Fermi Level Effects on Dislocation Formation in InAs1−xSbx Grown by MOCVD

1991 ◽  
Vol 240 ◽  
Author(s):  
R. M. Biefeld ◽  
T. J. Drummond
Keyword(s):  
Fermi Level ◽  
Carrier Concentration ◽  
Chemical Vapor ◽  
Layer Growth ◽  
Buffer Layers ◽  
Organic Chemical ◽  
Intrinsic Carrier Concentration ◽  
Strained Layer Superlattice ◽  
P Type ◽  
Dislocation Formation

ABSTRACTDislocation formation in InAs1−xSbx buffer layers grown on InSb substrates by metal-organic chemical vapor deposition is shown to be reproducibly enhanced by p-type doping at levels exceeding the intrinsic carrier concentration at the growth temperature. To achieve a carrier concentration greater than 2 × 1018 cm−3, the intrinsic carrier concentration of InSb at 475 C, p-type doping with diethylzinc was used. Carrier concentrations up to 6 × 1018 cm−3 were obtained. The zinc doped buffer layers have proven to be reproducibly crack free for InAs1−xSbx step graded buffer layers with a final composition of x = 0.12 lattice matched to a strained layer superlattice (SLS) with an average composition of x = 0.09. These structures have been used to prepare infrared photodiodes. Details of the buffer layer growth, an explanation for the observed Fermi level effect and the growth and characterization of an infrared photodiode are discussed.

Epitaxial GaN Layer Growth Using Nitrogen Enriched TiN Buffer Layers

2006 ◽  
Vol 916 ◽  
Author(s):  
Kazuhiro Ito ◽  
Yu Uchida ◽  
Sang-jin Lee ◽  
Susumu Tsukimoto ◽  
Yuhei Ikemoto ◽  
...  
Keyword(s):  
Buffer Layer ◽  
Light Emission ◽  
Chemical Vapor ◽  
Nucleation Site ◽  
Layer Growth ◽  
Buffer Layers ◽  
Organic Chemical ◽  
Nitrogen Enrichment ◽  
Threading Dislocation ◽  
Sapphire Substrates

AbstractAbout 20 years ago, the discovery of an AlN buffer layer lead to the breakthrough in epitaxial growth of GaN layers with mirror-like surface, using a metal organic chemical vapor deposition (MOCVD) technique on sapphire substrates. Since then, extensive efforts have been continued to develop a conductive buffer layer/substrate for MOCVD-grown GaN layers to improve light emission of GaN light-emitting diodes. In the present study, we produced MOCVD-grown, continuous, flat epitaxial GaN layers on nitrogen enriched TiN buffer layers with the upper limit of the nitrogen content of TiN deposited at room temperature (RT) on sapphire substrates. It was concluded that the nitrogen enrichment would reduce significantly the TiN/GaN interfacial energy. The RT deposition of the TiN buffer layers suppresses their grain growth during the nitrogen enrichment and the grain size refining must increase nucleation site of GaN. In addition, threading dislocation density in the GaN layers grown on TiN was much lower than that in the GaN layers grown on AlN.

{10} edge dislocations in YSZ films grown on (100)MgO by PLD

1994 ◽  
Vol 52 ◽  
pp. 530-531
Author(s):  
Jason R. Heffelfinger ◽  
C. Barry Carter
Keyword(s):  
Thin Films ◽  
Semiconductor Lasers ◽  
Vapor Deposition ◽  
Substrate Surface ◽  
Laser System ◽  
Average Energy ◽  
Target Material ◽  
Chemical Vapor ◽  
Buffer Layers ◽  
Organic Chemical

Yttria-stabilized zirconia (YSZ) is currently used in a variety of applications including oxygen sensors, fuel cells, coatings for semiconductor lasers, and buffer layers for high-temperature superconducting films. Thin films of YSZ have been grown by metal-organic chemical vapor deposition, electrochemical vapor deposition, pulse-laser deposition (PLD), electron-beam evaporation, and sputtering. In this investigation, PLD was used to grow thin films of YSZ on (100) MgO substrates. This system proves to be an interesting example of relationships between interfaces and extrinsic dislocations in thin films of YSZ.In this experiment, a freshly cleaved (100) MgO substrate surface was prepared for deposition by cleaving a lmm-thick slice from a single-crystal MgO cube. The YSZ target material which contained 10mol% yttria was prepared from powders and sintered to 85% of theoretical density. The laser system used for the depositions was a Lambda Physik 210i excimer laser operating with KrF (λ=248nm, 1Hz repetition rate, average energy per pulse of 100mJ).

