Texturing and Dielectric Properties of Laser Deposited BaTiO3 Thin Films Grown on Heated Substrates

1991 ◽  
Vol 243 ◽  
Author(s):  
M.D. Vaudin ◽  
L.P. Cook ◽  
W. Wong-Ng ◽  
P.K. Schenck ◽  
P.S. Brody ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Dielectric Properties ◽  
Electrical Properties ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Electrical Measurements ◽  
X Ray

AbstractThin films of BaTiO3 were deposited on platinum-coated silicon substrates using pulsed laser deposition and characterized using electron microscopy, powder x-ray diffraction and electrical measurements. The microstructure consisted of columnar BaTiO3 grains oriented normal to the substrate. Two preferred orientations were observed, with either the (001) or (111) planes of BaTiO3 being parallel to the substrate. The electrical properties of two films were measured and it was found that the (111) film was ferroelectric and the (001) film was not. Possible reasons for this are discussed.

Pulsed laser deposition and characterization of conductive RuO2 thin films

1997 ◽  
Vol 12 (6) ◽  
pp. 1433-1436 ◽  
Author(s):  
A. Iembo ◽  
F. Fuso ◽  
E. Arimondo ◽  
C. Ciofi ◽  
G. Pennelli ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Electrical Properties ◽  
Pulsed Laser Deposition ◽  
Photoelectron Spectroscopy ◽  
Pulsed Laser ◽  
Surface Characteristics ◽  
Laser Deposition ◽  
X Ray ◽  
Substrate Interface

RuO2 thin films have been produced on silicon-based substrates by in situ pulsed laser deposition for the first time. The electrical properties, the surface characteristics, the crystalline structure, and the film-substrate interface of deposited samples have been investigated by 4-probe resistance versus temperature technique, scanning electron microscopy, x-ray photoelectron spectroscopy, x-ray diffraction, and transmission electron microscopy, respectively. The films show good electrical properties. The RuO2-substrate interface is very thin (≈3 nm), since it is not degraded by any annealing process. These two characteristics render our films suitable to be used as electrodes in PZT-based capacitors.

Effect of Cu Dopant on the Electrical Property of ZnO Thin Films Deposited by Pulsed Laser Deposition

2007 ◽  
Vol 124-126 ◽  
pp. 339-342
Author(s):  
Gun Hee Kim ◽  
Hong Seong Kang ◽  
Dong Lim Kim ◽  
Hyun Woo Chang ◽  
Byung Du Ahn ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Zno Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Doped Zno ◽  
Deposition Conditions

Cu-doped ZnO (denoted by ZnO:Cu) films have been prepared by pulsed laser deposition using 3 wt. CuO doped ZnO ceramic target. The carrier concentrations (1011~1018 cm-3) and, electrical resistivity (10-1~105 cm) of deposited Cu-doped ZnO thin films were varied depending on deposition conditions. Variations of electrical properties of Cu-doped ZnO indicate that copper dopants may play an important role in determining their electrical properties, compared with undoped films. To investigate effects of copper dopants on the properties of ZnO thin films, X-Ray diffraction (XRD), photoluminescence (PL), and Hall measurements have been performed and corresponded.

The Structure and Electric Field Dependent Dielectric Properties of Annealed Sr1−xBaxTio3 Ferroelectric Thin Films

1995 ◽  
Vol 401 ◽  
Author(s):  
L.A. Knauss ◽  
J.M. Pond ◽  
J.S. Horwitz ◽  
C.H. Mueller ◽  
R.E. Treece ◽  
...  
Keyword(s):  
Thin Films ◽  
Dielectric Properties ◽  
Single Phase ◽  
Pulsed Laser ◽  
Lattice Parameter ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Deposited Films ◽  
Post Deposition

