Thermally Activated Processes and Dislocation Mobilities in Two-Phase γ-Titanium Aluminides

1994 ◽  
Vol 364 ◽  
Author(s):  
Fritz Appel ◽  
Ulf Sparka ◽  
Richard Wagner

AbstractThe processes controlling the dislocation mobility in two-phase γ-titanium aluminides have been investigated over a wide temperature range by determining the activation volumes and activation energies of thermally activated dislocation glide processes. The deformation tests are supplemented by electron microscope observations. Accordingly, at room temperature the mobility of ordinary dislocations is determined by a combination of localized pinning and lattice friction. Additional glide resistance arises from dislocation dipoles and debris defects, which are trailed and terminated at jogs in 1/2 <110] screw dislocations. Dislocation climb processes start above 900 K and seem to initiate the transition from brittle to ductile material behaviour.

1990 ◽  
Vol 5 (6) ◽  
pp. 1189-1196 ◽  
Author(s):  
M. Takeyama ◽  
C. T. Liu

The microstructure and mechanical properties of several Ni–Al–Hf alloys in the composition range between NiAl (β) and Ni2AlHf (Heusler phase) have been studied. The volume fraction of Heusler phase, Vf, in these alloys varies from about 15 to 96%. The lattice misfit between the β and Heusler phases in two-phase alloys is larger than 5%, indicating no coherency between them. The yield strength increases with increasing Vf at all temperatures to 1000°C. Compressive ductilities of 4 and 7% were obtained for the alloy with Vf of 15% at room temperature and 500°C, respectively, but they decreased to 0% with increasing Vf to 96%. The corresponding fracture mode is basically transgranular cleavage. However, all the alloys can be deformed extensively without fracture at 1000°C. The hardness of the Heusler alloy is very high (8.3 GPa) at room temperature, and it decreases gently with temperature to 600°C, followed by a rapid decrease to 1000°C. The brittleness and high hardness of the Ni2AlHf Heusler phase at low temperatures are interpreted in terms of internal lattice distortion resulting from its crystal structure. The thermally activated process of deformation takes place above 600°C, which is responsible for the rapid drop of the hardness of the alloys.


2002 ◽  
Vol 753 ◽  
Author(s):  
J. Müllauer ◽  
F. Appel

ABSTRACTIn two-phase titanium aluminide alloys, the implementation of precipitation reactions is a widely utilized concept to control the microstructure and strengthen the material. A study has been made on the influence of carbide and boride precipitates on dislocation mobility and strengthening at 300 K. Compression tests were carried out for characterizing the mechanisms determining flow stress and dislocation glide resistance. The interaction mechanisms between the precipitates and dislocations were assessed by thermodynamic glide parameters and transmission electron microscopy. It has been shown that small titanium boride precipitates and carbide precipitates of perovskite type act as long-range dislocation glide obstacles. The interaction between the dislocations and the borides and carbides mainly leads to an athermal stress contribution. However, the dislocation-particle interactions are quite different. Small groups of borides are encircled by dislocations. This gives rise to the formation of loop structures the density of which increases with strain. On the contrary, the carbide precipitates are shearable and can be overcome without Orowan looping. This different behaviour is also reflected in the work hardening characteristics. Whereas the work hardening coefficient of the boron doped material increases with increasing B-concentration, it is independent of concentration in the case of the carbon-doped material.


1994 ◽  
Vol 364 ◽  
Author(s):  
Marc Legros ◽  
Daniel Caillard ◽  
Alain Couret

AbstractIn situ deformation experiments have been performed on a two-phase Ti-23.7Al-9.4Nb (%at) alloy at room temperature. Dislocation glide processes in each phase are studied and discussed. An exemple of dislocation transmission through an interface is analysed in detail.


