatibility and shape memory properties of the blends were studied. The compatibility and damping properties were characterized by dynamic mechanical analysis, Fourier transform infrared spectroscope and microstructure analysis. The shape memory properties were examined by thermal mechanical analyser. The results revealed that the tensile strength of the blends was decreased and the toughness was increased with the increase of PF loadings. The introduction of PF improved the compatibility between PLA and ACM, which was deduced from the fact that the glass transition temperature of ACM was increased and the two loss factor peaks became closer. It was also found that the loss factor peak became higher and the effective damping temperature range became wider due to the formation of hydrogen bonding, implying that the damping properties of ACM/PLA blends were significantly improved. The ACM/PLA blends exhibited good dual-shape memory effect and its shape recovery ratio was increased by introduction of PF and raising the trigger temperature. The blends also exhibited good triple-shape memory property, which was dramatically improved by the introduction of PF. The mechanisms for the enhanced shape memory effects were then analysed.

Preparation and Properties of Silane-Terminated Poly(urethane-Imide)

2013 ◽  
Vol 690-693 ◽  
pp. 1577-1580
Author(s):  
Xiao Xi Hu ◽  
Yun Wang
Keyword(s):  
Thermal Stability ◽  
Water Resistance ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Gravimetric Analysis ◽  
Thermal Gravimetric ◽  
Silane Coupling ◽  
Ft Ir ◽  
And Storage ◽  
Thermal Stability Of

A serious of silane-terminated poly (urethane-imide) (Si-PUI) was synthesized via prepolymer method using polycarbonatediols (PCDL), 2,4-tolylene diisocyanate (TDI), 4,4'-Oxydiphthalic Anhydride (ODPA) and silane coupling agent KH-550. The structure of the products was characterized by FT-IR. The thermal properties were measured by thermal gravimetric analysis (TGA). The thermal mechanical behavior was investigated by dynamic mechanical analysis (DMA).The mechanical characteristic was measured by tensile tests. The water absorption (Wa) was also been tested. With the imide content increasing, the thermal stability, tensile strength and storage modulus of poly (urethane-imide) improve significantly, and the glass transition temperature rises. The introduction of silanes improves the water resistance and further enhances the thermal stability of poly (urethane-imide).

Deep focusing on the role of microstructures in shape memory properties of polymer composites: A critical review

2019 ◽  
Vol 117 ◽  
pp. 280-303 ◽  
Author(s):  
Mahyar Panahi-Sarmad ◽  
Mahbod Abrisham ◽  
Mina Noroozi ◽  
Arian Amirkiai ◽  
Parham Dehghan ◽  
...  
Keyword(s):  
Shape Memory ◽  
Polymer Composites ◽  
Critical Review ◽  
Shape Memory Properties

scholarly journals Shape Memory Epoxy Polymer (SMEP) Composite Mechanical Properties Enhanced by Introducing Graphene Oxide (GO) into the Matrix

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1107 ◽  
Author(s):  
Zhengwei Yu ◽  
Zhenqing Wang ◽  
Hao Li ◽  
Jianxin Teng ◽  
Lidan Xu
Keyword(s):  
Graphene Oxide ◽  
Shape Memory ◽  
Polymer Composites ◽  
Epoxy Polymer ◽  
Mechanical Performance ◽  
Memory Performance ◽  
Mechanical Analysis ◽  
Tensile Fracture ◽  
Good Shape ◽  
The Matrix

Shape memory epoxy polymer (SMEP) composite specimens with different graphene oxide (GO) contents were manufactured to study the effects of GO mass fractions on epoxy polymer composites. While ensuring the shape memory effect of SMEP, the addition of GO also remarkably strengthened the mechanical performance of the polymers. Analyses of the epoxy polymer composites’ thermal, mechanical, and shape memory performance were conducted through carrying out dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), and static tensile, three-point bending, impact, and shape memory tests. Moreover, the tensile fracture, bending fracture, and impact fracture interfaces of epoxy resin composites were examined with scanning electron microscopy. The final test results indicated that when the GO content was 0.8 wt %, SMEP composites had good shape memory performance and optimum thermal and mechanical performance.

scholarly journals Mechanical, Thermal, and Shape Memory Properties of Three-Dimensional Printing Biomass Composites

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1234 ◽  
Author(s):  
Hongjie Bi ◽  
Min Xu ◽  
Gaoyuan Ye ◽  
Rui Guo ◽  
Liping Cai ◽  
...  
Keyword(s):  
Shape Memory ◽  
Wood Flour ◽  
Memory Performance ◽  
Thermoplastic Polyurethane ◽  
Tensile Elongation ◽  
Three Dimensional ◽  
Mechanical Analysis ◽  
Shape Memory Properties ◽  
Shape Memory Composites ◽  
Recovery Angle

In this study, a series of heat-induced shape memory composites was prepared by the hot-melt extrusion and three-dimensional (3D) printing of thermoplastic polyurethane (TPU) using wood flour (WF) with different contents of EPDM-g-MAH. The mechanical properties, microtopography, thermal property analysis, and heat-induced shape memory properties of the composites were examined. The results showed that, when the EPDM-g-MAH content was 4%, the tensile elongation and tensile strength of the composites reached the maximum value. The scanning electron microscopy and dynamic mechanical analysis results revealed a good interface bonding between TPU and WF when the EPDM-g-MAH content was 4%. The thermogravimetric analysis indicated that the thermal stability of TPU/WF composites was enhanced by the addition of 4% EPDM-g-MAH. Heat-induced shape memory test results showed that the shape memory performance of composites with 4% EPDM-g-MAH was better than that of unmodified-composites. The composites’ shape recovery performance at a temperature of 60 °C was higher than that of the composites at ambient temperature. It was also found that, when the filling angle of the specimen was 45°, the recovery angle of the composites was larger.