scholarly journals Oxide p-n Heterojunction of Cu2O/ZnO Nanowires and Their Photovoltaic Performance

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Seung Ki Baek ◽  
Ki Ryong Lee ◽  
Hyung Koun Cho
Keyword(s):  
Solar Cell ◽  
Photovoltaic Performance ◽  
Wavelength Region ◽  
Chemical Vapor ◽  
Zno Nanowires ◽  
Organic Chemical ◽  
Glass Substrates ◽  
Constant Ph ◽  
Ito Glass ◽  
P Type

Oxide p-n heterojunction devices consisting of p-Cu2O/n-ZnO nanowires were fabricated on ITO/glass substrates and their photovoltaic performances were investigated. The vertically arrayed ZnO nanowires were grown by metal organic chemical vapor deposition, which was followed by the electrodeposition of the p-type Cu2O layer. Prior to the fabrication of solar cells, the effect of bath pH on properties of the absorber layers was studied to determine the optimal condition of the Cu2O electrodeposition process. With the constant pH 11 solution, the Cu2O layer preferred the (111) orientation, which gave low electrical resistivity and high optical absorption. The Cu2O (pH 11)/ZnO nanowire-based solar cell exhibited a higher conversion efficiency of 0.27% than the planar structure solar cell (0.13%), because of the effective charge collection in the long wavelength region and because of the enhanced junction area.

scholarly journals The Growth of InAsSb/InGaAs Strained-Layer Superlattices by Metal-Organic Chemical Vapor Deposition

1993 ◽  
Vol 325 ◽  
Author(s):  
R. M. Biefeld ◽  
K. C. Baucom ◽  
S. R. Kurtz ◽  
D. M. Follstaedt
Keyword(s):  
Chemical Vapor Deposition ◽  
Thermodynamic Model ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Organic Chemical ◽  
Strained Layer ◽  
Strained Layer Superlattice ◽  
Metal Organic ◽  
Strained Layer Superlattices ◽  
Organic Chemical Vapor Deposition

AbstractWe have grown InAsl-xSbx/Inl-yGayAs strained-layer superlattice (SLS) semiconductors lattice matched to InAs using a variety of conditions by metal-organic chemical vapor deposition. The V/III ratio was varied from 2.5 to 10 at a temperature of 475 °C, at pressures of 200 to 660 torr and growth rates of 3 - 5 A/s and layer thicknesses ranging from 55 to 152 Å. The composition of the InAsSb ternary can be predicted from the input gas molar flow rates using a thermodynamic model. At lower temperatures, the thermodynamic model must be modified to take account of the incomplete decomposition of arsine and trimethylantimony. Diodes have been prepared using Zn as the p-type dopant and undoped SLS as the n-type material. The diode was found to emit at 3.56 μm. These layers have been characterized by optical microscopy, SIMS, x-ray diffraction, and transmission electron diffraction. The optical properties of these SLS's were determined by infrared photoluminescence and absorption measurements.

scholarly journals Investigation of AlGaN/GaN Heterostructures Grown on Sputtered AlN Templates with Different Nucleation Layers

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4050 ◽  
Author(s):  
Chuan-Yang Liu ◽  
Ya-Chao Zhang ◽  
Sheng-Rui Xu ◽  
Li Jiang ◽  
Jin-Cheng Zhang ◽  
...  
Keyword(s):  
Chemical Vapor ◽  
Optimal Growth ◽  
Growth Conditions ◽  
Layer Growth ◽  
Organic Chemical ◽  
Propagation Mechanism ◽  
Nucleation Layer ◽  
Low Dislocation Density ◽  
Structural And Electrical Properties ◽  
Metal Organic

