Rapid Thermal Annealing of Ion Implanted p-n Junction in Silicon

1985 ◽  
Vol 52 ◽  
Author(s):  
C. Ho ◽  
R. Kwor ◽  
C. Araujo ◽  
J. Gelpey
Keyword(s):  
Leakage Current ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Dwell Time ◽  
Annealing Temperature ◽  
Current Analysis ◽  
Junction Depth ◽  
Leakage Currents ◽  
Dopant Activation ◽  
Secondary Ion

ABSTRACTThe rapid thermal annealing (RTA) of p+n and n+p diodes, fabricated by the LOCOS process, and its subsequent effects on junction leakage current, junction depth and dopant activation were investigated. The reverse bias diode leakage currents of implanted Si <100> samples (As+: 60 KeY, 5×1014 5×1015 cm−2, B+: 25 KeV, l×1014, l×1015 cm−2 and BF2+: 45 KeV, 1×1015cm−2 ) were measured as functions of annealing temperature, and dwell time. The annealing was performed using an Eaton RTA system (Nova ROA-400) at temperatures ranging from 950 °C to 1150 °C. Annealing times ranged from 0.2 sec. to 10 sec. The results from the diode leakage current analysis are correlated with those from Secondary Ion Mass Spectroscopy (SIMS) and differential Hall measurements. The reverse-biased leakage currents from the RTA-treated samples are compared with those from furnace-annealed samples.

Boron Diffusion in Fluorine Preamorphized Silicon During Rapid Thermal Annealing

1993 ◽  
Vol 303 ◽  
Author(s):  
H. Kinoshita ◽  
T. H. Huang ◽  
D. L. Kwong ◽  
P. E. Bakeman
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealed Sample ◽  
Transmission Electron Micrograph ◽  
Boron Diffusion ◽  
Cross Sectional ◽  
Dopant Activation ◽  
Enhanced Diffusion ◽  
Transmission Electron ◽  
Secondary Ion

ABSTRACTThe effect of fluorine preamorphization on boron diffusion and activation during rapid thermal annealing (RTA) has been investigated. Compared with low energy B or BF2 implant into crystalline Si, F preamorphization suppressed the transient enhanced diffusion of B and increased dopant activation. Results show that the tail diffusion was absent, and thus the junction depth of the RTA annealed sample was established by the as-implanted B profile. Secondary ion mass spectroscopy and cross-sectional transmission electron micrograph results show F accumulation near the surface and at end-of-range defects. The interaction of F with defects is believed to reduce the B diffusion during RTA.

Modeling Dopant Redistribution During Rapid Thermal Annealing

1986 ◽  
Vol 71 ◽  
Author(s):  
Archie Y.C. Chan
Keyword(s):  
Finite Difference ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Temperature ◽  
Junction Depth ◽  
Impurity Profile ◽  
Annealing Cycle ◽  
Dopant Redistribution ◽  
Ion Implanted

AbstractThe diffusion of ion-implanted dopants in silicon during rapid thermal annealing is modeled using the finite difference method.The change in impurity profile for an initial Pearson IV boron implant is negligible(less than 1 % change in junction depth) when the peak annealing temperature(TP ) is less than 1050 °C and its duration is shorter than 20 seconds. The dopant redistribution becomes significant(greater than 25 % change in junction depth) when Tp is greater than 1200 °C and its duration is longer than 40 seconds.The heatup and cooldown portions of the transient annealing cycle are found to have little effect on dopant redistribution provided that their rates are higher than 120 °C per second.

Interaction Between Co and SiO2 During Ion-Beam Mixing and Rapid Thermal Annealing

1992 ◽  
Vol 260 ◽  
Author(s):  
C. Dehm ◽  
I. Kasko ◽  
E. P. Burte ◽  
H. Ryssel
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Temperature ◽  
Ion Beam ◽  
Ion Beam Mixing ◽  
Plan View ◽  
Implantation Energy ◽  
Transmission Electron ◽  
Co Concentration ◽  
Secondary Ion

ABSTRACTFor the application in self-aligned processes, it was supposed that CoSi2 could be superior to TiSi2, since, unlike Ti, a reaction between Co and SiO2 was not observed up to now. We studied the reaction of Co and SiO2 during ion-beam mixing and rapid thermal annealing (RTA). The influences of As and Ge implantation energy and dose were investigated in the range of 50 to 200 keV and 1–1014 to 5–1015 cm2. The annealing temperature was varied between 700° C and 1100°C.It could be demonstrated that the Co concentration in SiO2 rises with increasing Ge and As energy and dose up to values of 5·1015 cm2 compared to 2·1012 cm2 in unim-planted, annealed samples. The Co profiles in SiO2 were also studied by secondary ion mass spectroscopy (SIMS) and compared with Monte-Carlo simulations indicating pure ballistic mixing. Plan-view and cross-section transmission electron microscopy (TEM) were used to examine the SiO2 surface as well as the Co-SiO2 interface. These investigations revealed that ion-beam mixing with doses at or above 5·1014 cm2 and subsequent annealing does not damage the SiO2 unlike to unimplanted, annealed samples which show a rather severe structural change of the SiO2 surface increasing with rising annealing temperatures.

scholarly journals Synthesis of Ge1−xSnx Alloy Thin Films by Rapid Thermal Annealing of Sputtered Ge/Sn/Ge Layers on Si Substrates

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2248 ◽  
Author(s):  
Hadi Mahmodi ◽  
Md Hashim ◽  
Tetsuo Soga ◽  
Salman Alrokayan ◽  
Haseeb Khan ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Near Infrared ◽  
Annealing Temperature ◽  
Solid Phase ◽  
Infrared Region ◽  
Alloy Formation ◽  
Phase Mixing ◽  
Si Substrates ◽  
Msm Photodetector