Study on Shape Memory Effects of LC Epoxy Resins with Lateral Substituents

2010 ◽  
Vol 428-429 ◽  
pp. 391-393 ◽  
Author(s):  
Li Yan Liang ◽  
De Wen Zhou ◽  
Man Geng Lu
Keyword(s):  
Shape Memory ◽  
Dynamic Mechanical Analysis ◽  
Epoxy Resins ◽  
Liquid Crystalline ◽  
Mechanical Analysis ◽  
Memory Effects ◽  
Ordered Structures ◽  
Alkyl Groups ◽  
Shape Memory Properties ◽  
Shape Memory Effects

A series of shape memorized liquid crystalline epoxides with different length of lateral substituents were prepared with several kinds of hardener. The dynamic mechanical analysis and the sharp memory properties of the resulted LC epoxy resins were studied by POM, WAXD, DSC and DMA. The results showed that the modulus in the rubbery region (ER) of the LC epoxides decreases as the length of lateral alkyl groups increases. And the shape memory properties were strongly impacted not only by the length of lateral substituents, but also by the kinds of hardener. The recovering speeds of the shape-memory liquid crystalline epoxides decrease as the increasing length of lateral alkyl groups. And recovering speeds of LC epoxides cured with aromatic amine (DDM) are faster than that of LC epoxides cured with anhydride (THHPA). The local ordered structures and the lateral substituents played an important role in shape memory effects.

The Two-Stage Curing Method for Shape-Memory Materials

2012 ◽  
Vol 476-478 ◽  
pp. 2227-2230
Author(s):  
He Sun ◽  
Yu Yan Liu ◽  
Hui Feng Tan ◽  
Chang Guo Wang
Keyword(s):  
Shape Memory ◽  
Memory Performance ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Two Stage ◽  
Memory Tests ◽  
Second Stage ◽  
Shape Memory Properties ◽  
Shape Memory Materials ◽  
Curing Method

In this paper, a various shape-memory materials had been prepared by two-stage curing method. The purpose of using this approach was to maintain the excellent shape memory properties and low glass transition temperature (Tg) of shape-memory materials after first stage curing, furthermore, improve the Tg and heat resistence effectively after second stage curing. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and fold-deploy shape memory tests were used to characterize the feasibility of two-stage curing, thermodynamics properties and shape memory performance of these polymers. DSC results showed that two different curing stages could be achieved successfully, DMA results suggested that heat resistance of materials had been improved after second curing stage, while the fold-deploy shape memory tests proved that the composites possessed excellent shape memory properties, it could be deformed into different shape and recovered its original shape fully within three minutes.

Martensitic Transformation and Mechanical Properties of Fe-added Au-Cu-Al Shape Memory Alloy with Various Heat Treatment Conditions

2014 ◽  
Vol 1760 ◽  
Author(s):  
Akira Umise ◽  
Masaki Tahara ◽  
Kenji Goto ◽  
Tomonari Inamura ◽  
Hideki Hosoda
Keyword(s):  
Heat Treatment ◽  
Cold Rolling ◽  
Shape Memory ◽  
Yield Stress ◽  
Mechanical Treatment ◽  
Tensile Tests ◽  
Treatment Temperature ◽  
Shape Memory Properties ◽  
Cold Rolled ◽  
Thermo Mechanical Treatment

ABSTRACTIn order to improve shape memory properties of Au-Cu-Al based shape memory alloys, the possibility to utilize thermo-mechanical treatment was investigated in this study, and effects of heat-treatment temperature on microstructure, martensitic transformation and mechanical properties of cold-rolled Au-30Cu-18Al-2Fe (AuCuAlFe) alloy were clarified by X-ray diffraction analysis (XRD, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and tensile tests at room temperature (RT). Here, Fe addition to AuCuAl improves ductility. Cold rolling with the thickness reduction of 30% was successfully carried out in AuCuAlFe at RT. An exothermic heat was observed in DSC at temperature from 402K, suggesting that recovery started at 402K. Besides, the transformation temperature hysteresis increased by the cold-rolling. The alloy was completely recrystallized after the heat treatment at 573K for 3.6ks. Tensile tests revealed that the yield stress was raised by cold rolling and largely by the subsequent heat treatment at 433K, which corresponded to the recovery start temperature by DSC. The yield stress decreased with increasing heat treatment temperature over 453K, probably due to recrystallization. AuCuAlFe cold-rolled and subsequent heat-treated at 573K exhibited the lowest yield stress as well as stress-plateau region, indicating that the thermo-mechanical treatment is effective to improve shape memory properties of Au-Cu-Al based alloys.

Sign in / Sign up

Export Citation Format

Share Document