In this work, a sputtered AlN template is employed to grow high-quality AlGaN/GaN heterostructures, and the effects of AlN nucleation layer growth conditions on the structural and electrical properties of heterostructures are investigated in detail. The optimal growth condition is obtained with composited AlN nucleation layers grown on a sputtered AlN template, resulting in the smooth surface morphology and superior transport properties of the heterostructures. Moreover, high crystal quality GaN material with low dislocation density has been achieved under the optimal condition. The dislocation propagation mechanism, stress relief effect in the GaN grown on sputtered AlN, and metal organic chemical vapor deposition AlN nucleation layers are revealed based on the test results. The results in this work demonstrate the great potential of AlGaN/GaN heterostructures grown on sputtered AlN and composited AlN nucleation layers for microelectronic applications.

Characterization of Gan/Sapphire Interface and the Buffer Layer by TEM/AFM

2001 ◽  
Vol 7 (S2) ◽  
pp. 330-331
Author(s):  
B. Shea ◽  
Q. Sun-Paduano ◽  
D. F. Bliss ◽  
M. C. Callahan ◽  
C. Sung
Keyword(s):  
Buffer Layer ◽  
Gas Flow ◽  
Chemical Vapor ◽  
Wide Band ◽  
Buffer Layers ◽  
Organic Chemical ◽  
Wide Band Gap ◽  
Tem Analysis ◽  
Flow Rates ◽  
Device Applications

Interest in wide band gap III-V nitride semiconductor devices is increasing for optoelectronic and microelectronic device applications. to ensure the highest quality, TEM analysis can characterize the substrate and buffer layer interface. Measurements taken by TEM reveal the density of dislocations/cm2 and the orientation of Burger's vectors. This information allows for changes to be made in deposition rates, temperatures, gas flow rates, and other parameters during the processing.The GaN/sapphire samples grown at AFRL were produced in two consecutive steps, first to provide a thin buffer layer, and the other to grow a lum thick epitaxial film. Both growth steps were prepared using metallic organic chemical vapor deposition (MOCVD) in a vertical reactor. Buffer layers were prepared using a range of temperatures from 525 to 535°C and with a range of flow rates and pressures in order to optimize the nucleation conditions for the epitaxial films.

Metal-Organic chemical vapor deposition of BN on sapphire and its heterostructures with 2D and 3D materials

MRS Advances ◽  
2016 ◽  
Vol 1 (32) ◽  
pp. 2273-2283
Author(s):  
Qing Paduano ◽  
Michael Snure
Keyword(s):  
Electron Mobility ◽  
Substrate Surface ◽  
Chemical Vapor ◽  
High Electron Mobility Transistor ◽  
Layer Growth ◽  
Organic Chemical ◽  
Layer By Layer ◽  
High Electron ◽  
Two Dimensional ◽  
Direct Growth

ABSTRACTWe studied MOCVD processing for direct growth of BN on 2” sapphire substrates as a template for heterostructures with two dimensional (2D) and three dimensional (3D) materials. The combined experimental evidence points to three growth modes for BN: self-terminating, 3D random, and layer-by-layer, all of which are dependent on V/III ratio, temperature, pressure, and substrate surface modification via nitridation. At moderate temperature (950-1050°C), BN growth using high V/III ratio is self-terminating, resulting in c-oriented films aligned in-plane with respect to the orientation of the sapphire substrate. BN films grown under low V/III ratios are 3D, randomly oriented, and nano-crystalline. At higher temperature (1100°C), self-terminating growth transitions to a continuous layer-by-layer growth mode. When BN growth is self-terminating, films exhibit atomically smooth surface morphology and highly uniform thickness over a 2” sapphire wafer. Using these BN/sapphire templates we studied the growth of 2D and 2D/3D heterostructures. To study direct growth of 2D on 2D layered material we deposited graphene on BN in a continued process within the same MOCVD system. Furthermore, we explore the growth and nucleation of 3D materials (GaN and AlN) on BN. AlGaN/GaN based high electron mobility transistor (HEMT) structures grown on BN/sapphire exhibited two-dimensional electron gas characteristics at the AlGaN/GaN heterointerface, with room-temperature electron mobility and sheet electron density about 1900cm2/Vs and 1x1013cm-2, respectively.

Sign in / Sign up

Export Citation Format

Share Document