Effect of Bottom Electrode System on Ferroelectric Properties of Sputter Deposited PZT Capacitors

1998 ◽  
Vol 541 ◽  
Author(s):  
Kwon Hong ◽  
Yong Sik Yu ◽  
Shang Kyoo Lee
Keyword(s):  
Bottom Electrode ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Electrode System ◽  
Fatigue Properties ◽  
Si Substrates ◽  
Pzt Films ◽  
Current Characteristics ◽  
Sputter Deposited ◽  
Electrode Systems

AbstractRF magnetron sputter deposited PZT films were prepared on various bottom electrode systems such as Pt/Ti/SiO2/Si, IrO2/SiO2/Si, Pt/IrO2/SiO2/Si and Ir/IrO2/SiO2/Si substrates using the ceramic PZT target with Pb1.1(Zr0.52Ti0.48)O3 composition. In order to obtain single perovskite phase, PZT films were sputter-deposited at room temperature under Ar only plasma condition followed by high temperature annealing under oxygen ambient. Regardless of the bottom electrode system, reasonable ferroelectric properties such as 2Pp, Vc could be obtained by 650°C post annealing. Their values were over 20μ C/cm2 and below ± 1.OV when drive voltage was ± 3V, respectively. Hybrid electrode system, namely, thick Pt or Ir and thin IrO2 shows good leakage current characteristics, of ∼ 10−8A/cm2. Fatigue properties of PZT capacitor depend on the test condition. However, retention after 3×104sec showed a degradation of 15% when writing voltage was −5V irrespective of bottom electrode system. Imprint characteristics also showed good results within ± 1 as a figure of merit (FOM).

Dependence of Ferroelectric Properties of SBT Based Capacitors on the Electrode Material

1998 ◽  
Vol 541 ◽  
Author(s):  
S. Tirumala ◽  
S. O. Ryu ◽  
K. B. Lee ◽  
R. Vedula ◽  
S. B. Desu
Keyword(s):  
Thin Films ◽  
Electrode Material ◽  
Electrode Materials ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Si Substrates ◽  
Non Volatile Memory ◽  
Metal Organic ◽  
Sputter Deposited ◽  
Memory Applications

AbstractThe effect of various electrode materials on the ferroelectric properties of SrBi2Ta2O9 (SBT) thin films has been investigated for non-volatile memory applications. Two sets of electrode structures, viz., Pt-Ir based and Pt-Rh based, were sputter deposited in-situ on Si substrates. SBT thin films were deposited on these electrodes using a metal-organic solution deposition technique followed by a post-deposition anneal at 750 °C in oxygen. Structural characterization revealed a polycrystalline nature with predominant perovskite phase in SBT thin films. Ferroelectric properties were studied in capacitor mode by depositing top electrodes, where the top electrode material is identical to that of the bottom electrode. Extensive analysis of the ferroelectric properties signify the important role played by the electrode material in establishing the device applicability is reported in this work.

Effect of Pb Content on the Fatigue Properties of D.C. Reactive Sputtering-Derived PZT Thin Films

2006 ◽  
Vol 326-328 ◽  
pp. 613-616
Author(s):  
Dae Jin Yang ◽  
Seong Je Cho ◽  
Jong Oh Kim ◽  
Won Youl Choi
Keyword(s):  
Lead Zirconate Titanate ◽  
Perovskite Phase ◽  
Fatigue Behavior ◽  
Ferroelectric Properties ◽  
Pyrochlore Phase ◽  
Reactive Sputtering ◽  
Lead Zirconate ◽  
Fatigue Properties ◽  
Pzt Thin Films ◽  
Pzt Films

Lead zirconate titanate (Pb(Zr0.48Ti0.52)O3 or PZT) films were grown on platinized silicon wafers (Pt/SiO2/Si) by d.c. reactive sputtering method with multi targets. The Pb content of PZT films has been widely recognized as affecting not only the phase formation and microstructure but also the dielectric and ferroelectric properties. Pb content of PZT films was controlled by the variation of Pb target current. The relation between Pb content and Pb target current was expressed as y=0.89x-11.09. The x and y are Pb target current and Pb content, respectively. The pyrochlore phase was transformed to perovskite phase as Pb content was increased. This phase transformation improved the ferroelectric properties of PZT films. In PZT films with perovskite phase, fatigue properties were not improved with excess Pb content. Fatigue properties of PZT films began to be fatigued after 106 switching cycles and coincided with the typical PZT fatigue behavior. Excess Pb content (Pb vacancy) did not affect the fatigue properties of PZT films.