AbstractThe effect of a post deposition anneal on the structure and dielectric properties of epitaxial Sr1−x, BaxTiO3 (SBT) thin films with x = 0.35, 0.50 and 0.60 has been measured. The films were grown by pulsed laser deposition on LaAlO3(001) substrates at 750°C in 350 mTorr of oxygen. The asdeposited films were single phase, (001) oriented with 0)-scan widths for the (002) reflection between 0.160 and 0.50'. The dielectric properties of the as-deposited films exhibit a broad temperature dependence and a peak which is as much as 50 K below the peak in bulk SBT. Also, the lattice parameter, as measured by x-ray diffraction, of the as-deposited films was larger than the bulk indicating strain in the films. The as-deposited films were annealed for 8 hours at 900°C in oxygen. The dielectric properties of the annealed films were closer to that of bulk SBT and the lattice parameter was closer to the bulk lattice parameter indicating a reduction of strain. Annealing of as-deposited films also resulted in an increased dielectric tuning without increased dielectric loss.

Frequency and Temperature Dependence of Dielectric Properties of Orthorhombic HoMnO3 Thin Films

2014 ◽  
Vol 1025-1026 ◽  
pp. 427-431
Author(s):  
Ping Gao ◽  
Wei Zhang ◽  
Wei Tian Wang
Keyword(s):  
Dielectric Properties ◽  
Pulsed Laser ◽  
Signal Amplitude ◽  
Debye Model ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Cole Diagram

Orthorhombic HoMnO3 films were prepared epitaxially on Nb-doped SrTiO3 single crystal substrates by using pulsed laser deposition technique. The films showed perfectly a-axis crystallographic orientations. X-ray diffraction and atomic force microscopy were used to characterize the films. The complex dielectric properties were measured as functions of frequency (40 Hz~1 MHz) and temperature (80 K~300 K) with a signal amplitude of 50 mv. The respective dielectric relaxation peaks shifted to higher frequency as the measuring temperature increased, with the same development of real part of the complex permittivity. The cole-cole diagram was obtained according to the Debye model, and the effects of relaxation process were discussed.

Crystallization of Zn-rich and P-rich amorphous Zn3P2 thin films

1988 ◽  
Vol 66 (5) ◽  
pp. 373-375 ◽  
Author(s):  
C. J. Arsenault ◽  
D. E. Brodie
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Activation Energy ◽  
Electrical Properties ◽  
Structural Properties ◽  
Crystallization Process ◽  
X Ray Diffraction ◽  
Electrical Measurements ◽  
Conductivity Activation Energy ◽  
X Ray

Zn-rich and P-rich amorphous Zn3P2 thin films were prepared by co-evaporation of the excess element during the normal Zn3P2 deposition. X-ray diffraction techniques were used to investigate the structural properties and the crystallization process. Agglomeration of the excess element within the as-made amorphous Zn3P2 thin film accounted for the structural properties observed after annealing the sample. Electrical measurements showed that excess Zn reduces the conductivity activation energy and increases the conductivity, while excess P up to 15 at.% does not alter the electrical properties significantly.

Study of Raman Spectrum of Fe Doped CeO2 Thin Films Grown by Pulsed Laser Deposition

2010 ◽  
Vol 123-125 ◽  
pp. 375-378 ◽  
Author(s):  
Ram Prakash ◽  
Shalendra Kumar ◽  
Chan Gyu Lee ◽  
S.K. Sharma ◽  
Marcelo Knobel ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Single Phase ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Fe Doping ◽  
Full Width ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
X Ray

Ce1-xFexO2 (x=0, 0.01, 0.03 and 0.0 5) thin films were grown by pulsed laser deposition technique on Si and LaAlO3 (LAO) substrates. These films were deposited in vacuum and 200 mTorr oxygen partial pressure for both the substrates. These films were characterized by x-ray diffraction XRD and Raman spectroscopy measurements. XRD results reveal that these films are single phase. Raman results show F2g mode at ~466 cm-1 and defect peak at 489 cm-1 for film that deposited on LAO substrates, full width at half maximum (FWHM) is increasing with Fe doping for films deposited on both the substrates.