1979 ◽  
Vol 44 (7) ◽  
pp. 2009-2014 ◽  
Author(s):  
Jana Nováková ◽  
Zdeněk Dolejšek

Products of (a) allyl radical interaction with unheated Co3O4, (b) thermally activated 1,5-hexadiene or thermally activated allyl bromide with unheated Co3O4, (c) moderately heated Co3O4 with unheated 1,5-hexadiene or allyl bromide were studied under Knudsen flow conditions. Cobalt suboxide Co3O4, a typical catalyst of deep oxidations yielded acrolein in reaction with allyl radicals as early as at the room temperature of the catalyst. A similar acrolein formation was also observed in the allyl radical interaction with other oxides exhibiting different catalytic properties. It appears that acrolein is in general the primary product of the allyl radical interaction with the oxides. The results are discussed and compared with previous data obtained with MoO3.


1985 ◽  
Vol 25 (06) ◽  
pp. 945-953 ◽  
Author(s):  
Mark A. Miller ◽  
H.J. Ramey

Abstract Over the past 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. Some of the reported results, however, have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperatures. Laboratory dynamic-displacement relative permeability measurements were made on unconsolidated and consolidated sand cores with water and a refined white mineral oil. Experiments were run on 2-in. [5.1-cm] -diameter, 20-in. [52.-cm] -long cores from room temperature to 300F [149C]. Unlike previous researchers, we observed essentially no changes with temperature in either residual saturations or relative permeability relationships. We concluded that previous results may have been affected by viscous previous results may have been affected by viscous instabilities, capillary end effects, and/or difficulties in maintaining material balances. Introduction Interest in measuring relative permeabilities at elevated temperatures began in the 1960's with petroleum industry interest in thermal oil recovery. Early thermal oil recovery field operations (well heaters, steam injection, in-situ combustion) indicated oil flow rate increases far in excess of what was predicted by viscosity reductions resulting from heating. This suggested that temperature affects relative permeabilities. One of the early studies of temperature effects on relative permeabilities was presented by Edmondson, who performed dynamic displacement measurements with crude performed dynamic displacement measurements with crude and white oils and distilled water in Berea sandstone cores. Edmondson reported that residual oil saturations (ROS's) (at the end of 10 PV's of water injected) decreased with increasing temperature. Relative permeability ratios decreased with temperature at high water saturations but increased with temperature at low water saturations. A series of elevated-temperature, dynamic-displacement relative permeability measurements on clean quartz and "natural" unconsolidated sands were reported by Poston et al. Like Edmondson, Poston et al. reported a decrease in the "practical" ROS (at less than 1 % oil cut) as temperature increased. Poston et al. also reported an increase in irreducible water saturation. Although irreducible water saturations decreased with decreasing temperature, they did not revert to the original room temperature values. It was assumed that the cores became increasingly water-wet with an increase in both temperature and time; measured changes of the IFT and the contact angle with temperature increase, however, were not sufficient to explain observed effects. Davidson measured dynamic-displacement relative permeability ratios on a coarse sand and gravel core with permeability ratios on a coarse sand and gravel core with white oil displaced by distilled water, nitrogen, and superheated steam at temperatures up to 540F [282C]. Starting from irreducible water saturation, relative permeability ratio curves were similar to Edmondson's. permeability ratio curves were similar to Edmondson's. Starting from 100% oil saturation, however, the curves changed significantly only at low water saturations. A troublesome aspect of Davidson's work was that he used a hydrocarbon solvent to clean the core between experiments. No mention was made of any consideration of wettability changes, which could explain large increases in irreducible water saturations observed in some runs. Sinnokrot et al. followed Poston et al.'s suggestion of increasing water-wetness and performed water/oil capillary pressure measurements on consolidated sandstone and limestone cores from room temperature up to 325F [163C]. Sinnokrot et al confirmed that, for sandstones, irreducible water saturation appeared to increase with temperature. Capillary pressures increased with temperature, and the hysteresis between drainage and imbibition curves reduced to essentially zero at 300F [149C]. With limestone cores, however, irreducible water saturations remained constant with increase in temperature, as did capillary pressure curves. Weinbrandt et al. performed dynamic displacement experiments on small (0.24 to 0.49 cu in. [4 to 8 cm3] PV) consolidated Boise sandstone cores to 175F [75C] PV) consolidated Boise sandstone cores to 175F [75C] with distilled water and white oil. Oil relative permeabilities shifted toward high water saturations with permeabilities shifted toward high water saturations with increasing temperature, while water relative permeabilities exhibited little change. Weinbrandt et al. confirmed the findings of previous studies that irreducible water saturation increases and ROS decreases with increasing temperature. SPEJ P. 945