Issues in the Flexible Integration of Sputter-Deposited PZT Thin Films with Polysilicon and Ti/Pt Electrode Layers for Use as Sensors and Actuators in Microelectromechanical Systems (MEMS)

2000 ◽  
Vol 657 ◽  
Author(s):  
C.F. Knollenberg ◽  
T.D. Sands ◽  
A.S. Nickles ◽  
R.M. White
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Microelectromechanical Systems ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Pt Electrode ◽  
Electrode Layer ◽  
Pzt Thin Films ◽  
Pzt Films ◽  
Sputter Deposited

ABSTRACTSputter-deposited piezoelectric lead zirconate titanate (PZT) thin films with Ti/Pt and polysilicon electrode layers are being investigated for use in Microelectromechanical Systems (MEMS). Existing research shows the nucleation of the perovskite phase of the PZT is linked to the lattice spacing of the underlying Pt electrode and/or seed layers, and is key in obtaining PZT layers with good piezoelectric/ferroelectric properties. Our research with piezoelectric PZT films on Ti/Pt electrode layers aims at employing these films to generate and receive acoustic waves in flexural plate wave devices (FPWs). Our experiments indicate the formation of a random polycrystalline perovskite phase is linked to the emergence of oriented <100> Pt grains within the dominant <111>-oriented crystal structure during rapid thermal annealing in an oxygen environment. Pt films annealed in nitrogen, in contrast, retained their <111> preferential orientation without the formation of Pt <100> grains. PZT films deposited on these electrodes and annealed in nitrogen were strongly oriented in the <111> direction, but exhibited lossy ferroelectric behavior and were prone to delamination. We are also investigating the feasibility of using doped polysilicon electrode layers with PZT thin films. The multiple layers used with the Pt electrode (Pt, Ti, and SiO2 adhesion layer) have significant interactions with one another, and replacing these layers with a single electrode layer should alleviate these complications. A low-temperature PZT deposition process (300°C) and short annealing cycles (30 sec.), coupled with a TiO2 barrier/seed layer should prevent interdiffusion and reactions between the polysilicon and PZT layers. Our experiments show that PZT films deposited and annealed on doped polysilicon layers develop a random polycrystalline perovskite phase, but are subject to tensile cracking. The use of polysilicon as an electrode layer should also facilitate the integration of piezoelectric PZT layers with polysilicon surface micromachined structures using SiGe sacrificial layers.

Effects of Sputter-Deposited LaNiO3 Electrode on the Deposition and Properties of Ferroelectric Thin Films

1996 ◽  
Vol 433 ◽  
Author(s):  
T. B. Wu ◽  
J. M. Wu ◽  
C. M. Wu ◽  
M. J. Shyu ◽  
M. S. Chen ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Perovskite Phase ◽  
Sol Gel ◽  
Processing Condition ◽  
Fatigue Property ◽  
Rf Magnetron Sputtering ◽  
Ferroelectric Films ◽  
Si Substrates ◽  
Sputter Deposited

AbstractHighly (100)-textured thin film of metallic LaNiO3 (LNO) was grown on the Pt/Ti/SiO2/Si substrates by rf magnetron sputtering at ˜300°C, which was used as a bottom electrode to prepare highly (100)-textured ferroelectric films. Examples on the deposition of PbTiO3, (Pbl−xLax)TiO3, Pb(Zr0.53Ti0.47)O3, Pb[(Mg1/3Nb2/3)1−xTix]O3, and (Ba1−xSrx)TiO3 thin films by rf magnetron sputtering or sol-gel method are shown. A reduction of temperature for perovskite phase formation can be achieved, especially for those difficult to crystallize. The surface roughness of the ferroelectric films is also improved as compared to that of films deposited on conventional Pt electrode. Although the electrical properties of the ferroelectric films are affected by the out-diffusion of LNO when a higher temperature was used in the preparation of the films, under an appropriate processing condition, the highly (100)-textured films can have satisfactory electrical characteristics for application. Moreover, the polarization-fatigue property can be also improved by the use of LNO electrode.

Ferroelectric Properties of Pb(Zr,Ti)O3 Thin Film Capacitors Made by RF Magnetron Sputtering and Heat-Treated by the Bottom Electrode Crystallization Method

2006 ◽  
Vol 514-516 ◽  
pp. 1348-1352
Author(s):  
Andréi I. Mardare ◽  
Cezarina C. Mardare ◽  
Raluca Savu
Keyword(s):  
Thin Film ◽  
Magnetron Sputtering ◽  
Bottom Electrode ◽  
Ferroelectric Properties ◽  
Electrical Contact ◽  
Rf Magnetron Sputtering ◽  
Electrical Contacts ◽  
Sem Images ◽  
Heat Treated ◽  
Pzt Films