Fabrication of Ni–Al thin films by the pulsed laser deposition technique

1992 ◽  
Vol 7 (10) ◽  
pp. 2639-2642 ◽  
Author(s):  
R.K. Singh ◽  
Deepika Bhattacharya ◽  
S. Sharan ◽  
P. Tiwari ◽  
J. Narayan
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Rutherford Backscattering Spectrometry ◽  
Pulsed Laser ◽  
High Energy ◽  
Laser Deposition ◽  
Nanosecond Laser ◽  
X Ray ◽  
Target Composition

We have fabricated Ni3Al and NiAl thin films on different substrates by the pulsed laser deposition (PLD) technique. A high energy nanosecond laser beam was directed onto Ni–Al (NiAl, Ni3Al) targets, and the evaporated material was deposited onto substrates placed parallel to the target. The substrate temperature was varied between 300 and 400 °C, and the substrate-target distance was maintained at approximately 5 cm. The films were analyzed using scanning electron microscopy, transmission electron microscopy, x-ray diffraction, and Rutherford backscattering spectrometry. At energy densities slightly above the evaporation threshold, a slight enrichment of Al was observed, while at higher energy densities the film stoichiometry was close (<5%) to the target composition. Barring a few particles, the surface of the films exhibited a smooth morphology. X-ray and TEM results corroborated the formation of Ni3Al and NiAl films from similar target compositions. These films were characterized by small randomly oriented grains with grain size varying between 200 and 400 Å.

CRYSTALLINE SrTiO3 THIN FILMS ON SILICON BY PULSED LASER DEPOSITION

2005 ◽  
Vol 19 (01n03) ◽  
pp. 533-535
Author(s):  
J. H. HAO ◽  
J. GAO
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Perovskite Oxide ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Silicon Materials

We have developed a process to grow SrTiO 3 ( STO ) thin films showing single (110) orientation directly on Si by means of pulsed laser deposition technique. The growth of STO films directly on Si has been described. The crystallinity of the grown STO films was characterized by X-ray diffraction analysis of θ-2θ scan and rocking curve. Our results may be of interest for better understanding of the growth based on the perovskite oxide thin films on silicon materials.

scholarly journals Properties of Nanostructure Bismuth Telluride Thin Films Using Thermal Evaporation

2017 ◽  
Vol 2017 ◽  
pp. 1-4 ◽  
Author(s):  
Swati Arora ◽  
Vivek Jaimini ◽  
Subodh Srivastava ◽  
Y. K. Vijay
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Bismuth Telluride ◽  
Room Temperature ◽  
Thermal Evaporation ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Thermal Evaporation Method ◽  
X Ray ◽  
Scanning Electron

Bismuth telluride has high thermoelectric performance at room temperature; in present work, various nanostructure thin films of bismuth telluride were fabricated on silicon substrates at room temperature using thermal evaporation method. Tellurium (Te) and bismuth (Bi) were deposited on silicon substrate in different ratio of thickness. These films were annealed at 50°C and 100°C. After heat treatment, the thin films attained the semiconductor nature. Samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM) to show granular growth.

Thermoelectric Properties of C-Axis-Oriented Ca3Co4O9+δ Films Grown on MgO-Buffered Si (100) by PLD Technique

2010 ◽  
Vol 29-32 ◽  
pp. 1913-1918
Author(s):  
Xia Zhang ◽  
Hong Chen ◽  
Qiu Hui Liao ◽  
Xia Li
Keyword(s):  
Thin Films ◽  
State Of The Art ◽  
Pulsed Laser ◽  
Buffer Layers ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
High Quality ◽  
X Ray ◽  
Current State ◽  
Good Crystallinity

High-quality c-axis-oriented Ca3Co4O9+δ thin films have been grown directly on Si (100) wafers with inserting MgO buffer layers by pulsed-laser deposition (PLD). X-ray diffraction and scan electron microscopy show good crystallinity of the Ca3Co4O9+δ films. The resistivity and Seebeck coefficient of the Ca3Co4O9+δ thin films on Si (100) substrates are 9.8 mΩcm and 189 μV/K at the temperature of 500K, respectively, comparable to the single-crystal samples. This advance demonstrates the possibility of integrating the cobaltate-based high thermoelectric materials with the current state-of-the-art silicon technology for thermoelectricity-on-a-chip applications.

Sign in / Sign up

Export Citation Format

Share Document