In this work, nanocrystalline Ge1−xSnx alloy formation from a rapid thermal annealed Ge/Sn/Ge multilayer has been presented. The multilayer was magnetron sputtered onto the Silicon substrate. This was followed by annealing the layers by rapid thermal annealing, at temperatures of 300 °C, 350 °C, 400 °C, and 450 °C, for 10 s. Then, the effect of thermal annealing on the morphological, structural, and optical characteristics of the synthesized Ge1−xSnx alloys were investigated. The nanocrystalline Ge1−xSnx formation was revealed by high-resolution X-ray diffraction (HR-XRD) measurements, which showed the orientation of (111). Raman results showed that phonon intensities of the Ge-Ge vibrations were improved with an increase in the annealing temperature. The results evidently showed that raising the annealing temperature led to improvements in the crystalline quality of the layers. It was demonstrated that Ge-Sn solid-phase mixing had occurred at a low temperature of 400 °C, which led to the creation of a Ge1−xSnx alloy. In addition, spectral photo-responsivity of a fabricated Ge1−xSnx metal-semiconductor-metal (MSM) photodetector exhibited its extending wavelength into the near-infrared region (820 nm).

Impact of rapid thermal annealing and hydrogenation on the doping concentration and carrier mobility in solid phase crystallized poly-Si thin films

2011 ◽  
Vol 1321 ◽  
Author(s):  
A. Kumar ◽  
P.I. Widenborg ◽  
H. Hidayat ◽  
Qiu Zixuan ◽  
A.G. Aberle
Keyword(s):  
Thin Films ◽  
Electronic Properties ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Carrier Mobility ◽  
Crystalline Silicon ◽  
Solid Phase ◽  
Dopant Activation ◽  
Hall Effect Measurements ◽  
Probe Measurements

ABSTRACTThe effect of the rapid thermal annealing (RTA) and hydrogenation step on the electronic properties of the n+ and p+ solid phase crystallized (SPC) poly-crystalline silicon (poly-Si) thin films was investigated using Hall effect measurements and four-point-probe measurements. Both the RTA and hydrogenation step were found to affect the electronic properties of doped poly-Si thin films. The RTA step was found to have the largest impact on the dopant activation and majority carrier mobility of the p+ SPC poly-Si thin films. A very high Hall mobility of 71 cm2/Vs for n+ poly-Si and 35 cm2/Vs for p+ poly-Si at the carrier concentration of 2×1019 cm-3 and 4.5×1019 cm-3, respectively, were obtained.

Ajustement par recuits rapides RTA (rapid thermal annealing) des contraintes dans des couches minces de tungstène utilisées comme absorbant pour des masques à rayons X

1991 ◽  
Vol 69 (3-4) ◽  
pp. 451-455 ◽  
Author(s):  
H. Lafontaine ◽  
J. F. Currie ◽  
S. Boily ◽  
M. Chaker ◽  
H. Pépin
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Temperature ◽  
Rf Power ◽  
X Ray ◽  
Stress Changes ◽  
Different Temperatures ◽  
Absorbing Layer ◽  
Good Agreement ◽  
Sputtering System

Tungsten thin films are deposited with a triode sputtering system in order to obtain an absorbing layer for X-ray masks. The mechanical stress is studied as a function of different pressure and RF power conditions during deposition. Rapid thermal annealing at different temperatures and durations is performed in order to produce films under low compressive stress. We observe that the stress changes occur over the time scale of seconds at the annealing temperature and that the corresponding activation energies are low (60 meV). Grain growth in a preferred orientation explains the observed changes in stress. The magnitude in the change of stress is in good agreement with a model proposed by Hoffman et al. relating the stress to grain size and grain boundary dimensions. [Journal translation]

scholarly journals Effect of rapid thermal annealing on structural and optical properties of ZnS thin films fabricated by RF magnetron sputtering technique

2019 ◽  
Vol 14 (1) ◽  
pp. 53-63 ◽  
Author(s):  
M. S. Bashar ◽  
Rummana Matin ◽  
Munira Sultana ◽  
Ayesha Siddika ◽  
M. Rahaman ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Carrier Concentration ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Temperature ◽  
Annealing Treatment ◽  
Localized States ◽  
Stoichiometric Ratio ◽  
Deposited Films

AbstractThe ZnS thin films have been deposited by radio frequency magnetron sputtering at room temperature. Post-deposition rapid thermal annealing treatment was done for the films deposited at different powers ranging from 70 to 100 W. One peak is observed for as-deposited and annealed thin films at around 28.48° corresponding to the (111) reflection plane indicating a zincblende structure. The overall intensity of the peaks and the FWHM values of as-deposited films increased after annealing corresponding to the increase in crystallinity. The optical energy bandgap is found in the range of 3.24–3.32 eV. With increasing annealing temperature, the decrease in the Urbach energy values indicating a decrease in localized states which is in good agreement with the XRD results where the crystallinity increased. The surface morphology of the films seems to be composed of Nano-granules with a compact arrangement. Apparently, the grain size increases in the deposited films as annealing temperature increases. The compositional ratio attained close to the stoichiometric ratio of 1:1 after annealing. From the Hall effect measurement, the carrier concentration and mobility are found to increase after annealing. The high carrier concentration and mobility also comply with structural and optical analysis. Best results are found for the film annealed at 400 °C deposited at 90 W.

Sign in / Sign up

Export Citation Format

Share Document