The bottom electrode crystallization (BEC) method was applied to the crystallization of Pb(Zr,Ti)O3 (PZT) thin films deposited by RF magnetron sputtering on Pt/Ti/SiO2/Si substrates. Using a proportional-integral-differential controller, the current flowing in the Pt/Ti films provided accurately controlled Joule heating for the crystallization of the PZT films. The temperature uniformity of the heat treatments was investigated by measuring the ferroelectric properties of PZT. Platinum and tungsten wires were alternatively used as electrical contacts. Scanning electron microscopy (SEM) images were used to inspect the electrical contact regions between the platinum films and different contact wires. The PZT films showed higher remanent polarizations and lower leakage currents near the electrical contacts when Pt wires were used; the ferroelectric properties were more uniform on the PZT films heat-treated with W contact wires. The BEC method can successfully replace the more conventional means for thin film crystallization, having the advantage of being a very precise, low cost and low power consumption technique.

scholarly journals Microstructure and Properties of PZT Films with Different PbO Content—Ionic Mechanism of Built-In Fields Formation

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2926 ◽  
Author(s):  
Nikolay Mukhin ◽  
Dmitry Chigirev ◽  
Liubov Bakhchova ◽  
Andrey Tumarkin
Keyword(s):  
Lead Zirconate Titanate ◽  
Lead Oxide ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Experimental Studies ◽  
Rf Magnetron Sputtering ◽  
Lead Zirconate ◽  
Heterophase Structure ◽  
Pzt Films ◽  
A Charge

Experimental studies were conducted on the effects of lead oxide on the microstructure and the ferroelectric properties of lead zirconate-titanate (PZT) films obtained by the method of radio frequency (RF) magnetron sputtering of a ceramic PZT target and PbO2 powder with subsequent heat treatment. It is shown that the change in ferroelectric properties of polycrystalline PZT films is attributable to their heterophase structure with impurities of lead oxide. It is also shown that, even in the original stoichiometric PZT film, under certain conditions (temperature above 580 °C, duration greater than 70 min), impurities of lead oxide may be formed. The presence of a sublayer of lead oxide leads to a denser formation of crystallization centers of the perovskite phase, resulting in a reduction of the grain size as well as the emergence of a charge on the lower interface. The formation of the perovskite structure under high-temperature annealing is accompanied by the diffusion of lead into the surface of the film. Also shown is the effect of the lead ions segregation on the formation of the self-polarized state of thin PZT films.

Laser-Assisted Low Temperature Processing of PZT Thin Films

1997 ◽  
Vol 493 ◽  
Author(s):  
Yongfei Zhu ◽  
Jinsong Zhu ◽  
Y. J. Song ◽  
S. B. Desu
Keyword(s):  
Thin Films ◽  
Low Temperatures ◽  
Laser Annealing ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Processing Temperature ◽  
Pzt Thin Films ◽  
Step Process ◽  
Pzt Films ◽  
One Step

ABSTRACTA novel method for lowering processing temperature of ferroelectric Pb(Zr1−xTix)O3 (PZT) thin films was developed utilizing a laser-assisted two-step process. In the first step, perovskite phase was initiated in the PZT films by subjecting the films to a fornace anneal at low temperatures in the range of 470 °C to 550 °C depending on the Zr/Ti ratio. Later, the films were laser-annealed (using krF excimer laser) at room temperature to grow the perovskite phase, and to improve microstructure and ferroelectric properties. It was found that this two-step process was very effective in producing excellent quality ferroelectric PZT films at low temperatures. It should be noted that although laser annealing of amorphous and/or pyrochlore films directly (one-step process) produces perovskite phase, the ferroelectric properties of these films, irrespective of the composition, were rather unattractive. Some possible reasons for the ineffectiveness of the one-step process were discussed.

Dielectric and Ferroelectric Characterization of Sol-Gel Derived Ca-Doped PbTiO3 Thin Films

1996 ◽  
Vol 433 ◽  
Author(s):  
G. Teowee ◽  
K.C. McCarthy ◽  
E.K. Franke ◽  
J.M. Boulton ◽  
T.P. Alexander ◽  
...  
Keyword(s):  
Thin Films ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Test System ◽  
Impedance Analyzer ◽  
Si Substrates ◽  
Phase Development ◽  
Pt Electrodes

AbstractA series of sol-gel derived CaTiO3- PbTiO3 thin films ( i.e. Pb1−xCaxTiO3 with x = 0 − 1) was prepared on platinized Si substrates and fired to temperatures ranging from 550C to 650C. Multiple spincoating was performed to obtain films up to 0.5 μm thick with an intermediate firing of 400C between coatings. After the final crystallization firing, top Pt electrodes were sputtered to form monolithic capacitors. These capacitors were subjected to dielectric and ferroelectric characterization using an impedance analyzer and Radiant Technology RT66A Ferroelectric Test System. XRD was used to study the phase development and phase assembly of the fired films. All compositions were single perovskite phase after firing to 600C. The effects of Ca content on the crystallization behavior and ferroelectric properties are discussed.

Sign in / Sign up

Export Citation Format

Share Document