1994 ◽  
Vol 359 ◽  
Author(s):  
Jun Chen ◽  
Haiyan Zhang ◽  
Baoqiong Chen ◽  
Shaoqi Peng ◽  
Ning Ke ◽  
...  

ABSTRACTWe report here the results of our study on the properties of iodine-doped C60 thin films by IR and optical absorption, X-ray diffraction, and electrical conductivity measurements. The results show that there is no apparent structural change in the iodine-doped samples at room temperature in comparison with that of the undoped films. However, in the electrical conductivity measurements, an increase of more that one order of magnitude in the room temperature conductivity has been observed in the iodine-doped samples. In addition, while the conductivity of the undoped films shows thermally activated temperature dependence, the conductivity of the iodine-doped films was found to be constant over a fairly wide temperature range (from 20°C to 70°C) exhibiting a metallic feature.


2011 ◽  
Vol 133 (9) ◽  
Author(s):  
Shun Ching Lee ◽  
Tzu-Min Chen

Abstract The behavior of cryogenic nitrogen in a room-temperature evaporator six meters long is analyzed. Trapezoid fins are employed to enhance the heat flux supplied by the environment. The steady-state governing equations specified by the mixed parameters are derived from the conservations of momentum and energy. The initial value problem is solved by space integration. The fixed ambient conditions are confirmed by way of the meltback effect. An integrated model is utilized to analyze the convective effect of two-phase flow, which dominates the evaporation behavior. Another integrated model is employed to determine the total heat flux from the environment to the wet surface of the evaporator. The foundation of the formation of an ice layer surrounding the evaporator is presented. If the fin height is shorter than 0.5 m, the whole evaporator is surrounded by ice layer. If the fin height is longer than 0.5 m, the total pressure drop of nitrogen in the tube is negligible. The outlet temperature is always within the range between −12 °C and 16 °C for the evaporator with the fin height of 1.0 m. For the evaporator with dry surface, the nitrogen has the outlet temperature less than the ambient temperature at least by 5 °C.


2011 ◽  
Vol 55-57 ◽  
pp. 251-256
Author(s):  
Li Ma ◽  
Ting Zhang ◽  
Xiao Li ◽  
Zhao Hui Hu

Large-scale Ni-based super-alloy sheet has been prepared by electron beam physical vapor deposition (EB-PVD). Microstructure and the dislocation structures in the γ-γ′ double phase alloy under different temperature after tensile strain are studied with Transmission electron microscopy (TEM). The results show that the dislocation glide in single slip system and shearing mechanics, the dislocation climb with part shearing, absolute dislocation climb and cross slip, dislocation round are a course of the interacting degree between dislocation and γ′ phase gradually weakened under the tensile temperature from room temperature to high temperature, so as to decrease materials strength and increase plasticity.


2021 ◽  
Author(s):  
Zhongyan Chen ◽  
Lepeng Chen ◽  
Shou-Feng Zhang ◽  
Qianqian Zhen ◽  
Wenzhang Xiong ◽  
...  

A nickel-catalyzed synthesis of 1,3-diaryl-6H-pyrazino[2,1-b]quinazolin-6-one was developed. This method enabled to access valuable pyrazino-fused quinazolinones with tolerance of many functional groups even at room temperature. The desired pyrazino-fused quinazolinones emit...


Sign in / Sign up

Export Citation Format

Share Document